Table Of Contents - HP 3300A Technical Manual

Section
I GENERAL INFORMATION ........................ 1-1
1-1. General.......................................... 1-1
1-5. Electronic Frequency Control ........ 1-1
1-7. Output System............................... 1-1
1-9. Instrument and Manual
Identification............................ 1-1
Section
II INSTALLATION.......................................... 2-1
2-1. Introduction.................................... 2-1
2-3. Initial Inspection............................. 2-1
2-5. Power Requirements..................... 2-1
2-7. Grounding Requirements .............. 2-1
2-10. Installation ..................................... 2-1
2-12. Bench Mounting ............................ 2-1
2-14. Rack Mounting .............................. 2-1
2-16. Repackaging for Shipment ............ 2-1
Section
III OPERATING INSTRUCTIONS .................. 3-1
3-1. Introduction.................................... 3-1
3-3. Controls and Indicators ................. 3-1
3-5. Turn On Procedure........................ 3-1
3-7. Operating Instructions ................... 3-1
Section
IV THEORY OF OPERATION ........................ 4-1
4-1. Introduction.................................... 4-1
4-3. General Description....................... 4-1
4-13. Schematic Theory ......................... 4-2
4-14. Frequency Control Network........... 4-2
4-17. Current Sources ............................ 4-2
4-19. Triangle Integrator ......................... 4-2
4-21. Voltage Comparator
Multivibrator ............................ 4-2
4-23. Sine Wave Synthesizer. ................ 4-2
4-25. Output Amplifiers........................... 4-2
4-27. Power Supply ................................ 4-3
4-30. Oven.............................................. 4-3
Section
V MAINTENANCE ......................................... 5-1
5-1. Introduction.................................... 5-1
5-3. Performance Checks..................... 5-1
5-5. Dial Accuracy................................. 5-1
5-7. Distortion Check ............................ 5-1
5-8. Frequency Response .................... 5-1
5-10. Maximum Output Level,
No Load .................................. 5-1
Number
1-1. Specifications ............................................. 1-0
5-1. Required Test Equipment........................... 5-0
5-2. Power Supply Adjustments......................... 5-3
5-3. Integrator Feedback Capacitance. ............. 5-7
TABLE OF CONTENTS (Continued)
Page
Section
V
Page
Page
Page
Section
VI
Page
Section
VII
Appendix
A
B
C
D
LIST OF TABLES
Page Number
5-4.
5-5.
5-6.
7-1.
7-2.
ii
MAINTENANCE (Cont'd)
5-13. Maximum Output Level,
Loaded.................................... 5-1
5-16. Square Wave Response ............... 5-2
5-18. Sync Output .................................. 5-2
5-19. Remote Frequency Control
Check ..................................... 5-2
5-20. Channel B-A Check ...................... 5-3
5-21. Adjustment and Calibration........... 5-3
5-22. Cover Removal ............................. 5-3
5-23. Power Supply Adjustments ........... 5-3
5-26. Power Supply Ripple Check.......... 5-3
5-27. Power Supply Regulation Check... 5-3
5-28. Oven Regulation. .......................... 5-3
5-29. Frequency Symmetry Adjust......... 5-3
5-32. Current Source Adjust................... 5-5
5-33. Dial Adjustment............................. 5-5
5-34. Dial Calibrate................................. 5-5
5-38. Distortion Adjust............................ 5-6
5-39. DC Output Level Adjust ................ 5-6
5-41. Square Wave Adjust ..................... 5-6
5-43. Repair Procedures. ....................... 5-6
5-44. Servicing Etched Circuit Boards ... 5-6
5-46. Servicing Rotary Switches ............ 5-7
5-48. Replacement of Factory
Selected Components ............ 5-7
5-50. Troubleshooting Procedure........... 5-7
5-54. Malfunction Isolation Plug ............. 5-7
5-56. Precautions ................................... 5-8
5-59. Troubleshooting Tree.................... 5-8
5-62. Troubleshooting Tables ................ 5-10
CIRCUIT DIAGRAMS ................................ 6-1
6-1. Introduction ................................... 6-1
6-3. Schematic Diagrams..................... 6-1
6-4. Component Location Diagrams .... 6-1
6-5. Plug-In Receptacle........................ 6-1
REPLACEABLE PARTS ............................ 7-1
7-1. Introduction ................................... 7-1
7-4. Ordering Information ..................... 7-1
7-6. Non-Listed Parts ........................... 7-1
References................................................. A-1
Not Applicable.
Not Applicable.
Maintenance Allocation.............................. D-1
Troubleshooting Aid ................................... 5-8
Maintenance Correlation Table.................. 5-10
Factory Selected Components................... 5-11
Replaceable Parts...................................... 7-2
Part No - National Stock
No. Cross Reference Index.................. 7-9
TM 11-6625-2495-14&P
Page
Page
Page
Page