Using Headphones; Using The Tuner; Tuning Stations Automatically; Tuning Stations Manually - Kenwood SPECTRUM 350 Setting Up

Using headphones

You can use headphones to listen to music in private.
1 Turn the speakers OFF.
2 Insert the headphone plug into the HEADPHONE
jack, and then put them on.
AM-FM STEREO RECEIVER KR-596
BAND
AUTO/MANU. +10
MEMORY 1 2 3
P.CALL 6 7 8
AUTO TUNING SYSTEM
30 STATION RANDOM PRESET
VOLUME CONTROL
DOWN
SPEAKERS
BASS TREBLE
FLAT 2 FLAT 2 STANDBY INPUT SELECTOR
2 2
4 4 4 4
6 6 6 6
8 8 8 8
-10 +10 -10 +10
SPEAKERS
POWER
PHONES L BALANCE R
ON/STANDBY
2 1
16.
Important
There are a few things to keep in mind when using head-
phones:
Turn the volume down before switching the speakers
back on.
You can use your headphones with the speakers on
but be careful. The volume delivered through the
headphones is usually lower than that delivered
TUNING
through speakers. When you turn up the volume for
4 5
the headphones, be careful not to turn it up so loud
9 0
you damage your speakers.
UP

Using the tuner

Tuning stations automatically

You can automatically find the strongest radio
station signals.
1 Select the TUNER input.
2 Press the BAND button to select FM or AM.
3 Press the AUTO/MANU button to select AUTO.
The AUTO indicator light turns ON.
4 On the TUNING buttons, press to move up
the broadcast band, or to move down the
broadcast band.
The tuner stops automatically when it finds a strong
station, and the TUNED light turns ON. If the station
is broadcasting in stereo, the STEREO light turns ON.
5 Press or again to find the next strong signal.
3 2 4 5
AM-FM STEREO RECEIVER KR-596
BAND TUNING
AUTO/MANU. +10
MEMORY 1 2 3 4 5
P.CALL 6 7 8 9 0
AUTO TUNING SYSTEM
30 STATION RANDOM PRESET
VOLUME CONTROL
DOWN UP
SPEAKERS
BASS TREBLE
STANDBY
FLAT 2 FLAT 2 INPUT SELECTOR
2 2
4 4 4 4
6 6 6 6
8 8 8 8
-10 +10 -10 +10
SPEAKERS
POWER
PHONES L BALANCE R
ON/STANDBY
1

Tuning stations manually

You can search for radio stations in small steps up and
down the broadcast band to tune in a weak station that
automatic tuning might miss.
1 Select the TUNER input.
2 Press the BAND button to select FM or AM.
3 Press the AUTO/MANU button to select MANUAL.
The AUTO indicator light turns OFF.
4 On the TUNING buttons, press to move up the
broadcast band, or to move down the broadcast
band to the station you want.
The frequency changes by 0.1 MHz each time you
press the button, or it continually changes if you hold
the button down.
3 2 4
AM-FM STEREO RECEIVER KR-596
BAND TUNING
AUTO/MANU. +10
MEMORY 1 2 3 4 5
P.CALL 6 7 8 9 0
AUTO TUNING SYSTEM
30 STATION RANDOM PRESET
VOLUME CONTROL
DOWN UP
SPEAKERS
BASS TREBLE
STANDBY
FLAT 2 FLAT 2 INPUT SELECTOR
2 2
4 4 4 4
6 6 6 6
8 8 8 8
-10 +10 -10 +10
SPEAKERS
POWER
PHONES L BALANCE R
ON/STANDBY
1
Important
During manual tuning, the tuner receives stations only
in mono.
To receive a tuned station in stereo, press the
AUTO/MANU button so the AUTO light turns ON.
If the station is broadcast in stereo, you receive it in
stereo.
You may receive weaker stations with more back-
ground noise in stereo than in mono. To decrease the
noise, press the AUTO/MANU button so the AUTO
light goes OFF.
17.