Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
........................58 3.1.1.3 show device information ......................58 3.1.1.4 show env temperature ......................59 3.1.1.5 show hardware ........................59 3.1.1.6 show interface mtu ........................60 3.1.1.7 show interfaces ........................60 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 4
3.1.13.14 no negotiation......................... 96 3.1.13.15 shutdown ..........................96 3.1.13.16 no shutdown ........................... 97 3.1.13.17 speed ............................. 98 3.1.13.18 switchport ..........................99 3.1.13.19 no switchport .......................... 99 3.1.13.20 unicast-block ........................100 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 5
........................... 128 3.5.3.10 poe prio ..........................128 3.5.3.11 no poe prio ..........................129 NFC (SCALANCE XM-400 only) ..................130 3.6.1 The "show" commands ......................130 3.6.1.1 show nfc active status ......................130 SCALANCE XM-400/XR-500 Command Line Interface (CLI)
Page 6
Commands in the global configuration mode ..............152 5.2.2.1 ntp ............................152 5.2.3 Commands in the NTP configuration mode ................. 153 5.2.3.1 ntp server ..........................153 5.2.3.2 no ntp server ........................154 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 7
........................180 6.1.2.5 protocol-vlan ......................... 181 6.1.2.6 no protocol-vlan ........................182 6.1.2.7 subnet-vlan ........................... 183 6.1.2.8 no subnet-vlan ........................183 6.1.2.9 vlan............................184 6.1.2.10 no vlan ..........................185 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 8
..................219 6.3.2 clear spanning-tree detected protocols ................220 6.3.3 clear spanning-tree counters ....................221 6.3.4 Commands in the global configuration mode ..............221 6.3.4.1 spanning-tree ........................221 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 9
Network protocols ..........................259 IPv4 protocol ......................... 259 7.1.1 The "show" commands ......................259 7.1.1.1 show ip route ......................... 259 7.1.1.2 show ip static route ....................... 260 7.1.1.3 show ip gateway ........................261 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 11
7.5.3.1 ip dhcp relay circuit-id ......................329 7.5.3.2 no ip dhcp relay circuit-id ...................... 330 7.5.3.3 ip dhcp relay remote-id ......................330 7.5.3.4 no ip dhcp relay remote-id ....................331 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 12
..........................364 7.7.2.18 7.7.2.19 no snmp user ........................365 7.7.2.20 snmp view ..........................366 7.7.2.21 no snmp view ........................367 SMTP Client ......................... 367 7.8.1 The "show" commands ......................368 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 13
8.1.2.4 no gvrp ..........................391 IGMP snooping ........................391 8.2.1 The "show" commands ......................391 8.2.1.1 show ip igmp snooping ......................392 8.2.1.2 show ip igmp snooping forwarding-database ............... 392 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 14
................419 8.5.2 Commands in the global configuration mode ..............419 8.5.2.1 mac-address-table static unicast ..................420 8.5.2.2 no mac-address-table static unicast ..................421 Multicast ..........................421 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 15
Commands in the Router Configuration mode ..............451 9.2.3.1 ASBR Router ........................452 9.2.3.2 no ASBR Router ........................453 9.2.3.3 area range ..........................453 9.2.3.4 area range summary ......................455 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 16
..................... 501 9.3.1.5 show ipv6 ospf host ......................502 9.3.1.6 show ipv6 ospf interface ...................... 502 9.3.1.7 show ipv6 ospf neighbor ...................... 503 9.3.1.8 show ipv6 ospf redist-config ....................504 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 17
The "show" commands ......................549 9.4.1.1 show vrrp interface ........................ 549 9.4.1.2 show vrrp interface - vrid....................... 550 9.4.2 Commands in the Global Configuration mode ..............551 9.4.2.1 router vrrp ..........................551 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 18
9.5.5.13 vrrp timer ..........................589 9.5.5.14 no vrrp timer ......................... 590 RIPv2 (IPv4) ......................... 591 9.6.1 show ip rip ..........................591 9.6.2 Commands in the global configuration mode ..............592 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This Configuration Manual applies to the following software versions: ● SCALANCE XR-500 firmware as of version 5.1 ● SCALANCE XM-400 firmware as of version 5.1 Purpose of the Configuration Manual This Configuration Manual is intended to provide you with the information you require to install, commission and operate IE switches.
Page 28
Apart from this configuration manual, the products also have the following documentation: ● Configuration Manual: – SCALANCE XM-400/XR-500 Web Based Mangement This document is intended to provide you with the information you require to commission and configure IE switches using Web Based Management.
