Table of Contents
Advertisement
DDX6034/6034M/6054/7034BT/7034BTM/714
DNX7000EX/7140/7240BT/7340BT
MICROCOMPUTER'S TERMINAL DESCRIPTION
Pin No.
Pin Name
57
VSS
58
NC (VALL_G)
59
VCC2
60
R_MIRROR_INT
R_CAM_INT
61
(RESERVE)
62
LED_ON
63
ILLUMI
TYPE_BT/DSP_
64
RST/DSP_RST
TYPE_BT/DSP_
64
RST/TYPE_BT
65
NC (CE)
66
TYPE1
67
INV_SW
68
INV_ENA
69
EJECT
70
SI
71
TILT_SPEED
72
TYPE3
73
JIG_EJECT
74
VCC2
TYPE_TV/ASEL/
75
ASEL
TYPE_TV/ASEL/
75
TYPE_TV
76
VSS
TYPE_DSP/
77
PTT_SW/PTT_SW
TYPE_DSP/PTT_
77
SW/TYPE_DSP
78
DISC_DET
79
BE_MREQ
80
BE_STBY
81
BE_CON
82
BE_INI
83
BE_RESERVE1
84
WRT_E2P
85
BE_PL_JUDGE
86
BE_RST
10
I/O
Application
Output is fi xed to L (Illumination control of the
O
variable illumi "G" when this terminal is used)
O
Mirror ON when the forced rear camera
O
Rear camera forced ON
O
Illumi ON/OFF of DISK slot
I
Illumi detection
O
8 functions: DSP RESET control
6 functions: Terminal used to detect if the
I
product destination needs BT or not.
I
Used for re-writing
I
Destination setting
O
Switching of inverter free run frequency
O
Back light ON/OFF control
I
Eject key input
O
SI control
Switching of tilt mechanism power supply
O
voltage
I
Terminal for K2 destination
Terminal for inspection mode (Can make Ejec-
I
tion even if the tilt mechanism is not connected)
8 functions:
O
Audio selector (sub) switching output
6 functions: Terminal used to detect if the
I
product destination needs TV I/F or not.
8 functions:
I
Detect if PTT SW is pressed or not.
6 functions: Terminal used to detect if the
I
product destination needs DSP or not.
Detect if the disc exists or not in DVD mecha-
I
nism
O
Request to backend
I
Standby request from backend
O
Control request to backend
O
Initial request to backend
O
Spare pin between B and E
I
Used for writing data in E2P
Terminal for operation identifi cation from back-
I
end
O
Reset request to backend
Truth Value
Processing/Operation/Description
Table
Not used. Output is fi xed to L
Hi: Mirror ON when the forced rear camera,
Lo: Mirror OFF when the forced rear camera
Hi: Forced rear camera change,
Lo: Normal operation
H: ON, L: OFF
L: ON, H: OFF
q
H: Reset release, L: Reset
q
H: BT is needed, L: BT is not needed
Fixed to Hi when used for re-writing
q
Refer to "Destination setting".
H: ON, L: OFF
L: When pressing of Key detected.
L: Turned on, H: Turned off
H: 8V, L: 5V
q
H: For K2 destination, L: To other destinations
L: Normal mode, H: Inspection mode
q
H: KAB, L: BT (Only for K TYPE)
q
H: TV is needed, L: TV is not needed
q
L: When pressing of Key detected.
q
H: DSP is needed, L: DSP is not needed
H: Disc does not exist, L: Disc exists
Presently not used. Output is fi xed to L.
Logic is not yet defi ned.
L: Normal, H: During writing data
H: Valid, L: Invalid
L: Reset, H: Reset clear
Hide quick links:
Advertisement
Table of Contents
