Yamaha 2006 FJR1300AS Service Manual page 31

1. Grip warmer couplers
2. Hand shift switch coupler
3. Handlebar switch couplers
4. Right grip warmer lead
5. Right handlebar switch lead
6. Immobilizer unit lead
7. Main switch lead
8. Hand shift switch lead
9. Left grip warmer lead
10. Left handlebar switch lead
11. Stator coil lead
12. Air filter case breather hose
13. Gear position sensor lead
14. Foot shift switch lead
15. Fuel tank breather/overflow hose
16. Clutch hose
17. Sidestand switch
18. Sidestand switch lead
19. Oil level switch lead
20. Coolant reservoir breather hose
21. Brake hose (hydraulic unit to left front brake
caliper)
22. Front wheel sensor
23. Front wheel sensor lead
24. Front left turn signal light lead
25. Brake pipe (metering valve to right front brake
caliper)
26. Brake pipe (hydraulic unit to front brake calipers)
27. Brake pipe (front brake master cylinder to hydraulic
unit)
28. Wire harness
29. Crankshaft position sensor lead
30. Starter motor lead
31. Neutral switch coupler
32. YCC-S speed sensor
33. Oil level switch coupler
34. Upper crankcase
35. Rear balancer cover
A. Secure the plastic band by inserting the projection
on the band into the hole in the windshield drive
unit/meter assembly stay, and then fasten the
handlebar switch leads, grip warmer leads and
hand shift switch lead with the band, making sure
that the end of the band faces down. Do not cut off
the excess end of the plastic band.
B. Secure the plastic band by inserting the projection
on the band into the hole in the windshield drive
unit/meter assembly stay, and then fasten the
handlebar switch leads, grip warmer leads, hand
shift switch lead and front wheel sensor lead with
the band, making sure that the end of the band
faces down. Do not cut off the excess end of the
plastic band.
C. To oil level switch
D. Fasten the leads (to oil level switch and crankshaft
position sensor) that branch off from the wire
harness to the guide on the holder with a plastic
locking tie, making sure that the end of the tie faces
upward. Do not cut off the excess end of the plastic
locking tie.
E. Fasten the sidestand switch lead, stator coil lead,
and oil level switch lead with a plastic locking tie,
making sure to bundle and fasten the sidestand
switch lead so that the coupler is positioned to the
front of the tie. Face the end of the plastic locking
tie outward. Do not cut off the excess end of the
plastic locking tie.
F. To fuel tank
G. Pass the fuel tank breather/overflow hose through
the guide on the universal joint dust cover.
H. Pass the air filter case breather hose through the
guide on the muffler bracket.
I. Fasten the clutch hose with the pivot shaft locknut
retainer.
–
J. 43 53 mm (1.69
–
K. 60 70 mm (2.36
L. Fasten the grommets on the front wheel sensor
lead and the brake hose (hydraulic unit to left front
brake caliper) with the holder.
M. Route the front wheel sensor lead to the outside of
the left front brake caliper lower mounting boss and
the boss for the left front fork compression
damping force adjusting screw.
N. Fasten the grommet on the front wheel sensor lead
with the holder.
O. Route the front wheel sensor lead between the left
front brake caliper and the brake hose (hydraulic
unit to left front brake caliper).
P. Fasten the front wheel sensor lead to the brake
hose (hydraulic unit to left front brake caliper) with
the two holders, making sure to position the lead to
the inside of the hose.
Q. Route the fuel tank breather/overflow hose to the
front of the clutch hose, then through the opening
between the frame and the swingarm.
R. Face the ends of the clamp to the left, making sure
that the lower end contacts the wire harness.
S. Fasten the oil level switch lead and starter motor
lead with the clamp.
T. To sidestand switch
U. Route the starter motor lead between the rear
balancer cover bolt and the rib on the crankcase.
– 22 –
CABLE ROUTING
–
2.09 in)
–
2.76 in)