Siemens recommends strongly that you regularly check for product updates. For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept.
Page 30
You will find these documents on the product DVD in the following directory: /Open Source Information Trademarks The following and possibly other names not identified by the registered trademark sign ® registered trademarks of Siemens AG: SIMATIC NET, SCALANCE, C-PLUG, OLM SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Errors in the configuration can mean that no further operation is possible in the entire network. Note Command sets depend on the logged-on user. Changing configuration data is possible only with the "admin" role. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 32
2. Connect to the serial port of the device (baud rate 115200,data/parity/stop 8N1) 3. Enter your login and password. Note When you log in via a serial interface you can only log in with a local user account. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
It is not possible to modify parameters in this mode. To be able to modify configuration parameters, you need to change to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Protocol-based VLAN groups per port IPv4 subnet-based VLANs Multiple Spanning Tree instances Link aggregations or Etherchannels each with a maximum of 8 ports per aggregation Ports in a link aggregation SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 35
Rules for port ACL MAC Ingress and egress rules for port ACL MAC (total) Rules for port ACL IP Ingress and egress rules for port ACL IP (total) Rules for VLAN ACL IP SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 36
Per port, you can use 8 comparators for a transmission direction (ingress/egress). parameter requires 2 comparators the parameters each require one range comparator. The operator (equal) does not require any comparators. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Make sure, however, that names used by the operating system or other programs are correctly written. Blank To use blanks in a text, enter the text in quotes, for example "H e l l o" SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you use the keyword, you need to specify exactly one of the values "A", "B" or "C" keyword { [A] [B] [C] } After the keyword, enter one or more of the values "A", "B" or "C" SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● After a space, enter the number of the interface you assigned when you created it. – <port-channel-id(1-8)> – <vlan-id(1-4094)> You call port channels as follows: interface po 2 You call VLAN ports as follows: interface vlan 1 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 40
Available interface identifiers with SCALANCE XM-400 ● Interfaces of the basic device The interfaces of the basic device SCALANCE XM-400 are called module 1. ● Interfaces of extenders The port extenders are called module 2 and module 3 starting from the basic device. The number of port extenders depends on the number of ports of the basic device.
Page 41
Type of interface Command prompt cpu0 cli(config-if-cpu0)# vlan cli(config-if-vlan-$)# port-channel cli(config-if-po-$)# gigabitethernet cli(config-if-Gi$-$)# extreme-ethernet cli(config-if-Ex$-$)# Router-Port cli(config-RPort-Gi$-$)# The placeholders denote the numbering of the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● Multicast addresses Layer 2 multicast addresses as used on this device use the notation of MAC addresses. For permitted address ranges, check the rules or ask your network administrator. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Only endpoint of the communication Quality of service Type of Service (ToS) for The prioritization is specified in the header field "Traffic prioritization Class". Types of frame Broadcast, multicast, Multicast, unicast, anycast unicast SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 44
The DHCPv6 server delegates the distribution of IPv6 prefix- es to the DHCPv6 client. The DHCPv6 client is also known as PD router. Resolution of IP addresses in ARP (Address Resolution NDP (Neighbor Discovery Protocol) hardware addresses Protocol) SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Outside the local area network, the distinction between network ID and host ID is of no significance, in this case packets are delivered based on the entire IPv4 address. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Maximum permitted packet size on a path from a sender to a recipient. Path MTU discovery Mechanism for determining the maximum permitted packet size along the entire path from a sender to a recipient. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Structure of an IPv6 address IPv6 address format - notation IPv6 addresses consist of 8 fields each with four-character hexadecimal numbers (128 bits in total). The fields are separated by a colon. Example: fd00:0000:0000:ffff:02d1:7d01:0000:8f21 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 48
Prefixes and IPv6 addresses are specified in the same way as with the CIDR notation (Classless Inter-Domain Routing) for IPv4. Design IPv6 address / prefix length Example IPv6 address: 2001:0db8:1234::1111/48 Prefix: 2001:0db8:1234::/48 Interface ID: ::1111 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you exit the configuration mode and are then in the Privileged EXEC mode. Requirement You are in a configuration mode. Syntax Call the command without parameters: SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Example You are in the Interface configuration mode and you want to execute the write startup- command from the Privileged EXEC mode. config cli(config-if-$$)# do write startup-config SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The syntax of the command is displayed. Syntax If you call up help without parameters, you will obtain a list of all permitted commands in the current mode: help SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If the display is in pages, you cannot page back. You exit the page display with the key. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This is only possible if all the parts of the abbreviated input can be assigned to exactly one command or to the parts of the command. Example command can be replaced by the expression show event config sh e c SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
CLI#conf t; int vlan 1; no ip address dhcp; ip address 192.168.1.1 255.255.255.0; end; write startup has the same effect as: CLI#conf t CLI(config)#int vlan 1 CLI(config-if-vlan-1)#no ip address dhcp CLI(config-if-vlan-1)#ip address 192.168.1.1 255.255.255.0 CLI(config-if-vlan-1)#end CLI#write startup SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command deletes the last commands you entered. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# Syntax Call the command without parameters: clear history SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 56
