Activating The Surround Modes; Activating The Ex/Es Setting - JVC RX-7032VSL Instructions Manual

Activating the Surround Modes

Available Surround modes vary depending on the speaker settings
and the incoming signals. (See page 32.)
Activating one of the Surround modes for a source automatically
recalls the memorized settings and adjustments (see pages 23 to
31.)
You can also use the buttons on the remote control for the same
functions.

Activating the EX/ES setting

For multi-channel digital software, you can activate the EX/ES (7.1-
channel) reproduction mode.
• Once you have set EX/ES (7.1-channel) reproduction mode, it is
stored in memory and will be called up whenever you activate the
Surround mode which the memorized EX/ES (7.1-channel)
reproduction mode can be applied to.
Press EX/ES to select an appropriate setting for your enjoyment.
The currently selected EX/ES (7.1-channel) reproduction mode
appears on the display.
• Each time you press the button, it changes as follows:
EX/ES AUTO*: According to the incoming signal, an
appropriate Surround mode is applied.
• For Dolby Digital EX and DTS-ES,
EX/ES (7.1-channel) reproduction is
applied.
• For 5.1-channel (or less) encoded
software, 5.1-channel reproduction is
applied.
EX/ES ON*: Select to apply EX/ES (7.1-channel)
reproduction to both 5.1-channel and 6.1-
channel encoded software.
EX/ES OFF: Select to cancel the EX/ES (7.1-channel)
reproduction.
* If the surround back speakers are not connected or deactivated,
Virtual 6.1-channel surround is applied.
Notes:
• When Surround mode is deactivated, pressing EX/ES will
activate an appropriate Surround mode for the current source.
• When an analog or digital 2-channel source is playing, you can
adjust the EX/ES (7.1-channel) reproduction mode and store
the setting, but it will not affect the current source.
• When the source is one to which the EX/ES (7.1-channel)
reproduction cannot be applied, you can adjust the setting and
store in memory, but reproduction channels will remain
unchanged.
35
RX-7032V AUDIO/VIDEO CONTROL RECEIVER
Activating the Surround Modes
RX-7032V
1. Select and play any source other than "DVD
MULTI."
• Make sure you have selected the analog or digital input mode.
• Surround modes are not valid for DVD MULTI playback
mode.
2. Press SURROUND to activate the Surround
mode.
• For multi-channel digital software (except 2-channel and
Dual Mono software), incoming signals are automatically
detected and the appropriate surround mode is activated (see
page 34 for details).
DIGITAL AUTO
L C R
LINEAR PCM
SUBWFR LFE DIGITAL
LS RS
Ex. When "DOLBY D" is activated.
– If the EX/ES (7.1-channel) reproduction mode has been set
to "AUTO" or "ON," one of the EX/ES (7.1-channel)
reproduction modes will be activated (see the left column).
• For analog sources and digital 2-channel software, you can
select one of the following Surround modes. Each time you
press SURROUND, Surround modes change as follows:
ANALOG
L R LINEAR PCM
SUBWFR
PL MOVIE PL
II
NEO:6MUSIC
• For Dual Mono software, you can select the channel you
listen to. (See page 27.)
DUAL DIGITAL AUTO
L LINEAR PCM
SUBWFR DIGITAL
To adjust the speaker output level, see pages 30 and 31.
To cancel the Surround mode
Press SURROUND/DSP OFF (or SURR/DSP OFF on the remote
control). "SURR OFF" appears on the display.
AUDIO/VIDEO CONTROL RECEIVER
SPEAKERS 1
VOLUME
PRO LOGIC
SPEAKERS 1
VOLUME
MUSIC PRO LOGIC
II
NEO:6CINMA
SPEAKERS 1
VOLUME