Panasonic AW-HE130KP Operating Instructions Manual page 73

Web screen configurations (continued)
Refresh interval (JPEG)
Select the frame rate for JPEG images.
Setting value:
For 59.94Hz:
1fps/2fps/3fps/5fps/6fps /10fps
1
*
For 50Hz:
1fps/2fps/5fps/10fps /12.5fps
1
*
Factory settings: 5fps
*
1
When [H.264 transmission] is set to [On], the frame rate may be
slower than the specified value in some cases.
<NOTE>
• The frame rate may be slower depending on the network
environment, resolution, image quality, access volume, etc.
• If images are not transmitted at the specified frame rate, lowering
the resolution or image quality may result in transmissions closer to
the specified value.
Image quality (JPEG)
When displaying JPEG images in the Live screen, set the quality of
the first image that appears to [Quality1] or [Quality2].
Setting value:
Quality1 Image quality 1
Quality2 Image quality 2
Factory settings: Quality1
z JPEG
Set the resolution and quality settings for [JPEG(1)], [JPEG(2)], and
[JPEG(3)]. For details on settings for H.264 images, see "H.264(1) •
H.264(2) • H.264(3) • H.264(4)" (→ page 73).
<NOTE>
• Different resolutions must be selected for [JPEG(1)] to [JPEG(3)].
The same resolution cannot be selected for separate JPEG images.
Image capture size
Select from the following resolutions for the images to be displayed
when displaying JPEG images.
Setting value:
1920x1080/1280x720/640x360/320x180/160x90
Factory settings:
JPEG(1): 1920×1080
JPEG(2): 640×360
JPEG(3): 320×180
Image quality
Specify the JPEG image quality (2 types) for each resolution.
Setting value:
0 Super fine / 1 Fine / 2 / 3 / 4 / 5 Normal / 6 / 7 / 8 / 9 Low
Factory settings:
Image quality 1: 5 Normal
Image quality 2: 8
z H.264(1) • H.264(2) • H.264(3) • H.264(4)
Specify the [Max bit rate (per client)], [Image capture size], [Image
quality], and other settings for H.264 images.
For details on setting the JPEG images, see "JPEG" (→ page 73).
H.264 transmission
Whether to transmit the H.264 images is set here using On or Off.
Setting value:
On H.264 images are transmitted.
Off H.264 images are not transmitted.
Factory settings: On
<NOTE>
• When [On] has been selected as the [H.264 transmission] setting,
both H.264 images and JPEG images can be displayed on the live
screen [Live].
• When [On] has been selected as the [H.264 transmission] setting,
the JPEG image refresh interval may become slower.
/15fps /30fps
1 1 1
* * *
/25fps
1 1
* *
Internet mode (over HTTP)
This setting is selected when transmitting H.264 images over the
Internet.
H.264 images can be transmitted using the same broadband router
settings as when transmitting JPEG images.
Setting value:
On The H.264 images and audio are transmitted using the HTTP
port. For details on setting the HTTP port number, refer to
page 90.
Off The H.264 images and audio are transmitted using the UDP
port.
Factory settings: Off
<NOTE>
• When [On] is set, only [Unicast port (AUTO)] can be selected as the
[Transmission type] setting.
• When [On] is set, it takes a few seconds before the H.264 images
are displayed.
• When this is set to [On], H.264 images may not appear depending
on the number of users accessing the unit at the same time and
whether audio data exists.
• When this is set to [On], access will be limited to IPv4.
Image capture size
Select the resolution for H.264 images.
Selectable options will vary depending on the selected resolution
setting.
Setting value:
H264(1) 1920×1080
1280×720
H264(2) 1920×1080
1280×720
640×360
320×180
160×90
H264(3) 1280×720
640×360
320×180
160×90
H264(4) 1280×720
640×360
320×180
160×90
Factory settings:
H.264(1): 1920×1080
H.264(2): 640×360
H.264(3): 320×180
H.264(4): 160×90
Transmission priority
Set the transmission mode for H.264 images.
Setting value:
Constant bit rate Transmits H.264 images at the bit rate specified
in [Max bit rate (per client)].
Frame rate Transmit H.264 images at the frame rate specified
in [Frame rate].
Best effort Transmit H.264 images at a variable bit rate
between the maximum and minimum specified
in [Max bit rate (per client)], according to the
network bandwidth.
Advanced VBR Transmit H.264 images at the frame rate specified
in [Frame rate]. Images will be transmitted so
that the average transmission volume during the
duration specified in [Control time period] will be
the bit rate specified in [Max bit rate (per client)].
Factory settings: Frame rate
<NOTE>
• When [Transmission priority] is set to [Frame rate] or [Advanced
VBR], the number of users that can connect may decrease.
73