Description 2.7 General CLI commands Result The last commands to be input are deleted. You display a list of the last 14 commands entered with the command. show history SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show cli-console-timeout Result The configuration for the timeout is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show device information Result The information about the device is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: show hardware Result The table of interface cards is displayed. The slot ID, the status and the type or name of the card is listed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The settings for the maximum transmission unit (MTU) of interfaces are displayed. 3.1.1.7 show interfaces Description This command shows the status and the configuration of one, several or all interfaces. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The status and the configuration of the selected interfaces are displayed. 3.1.1.8 show interfaces ... counters Description This command shows the counters of one, several or all interfaces. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the configuration of one, several or all IPv4 interfaces. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the configuration of one, several or all IPv6 interfaces. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the current PROFINET IO configuration. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The broadcast blocking settings for ports are displayed. 3.1.1.13 show unicast-block config Description This command shows the unicast blocking settings for ports. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the multicast blocking settings for ports. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameters have the following meaning: Parameter Description Range of values / note The destination is an IPv4 address ipv6 The destination is an IPv6 address Result The route is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you reset the counters of an interface. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you close a console session on the device. With the option, you close a session and that is not reacting. forceful-clear Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli# Syntax Call the command without parameters: configure terminal Result You are now in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With the commands you temporarily change the function rights of the enable disable logged in user, the login data remains unchanged. Description With this command, you change to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: lock Result The console is locked. The system expects the entry of the password. Further notes You cancel the lock by entering the Login password. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This allows you to check whether or not another node is reachable. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The messages relating to the response of the called node are displayed. 3.1.10 ping ipv6 Description With this command, you request a response from a device in the network. This allows you to check whether or not another node is reachable. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 75
Prefix of the sender timeout Response wait time If this time expires, the request is reported as "timed out". value Time until timeout 1 ... 100 s Default: 5 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result Result The tracing of the route is activated. Further notes You display the route with the command. show traceroute SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Enter a valid interface. interface-id Module no. and port no. of the interface For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
3.1.12.2 no interface Description With this command, you delete a logical interface. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
"keepalive" function. In this case, a packet is sent every 120 seconds that keeps the connection up. Requirement You are in the Global configuration mode. The command prompt is as follows: SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you disable the automatic logout. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no cli-console-timeout Result Automatic logout is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The height coordinate is created. 3.1.12.6 coordinates latitude Description With this command, you enter a latitude coordinate. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Input box for the longitude coordinate max. 32 characters To use spaces in the entry, enter the longitude coordinate in quotes: coordinates longitude "123 456" Result The longitude coordinate is created. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
3.1.12.9 system location Description With this command, you enter the location information for the system. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameter has the following meaning: Parameter Description Range of values / note string Input box for the name max. 255 characters Result The name is created in the system. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
1 number • Result The password is changed. Note Changing the password in Trial mode Even if you change the password in Trial mode, this change is saved immediately. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
<interface-name> The parameter has the following meaning: Parameter Description Range of values / note interface-name Name of the interface max. 63 characters Result The interface was assigned a name. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the blocking of broadcast frames on an interface. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameter assignment: broadcast-block Result Broadcast frames are blocked. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Optical connections are always operated in full duplex mode since they have a fiber for each transmission direction. With this command, you configure the duplex mode of an interface. The same mode must be set for connected interfaces. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you reset the duplex mode of an interface to the default value. The default value is full Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Default: enabled bled. Note Enabling both options When you call this command, you can only select one option. If you want to enable both options, call up the command again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you want to disable both options, call up the command again. Result Sending or receipt of LLDP packets is disabled. Further notes You enable the sending or receipt of LLDP packets with the command. lldp SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you attempt to configure a different port with this command, an error message will be displayed. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the mode of a combo port with the command and the parameter show interface description 3.1.13.10 Description With this command, you configure the size of the Maximum Transmission Unit (MTU) for an interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the blocking of multicast frames on an interface. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameter assignment: multicast-block SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable autonegotiation of connection parameters on an interface. Autonegotiation must be set for every interface of connected interfaces. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The automatic negotiation of connection parameters on an interface is deactivated. Further notes You enable the autonegotiation of connection parameters with the command. negotiation 3.1.13.15 shutdown Description With this command, you shut down the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you shut down an interface. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no shutdown Result The Interface is activated. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Transmission speed 10 Mbps Transmission speed 100 Mbps 1000 Transmission speed 1000 Mbps Result The transmission speed of the interface is configured. Further notes You disable autonegotiation with the command. no negotiation SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
