Measuring cup, Yogurt cup, Steam basket assy, Pan lid, Porridge scoop * For power cord replacement and product repairing, please contact the authorized service center of Panasonic. * The design and specifications are subjected to change without prior notice. - 3 -...
SR-TML500 / SR-TML510 / SR-TMS520 3. TROUBLESHOOTING GUIDE When receiving a rice boiler to be repaired, be sure to check that the main body is completely provide with the inner pan and the inner lid, ask the condition (phenomenon) of the trouble in detail. Before troubleshooting single parts, be sure to disconnect the power supply plug from the receptacle.
Page 7
SR-TML500 / SR-TML510 / SR-TMS520 Condition Troubleshooting Remedy • Excessive burning. Does the center thermostat operate (More than light brown) • Replace the center thermostat. properly? (Check with the evaporation test). • Seeing at Table 2. Are the parts on the P.C.B. mistake? Improper operation •...
Page 8
SR-TML500 / SR-TML510 / SR-TMS520 3.2 Table 2 Condition Troubleshooting Remedy • Rice is not boiling. • Replace the transformer. Is the transformer operating? (The indicating lamp does not come on) • Replace the P.C.B. complete. • Rice is not boiling.
SR-TML500 / SR-TML510 / SR-TMS520 4. TESTING PROCEDURE 4.1 Bubbling test Input the pan in the main body, lightly rotate the pan clockwise and counter clockwise to settle the pan on the heating plate properly. 1. Fill water until center area of the pan bottom is dipped and close the lid. Then turn on the boiling switch.
SR-TML500 / SR-TML510 / SR-TMS520 The above conditions are proper. Top view of pan Pan flange Holes on the tissue paper Tissue paper 4.3 Heat reserving test 1. Put approx. 1 liter of water and the thermometer [ repairing tool (mercury thermometer ASN-150H) ] in the pan, close the lid and turn on the boiling switch.
SR-TML500 / SR-TML510 / SR-TMS520 5. DISASSEMBLY 5.1 Hinge Cover removal 1. Remove the Dew Collector. 2. Remove the Hinge Cover mounting screws. 3. As show in the figure, insert a narrow flat head screwdriver from just below and pry off the Hinge Cover.
SR-TML500 / SR-TML510 / SR-TMS520 5.3 Control Unit A 1. Use screwdriver take off Hinge Cover. (PIC-1) 2. Pull out at Hinge Shaft. (PIC-2) 3. Pull out at Wiring of Lid Heater and then pull out Outer Lid Assy. (PIC-3)
SR-TML500 / SR-TML510 / SR-TMS520 5.4 Cast Heater and Thermostat Ass’y 1. Loosen a screw at cast heater. 2. Bending leg of thermostat. Screw PIC-1 3. Lift a thermostat. PIC-2 5.5 Side Heater 1. Pulling out a side heater and after that if will replace new side heater, keep a distance between 23 ~ 27 mm.
SR-TML500 / SR-TML510 / SR-TMS520 6. PARTS EXPLODED VIEW AND REPLACEMENT PARTS LIST 6.1 Parts Exploded View : Body (For TMS520) (For TMS520) (For TMS520) - 14 -...
SR-TML500 / SR-TML510 / SR-TMS520 Important safety notice : Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer’s specified part. 6.3 Replacement Parts List : SR-TML500, SR-TML510, SR-TML520 Parts List COUNTRIES / Q’TY REF.