Table of Contents
Advertisement
2
Before You Talk
on 1
The unit has 14 operating frequency channels and 38 group codes.
To talk to others, all users in your group must be using the same
channel and group code.
2-A Selecting the Operating Channel
The factory preset is "1".
(MENU)
1 Press
.
" and the current channel will flash
≥"
on the display.
(›)
(‹)
2 Press
or
desired operating channel (1–14) is
displayed.
3 When finished, press
10 seconds.
≥ The selected channel will not be cleared even when you turn off
the unit.
2-B Selecting the Group Code (CTCSS)
The Continuous Tone Coded Squelch System (CTCSS) allows you
to ignore (not hear) unwanted calls from other persons who are
using the same channel. It provides communication with silent
standby since you will only receive calls from group members using
the same group code. The unit is equipped with 38 group codes.
The factory preset is "0" (OFF).
ng
The CTCSS does not make your conversation private. It only
allows you to not listen to unwanted conversations.
(MENU)
1 Press
twice.
d
" and the current group code will
≥"
flash on the display.
(›)
(‹)
2 Press
or
desired group code (0–38) is displayed
(see below).
3 When finished, press
10 seconds.
≥ The selected code will not be cleared even when you turn off the
unit.
≥ To communicate with others without a group code, select "0"
(OFF) in step 2.
CTCSS code
No.
Freq.
No.
B.
1
67.0
11
2
71.9
12
3
74.4
13
4
77.0
14
5
79.7
15
6
82.5
16
7
85.4
17
8
88.5
18
9
91.5
19
ALK)
10
94.8
20
Section 2
repeatedly until the
(TALK)
or wait for
repeatedly until the
(TALK)
or wait for
Freq.
No.
Freq.
No.
97.4
21
136.5
31
100.0
22
141.3
32
103.5
23
146.2
33
107.2
24
151.4
34
110.9
25
156.7
35
114.8
26
162.2
36
118.8
27
167.9
37
123.0
28
173.8
38
127.3
29
179.9
0
131.8
30
186.2
3
To Communicate
Backlit LCD Display
The lighted display will remain
on for about 5 seconds after
pressing any button except
(TALK) or closing the flip.
Ear Speaker
(TALK)
(MENU)
(‹), (›)
Main Speaker
Flip
3-A Monitor
The monitor function activates the speaker. Use this function when
received signals are too weak to recognize. You can use the monitor
function to check activity on the current channel before transmission.
1 Press and hold
≥The TALK/BUSY indicator lights green.
≥You will hear static if the channel is clear for use.
(MONITOR)
2 Release
≥The TALK/BUSY indicator light goes out.
≥ If you want to use the monitor privately, open the flip before
pressing (MONITOR) .
3-B Sending/Receiving Messages
1 Check the current channel activity (3-A).
≥Do not talk if someone is already on the channel.
2 Press and hold
microphone.
≥The TALK/BUSY indicator lights red.
3 To receive, release
≥The TALK/BUSY indicator lights green.
≥Repeat steps 2 and 3 to continue communication.
≥ To maximize readability of your transmitted signal,
(unit: Hz)
pause a few seconds after pressing (TALK) , hold
Freq.
the unit 2 to 4 inches (5 to 10 cm ) from your mouth
and speak at a normal voice level.
192.8
≥ For safe motor vehicle operation, please do not use the unit while
203.5
driving. Either stop your vehicle or allow a passenger to use the
210.7
unit.
218.1
225.7
To select the main speaker volume
233.6
The factory preset is "5".
241.8
(›)
(‹)
1 Press
or
250.3
VOL " and the current volume level will flash on the display.
≥"
OFF
(›)
(‹)
2 Press
or
(1–8) is displayed.
Display
(CALL)
(MONITOR)
TALK/BUSY Indicator
Microphone
(MONITOR)
to open the squelch.
to close the squelch.
(TALK)
to transmit and talk into the
(TALK)
.
.
repeatedly until the desired volume level
Advertisement
Table of Contents