2 functions. The router port is also called an IP interface. Requirement ● The interface is disabled with the command. shutdown ● You are in the Interface configuration mode. The command prompt is: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the blocking of unknown unicast frames on an interface. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameter assignment: unicast-block Result Unicast frames are blocked. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note that during the installation of a previous version, the configuration data can be lost. In this case, the device starts up with the factory configuration settings after the firmware has been installed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
File type Description Config Start configuration ConfigPack Detailed configuration information. for example, start configuration, users, certificates Debug This file contains information for Siemens Support. Firmware Firmware GSDML Information on the device properties HTTPSCert HTTPS certificate LogFile File with entries from the event log table Private MSPS MIB file "Scalance_w_msps.mib"...
The current configuration of the TFTP server for Load&Save is displayed. 3.2.2 load tftp Firmware The firmware is signed and encrypted. This ensures that only firmware created by Siemens can be downloaded to the device. Description With this command, you load the files from a TFTP server.
With this command, you save files on a TFTP server. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the LOADSAVE configuration mode with the command, you return to the Privileged EXEC mode. For information on the file types , refer to this list (Page 101). SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
3.2.5.2 password Description With this command, you activate and configure the password for a file. Requirement You are in the LOADSAVE configuration mode. The command prompt is as follows: cli(config-loadsave)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameters have the following meaning: Parameter Description Values showfiles Shows the available files filetype Shows that the file type follows that will be loaded filetype Name of the file type max. 100 characters SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The file types are displayed or the file type is assigned a name. Further notes With the " " command, you can display the file types. show loadsave files SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
3.2.5.5 tftp load Firmware The firmware is signed and encrypted. This ensures that only firmware created by Siemens can be downloaded to the device. Description With this command, you load a file from a TFTP server into the file system of the device. The TFTP protocol is used for the transfer.
3.2.5.7 tftp server Description With this command, you configure the access to a TFTP server. Requirement You are in the LOADSAVE configuration mode. The command prompt is as follows: cli(config-loadsave)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you restart the device. Select one of the following configuration settings: ● Device restart with the current configuration ● Device restart with the factory configuration settings. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The use of this command is required in the Trial mode. It can also be used in "auto save mode". Requirement ● The Trial mode is activated. ● You are in the Privileged EXEC mode. The command prompt is: *cli(...)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows configuration settings of the device. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 115
Secure Sockets Layer protocol Shows the configuration settings of the access control lists Shows the configuration settings of the Internet Protocol snmp Shows the configuration settings of the Simple Network Management Protocol SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 116
Some parameters cannot be changed. For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: auto-save As default the function is "enabled". Result The auto save function is enabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the status of this function and other information with the show device command. information You save changes to the configuration in the Trial mode with the write startupconfig command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you use the command without setting parameters, information about all PoE interfaces is displayed. For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The information for the selected PoE interface is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command you can set a value for the parameter "Maximum Power" for SCALANCE XM-400. This sets the maximum power that a PSE provides to supply PoE devices. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameters have the following meaning: Parameter Description Range of values / note integer Number of the PSE 1 … 4 Result The value for the maximum power is deleted. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you set the "Usage Threshold" parameter to the default value of 80%. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the Interface Configuration mode of a PoE interface. The command prompt is as follows: cli(config-if-Gi$-$)# The placeholders $-$ stand for the numbering of the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the Interface Configuration mode of a PoE interface. The command prompt is as follows: cli(config-if-Gi$-$)# The placeholders $-$ stand for the numbering of the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli(config-if-Gi$-$)# The placeholders $-$ stand for the numbering of the interface. Syntax Call the command without parameters: no poe custom maxpwr Result The user-defined maximum power is deleted. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You disable the use of the user-defined maximum power with the no poe custom maxpwr command. active 3.5.3.7 no poe custom maxpwr active Description With this command, you disable use of the user-defined maximum power for the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the Interface configuration mode of a PoE interface. The command prompt is as follows: cli(config-if-Gi$-$)# The placeholders $-$ stand for the numbering of the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The description of the corresponding device is deleted. 3.5.3.10 poe prio Description With this command, you specify the priority of the power supply for an interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The placeholders $-$ stand for the numbering of the interface. Syntax Call the command without parameters: no poe prio Result The priority of the corresponding interface has been set to "low". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows whether or not the NFC function (Near Field Communication) is activated or deactivated. Note You will find further information on NFC in the operating instructions "SCALANCE XM-400". Requirement You are in the User EXEC mode or in the Privileged EXEC mode.
