Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt DW770
Summary of Contents for DeWalt DW770
- Page 1 DW770 DW771 DW777 www.
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Figure 1 DW771 Figure 2...
- Page 4 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10...
- Page 5 Figure 11 Figure 12 v v Figure 13 Figure 14 Figure 16 Figure 15...
- Page 6 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22...
- Page 7 Figure 24 Figure 23 Figure 25 Figure 26 Figure 27...
-
Page 8: Technical Data
EN G LI S H DW770, DW771, DW777 CROSS-CUT MITRE SAW Congratulations! NOTE: This device is intended for the connection to a power supply system with maximum permissible system impedance Zmax of You have chosen a D WALT tool. Years of experience, thorough 0.25 Ohm at the interface point (power service box) of user’s supply. -
Page 9: General Safety Rules
ENGLISH SAVE THIS MANUAL FOR FUTURE REFERENCE 17. Avoid unintentional starting. Do not carry the tool with a finger on the switch. Be sure that the General Safety Rules tool is in the “off” position before plugging in. 1. Keep work area clear. 18. -
Page 10: Residual Risks
• Refrain from removing any cut-offs or other parts of the workpiece from the cutting area while the machine is running and the saw 2 Dust extraction nozzles (optional for DW770) head is not in the rest position 1 Instruction manual •... -
Page 11: Using An Extension Cable
DW770 LX: H05RR-F, 2x1.5 mm² p. Sliding fence DW777 / DW771: H07RN-F, 2x1.0 mm² q. Dust extraction nozzle (optional for DW770) DW777 LX / DW771 LX: H05RR-F, 2x1.5 mm² r. Traverse lock Mains Plug Replacement s. Guard lock up hook (U.K. -
Page 12: Prior To Operation
EN G LI S H Mounting the Saw Blade (fi g. 1, 8–10) Checking and Adjusting the Blade to the Fence (fi g. 2, 14, 15) WARNING: To reduce the risk of injury, turn unit off and disconnect machine from power source before 1. -
Page 13: Operation
ENGLISH • Although this saw will cut wood and many nonferrous 2. Engage the mitre latch (m) at the 0° position and fasten the mitre materials,these operating instructions refer to the cutting latch. of wood only. The sameguide-lines apply to the other 3. -
Page 14: Maintenance
ENG LI SH 3. Loosen the knob to adjust the clamp up or down, then use the fine – Guide rails (500 or 1,000 mm) (ii). adjust knob to firmly clamp the workpiece. – Stands (mm) to support the guide rails. Do not use the stands to support the machine! The height of the stands is adjustable. -
Page 15: Optional Accessories
E NG L I S H Should you find one day that your D WALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Cleaning Separate collection of used products and packaging allows materials to be recycled and used again. - Page 16 Dutch Tel: 32 70 220 063 Fax: 32 70 225 585 Luxembourg Nieuwlandlaan 7, IZ Aarschot B156 French Tel: 32 70 220 062 Fax: 32 70 222 441 België en B-3200 Aarschot www.dewalt.be Luxemburg Danmark WALT Tlf: 70201511 Sluseholmen 2-4 Fax: 70224910 2450 København SV www.dewalt.dk...