With this command, you deactivate NFC. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: no nfc active SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 132
Further notes You activate NFC with the command. nfc active You display the status, i.e. whether the NFC function is activated or deactivated with the command show nfc active status SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show plug Result The current information of the C-PLUG or KEY-PLUG is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: plug Result You are now in the Plug Configuration mode. The command prompt is as follows: cli(config-plug)# Further notes You exit the Plug Configuration mode with the command. exit SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The device configuration on the C-PLUG or KEY-PLUG is deleted. 4.1.3.2 write Description With this command, you format the C-PLUG or KEY-PLUG and copy the current device configuration to it. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show web-session-timeout SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The time is configured and automatic logout is enabled. Further notes You disable automatic logoff with the command. no web-session-timeout You display the current timeout setting with the command. show web-session-timeout SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● When display mode A "port status" is displayed, and the button is pressed for more than 12 seconds, there is a restart with the factory settings. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameters have the following meaning: Parameter Description Range of values / note enable enables the function for setting the fault Default: enabled mask disable disables the function for setting the fault mask SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
4.4.2.2 signaling-contact status Description With this command, you close or open the signaling contact. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 143
Signaling contact is opened. close Signaling contact is closed. Result The signaling contact is opened or closed. Further notes You display the setting with the command. show signaling contact SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 144
Functions specific to SCALANCE 4.4 Signaling contact SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows all the entries for daylight saving time stored on the device. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure the way in which the system time is obtained. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
5.1.2.2 time set Description With this command, you set the system clock. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure the start and end of daylight saving time. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure the start and end of daylight saving time with a generic description. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you do not specify a name as the parameter, all entries are deleted. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ntp info Result The current NTP settings are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: Result You are now in the NTP configuration mode. The command prompt is as follows: cli(config-ntp)# Further notes You exit the NTP configuration mode with the command. exit SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Value for the time in seconds 64 … 1024 For information on identifiers of addresses and interfaces, refer to the section "Addresses and interface identifiers (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure the time difference between the device and the NTP server. Requirement You are in the NTP configuration mode. The command prompt is as follows: cli(config-ntp)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show sntp status SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show sntp unicast-mode status SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: sntp Result You are now in the SNTP configuration mode. The command prompt is as follows: cli(config-sntp)# Further notes You exit the SNTP configuration modewith the command. exit SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the settings for the unicast mode with the show sntp unicast-mode status command. You display the settings for the broadcast mode with the show sntp broadcast-mode status command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Default: no time difference Result The time zone of the system time is configured. Further notes You can display the settings of this function and other information with the show sntp command. status SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Further notes You can reset the setting to the default with the command. no sntp unicast-server You display this setting and other information with the show sntp unicast–mode status command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The following devices support time-of-day synchronization using PTP: ● SCALANCE XR528-6M ● SCALANCE XR552-12M This section describes commands relevant for configuration of the Precision Time Protocol according to IEEE 1588. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no ptp Result The Precision Time Protocol is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command you change to the PT Transparent Clock configuration mode. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: ptp transparent-clock configuration SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With end-to-end synchroniza- parent clock. tion with more than 2 slaves, freak values > 100 ns can oc- cur in the offset. peer-to-peer The device operates as a peer-to-peer trans- parent clock. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
<domain-id(0-255)>} The parameter has the following meaning: Parameter Description Range of values / note domain-id The identifier of the primary domain. 0 ... 255 Result The primary domain is specified. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
(standby connection) VLAN This section describes commands for configuring and managing virtual networks (VLANs). 6.1.1 The "show" commands This section describes commands with which you display various settings. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The entries of the MAC addresses table are displayed. 6.1.1.2 show mac-address-table dynamic multicast Description This command shows the table with the dynamic multicast MAC addresses assigned by the device. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the table with the dynamic unicast MAC addresses assigned by the device. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the table with the static multicast MAC addresses. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the table with the static unicast MAC addresses. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you show the number of MAC addresses for all or a selected VLAN. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". If you do not select any parameter from the parameter list, all entries are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The information for the selected VLAN is displayed. 6.1.1.9 show vlan device info Description This command shows all the global information that is valid for all VLANs. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you do not select any parameter from the parameter list, the entries of all available interfaces are displayed. Result The settings for the automatic learning of addresses are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command displays the table with the protocol group entries. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you can put several interfaces or the interfaces of VLANs together and configure them together. The configurations are valid for all interfaces of the specified range. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you remove the interfaces or interfaces of VLANs from the interface range or break it up if you first remove all previously added interfaces. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
6.1.2.3 map protocol Description With this command, you assign a protocol to a protocol group. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you delete a protocol from all protocol groups. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
6.1.2.5 protocol-vlan Description With this command, you enable the protocol-based classification on all interfaces. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The classification is disabled. Further notes You enable the setting with the command. protocol-vlan You can display the status of this function and other information with the show vlan device command. info SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you disable IPv4 subnet-based VLAN on all interfaces. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no subnet-vlan SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Do not enter any leading zeros with the number of the VLAN. Result The VLAN is created. You are now in the VLAN configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display information about the VLAN with the command. show vlan 6.1.2.11 vlan range Description With this command, you can select several VLANs and configure them together. The configurations are valid for all selected VLANs. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The subnet with subnet mask and subnet address is assigned to a VLAN. Further notes You cancel the setting with the command. no map subnet You can display the status of this function and other information with the show subnet-vlan command. mapping SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
6.1.3.3 switchport acceptable-frame-type Description With this command, you configure which types of frames are accepted. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The interface accepts tagged and untagged frames. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no switchport acceptable-frame-type SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Further notes You can reset the setting to the default with the command. no switchport access vlan You display the setting and other information with the command. show vlan port config SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you assign the protocol group and a VLAN to an interface. Requirement ● The protocol group is configured. ● You are in the Interface configuration mode .The command prompt is: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
<group id(0-2147483647)> The parameter has the following meaning: Parameter Description Range of values / note group id Number of the group 0 ... 2147483647 Result The assignment is deleted. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
" command acceptable frame-type all at the trunk port, the port also receives untagged frames. hybrid Configures the port as a hybrid port that accepts tagged and Default: hybrid untagged frames. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure the operating mode with the command. switchport mode You display this setting and other information with the command. show vlan port config You configure the interface as a switch port with the command. switchport SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you reset the priority default for the interface to the default value. The default value is 0. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can reset the setting to the default with the command. no switchport pvid You configure the VLAN ID with the command. switchport access vlan You display the setting and other information with the command. show vlan port config SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the status of this function and other information with the show vlan port command. config 6.1.3.15 tia interface Description With this command, you enable or disable the property TIA interface. The interface can be used for PNIO. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The interface is added permanently to the list of incoming and outgoing connections. Tagged and untagged frames are transferred. ● Untagged Port The interface transfers untagged frames. If the VLAN ID (PVID) is set, incoming untagged SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 199
The command prompt is as follows: cli(config-vlan-$$$)# Syntax Call up the command with the following parameters: ports [<interface-type><0/a-b,0/c,...>] [<interface-type><0/a-b,0/c,...>] [port-channel<a,b,c-d>] untagged<interface-type> <0/a-b,0/c,...> [<interface-type><0/a-b,0/c,...>] [port-channel <a,b,c-d>] [all] forbidden<interface-type><0/a-b,0/c,...> [<interface-type><0/a-b,0/c,...>] [portchannel<a,b,c-d>] [name<vlan-name>] SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
6.1.4.2 no ports Description With this command, you remove ports from a VLAN. Requirement You are in the VLAN configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 201
32 characters For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The ports are removed from the VLAN configuration. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The VLAN is assigned a name. Further notes You delete name assignment for a VLAN with the command. no name 6.1.4.4 no name Description With this command, you delete the name assignment for a VLAN. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● Other frames are forwarded according to the normal VLAN rules and a transparent port behaves like an untagged member in this VLAN. Requirement You are in the VLAN configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● All transparent ports become untagged members in this VLAN ● The port VLAN ID of the previous transparent ports remains set to the ID of this VLAN. ● All other ports remain marked as forbidden in this VLAN. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Specification of the protocol set for a Channel-Group If you do not select any parameters from the parameter list, the settings of all channels will be displayed in detail. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If the port in the link aggregation becomes active, individual port configurations such as DCP forwarding are overwritten with the configured values of the link aggregation. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can reset the setting for the load balancing policy to the default with the no port-channel command. load-balance You can display the status of this function and other settings with the show etherchannel command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The Etherchannel is configured. 6.2.3.2 no channel-group Description With this command, you remove the interface from an Etherchannel. Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the settings of the spanning tree function. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Common Internal Spanning Tree (CIST) instance or a selected instance of the Multiple Spanning Tree Protocol. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli> cli# Syntax Call up the command with the following parameters: show spanning-tree active [detail] The parameter has the following meaning: Parameter Description detail Shows settings in detail SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Shows detailed information about the spanning tree settings of the interface Result The settings for the spanning tree function of the bridge are displayed. 6.3.1.5 show spanning-tree detail Description This command shows the detailed settings of the spanning tree function. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the settings of the ports for the spanning tree function. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
MAC address and the status of L2GP are displayed. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the settings of the root bridge for the spanning tree function. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show spanning-tree mst configuration Result The settings of an instance of the Multiple Spanning Tree protocol are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Shows detailed information about the selected interface For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The port-specific settings are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
(Page 39)". If you do not select any parameters from the parameter list, the process is restarted for all interfaces. Result The connection settings for spanning tree are renegotiated. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the spanning tree function. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the status of this function and other information with the show spanning-tree command. detail You can display information about active ports with the show spanning-tree active command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the status of this function and other information with the show spanning tree command. detail You can display information about active ports with the show spanning tree active command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The bridge with the highest priority becomes the root bridge. The lower the value, the higher the priority. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you reset the priority of the device back to the default value. The default value is 32768. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli(config)# Syntax Call the command without parameters: spanning-tree mst configuration Result You are now in the MSTP configuration mode. The command prompt is as follows: cli(config-mst)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you reset the maximum number of hops that a path in an MST can run through to the default value. The default value is 20. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command you specify whether the device is a root bridge (primary) or a substitute root bridge (secondary). Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you disable the "root bridge" function on the device. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
BPDUs max-age becomes invalid. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 231
All rime settings are reset. You display these settings and other information with the commands that start with show spanning-tree ... SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 232
The selected setting for the time is reset to the default value. Further notes You configure the time with the command (time settings). spanning-tree You display these settings and other information with the commands that start with show spanning-tree ... SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 234
With each call of the command, you can configure precisely one property. If you want to configure several properties, call the command several times. Result The selected property is configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The connection is configured as full-duplex • shared in all other cases portfast disabled port-priority Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● With the option, you disable the interface for the Multiple Spanning Tree function. disable Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 237
You can reset the setting to the default with the (properties) command. no spanning-tree mst You display these settings and other information with the commands that start with show spanning tree ... SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With each call of the command, you can configure precisely one property. If you want to configure several properties, call the command several times. Result The selected setting is reset to the default value. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you disable automatic discovery of a bridge connected to the interface. Requirement You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note enabled BPDU packets are transmitted at the Default: enabled port disabled BPDU packets are not transmitted at the port Result The BPDU transmit status has switched over. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the status of this function and other information with the show spanning-tree command with the option. interface detail 6.3.5.9 spanning-tree bpdufilter Description With this command, you configure the BPDU transmit status for a port. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the Interface Configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: spanning-tree layer2-gateway-port Result The port is configured as a layer 2 gateway port. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description This function prevents alternative ports or root ports becoming designated ports if there is a disruption of a one-way link. With this command, you enable the function. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you disable the function. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no spanning-tree loop-guard SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The port is prevented from adopting the role of root port. Further notes You cancel the lock with the command. no spanning-tree restricted-role You can display the status of this function and other information with the show spanning-tree command. detail SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The port cannot initiate any modifications to the network topology. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: spanning-tree restricted-tcn SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure the Hello time after which the bridge sends its configuration frames (BPDUs). A change to this value applies to all MST instances active on this interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The default value is 2 seconds. Requirement You are in the interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no spanning-tree mst hello-time SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Keyword for the pseudoroot unicast MAC address ucast_mac MAC address of the interface aa:aa:aa:aa:aa:aa Default: MAC address of the device You can only change the value for the priority in the steps of 4096. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The pseudoroot MAC address and the priority are rest to the defaults. Further notes You configure the settings with the command. spanning-tree mst pseudoRootId You display this setting and other information with the commands that start with show spanning tree ... SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of VLANs assigned to an in- enter the range limts with a hy- stance phen or blank Result The range of VLANs is assigned to the MST instance. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The assignment of a VLAN to an MST instance is canceled or the MST instance is deleted. Further notes You assign a VLAN to an MST instance with the command. instance You display this setting and other information with the show spanning-tree mst command. configuration SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The default value is: ● The MAC address of the device is configured as name. Requirement You are in the MSTP Configuration mode. The command prompt is as follows: cli(config-mst)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The MST region is assigned a revision number. Further notes You delete a revision number with the command. no revision You display this setting and other information with the show spanning tree mst command. configuration SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Passive Listening 6.4.1 The "show" commands This section describes commands with which you display various settings. 6.4.1.1 show passive-listening Description This command shows whether or not "passive listening" is enabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
"Passive listening" can only be enabled when MSTP is disabled. You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: passive-listening Result The "passive listening" function is enabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The "passive listening" function is disabled. Further notes You enable "passive listening" with the command. passive-listening You display the status of "passive listening" with the command. show passive-listening SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the routes currently being used. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip static route Result The static routes are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip telnet Result The admin status and the port number of the Telnet server are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows an overview of the DCP forwarding behavior on one or all interfaces. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip dns Result Information on the DNS client is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip dns name-server SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. 7.1.2.1 ip route Description With this command, you configure a static entry in the IP routing table. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you delete a static entry from the IP routing table. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. DHCP must not be enabled on any IP interface. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no ip routing Result IPv4 routing is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command you stop the network node reacting to ping queries. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The Telnet server is enabled. Further notes You disable the Telnet server with the command. no telnet-server 7.1.2.8 no telnet-server Description With this command, you disable the Telnet server. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameters have the following meaning: Parameter Description Range of values / note read-only only reading is permitted on the DCP server read-write reading and writing is permitted on the Default: read-write DPC server SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
7.1.2.11 ip domain lookup Description This command enables the DNS client of the device. To be able to use the function, a DNS server must be reachable. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no ip domain lookup Result The DNS client of the device is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The IP address and, if specified, the index for a DNS server have been set. 7.1.2.14 no ip name server Description With this command, you delete required DNS server. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. 7.1.3.1 ip address Description With this command, you assign an IPv4 address or an IPv4 subnet to the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 276
If you configure the interface via which you access the device, the connection will be lost! Further notes You delete the IPv4 address with the command. no ip address You display this setting and other information with the command. show ip interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the assignment of an IPv4 address to an interface and disable DHCP. Requirement You are in the Interface configuration mode of VLAN or a router port. The command prompt is as follows: cli(config-if-vlan-$$$)# or with a router port: cli(config-RPort-if-Int$-$) SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 278
You configure the static IPv4 address with the command. ip address You display this setting and other information with the command. show ip interface You enable DHCP with the command. ip address dhcp SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The forwarding behavior of the interface for DCP frames is configured. IPv6 protocol This section describes the commands relevant for working with IPv6. 7.2.1 clear ipv6 traffic Description With this command, you reset the statistics counters to zero. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ipv6 neighbors Result The IPv6 neighbors table is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ipv6 route SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the statistics for UDP and ICMPv6 for the corresponding interface. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the routes that were generated statically. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure a static entry in the IPv6 neighbors table. Requirement ● The neighbor node is located on the same link. ● You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete an entry from the IPv6 neighbor table. Requirement ● The neighbor node is located on the same link. ● You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure maximum packet size (MTU). The setting is only effective if PMTU Discovery is enabled. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command you disable the use of the maximum packet size. In other words, the setting is no longer used with the PMTU Discovery function. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The PMTU Discovery function is enabled. Further notes You disable the PMTU Discovery function with the command no ipv6 path mtu discover You display the settings with the command. show ipv6 pmtu SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure a static entry in the IPv6 routing table. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 290
Further notes You delete a static entry from the IPv6 routing table with the command. no ipv6 route You display the IPv6 routing table with the command. show ipv6 route SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Enter a valid interface. interface-id Module no. and port no. of the interface For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result IPv6 routing is enabled. Further notes You disable the IPv6 routing with the command. no ipv6 unicast-routing You display the IPv6 routing table with the command. show ipv6 route SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Interface ID according to the EUI-64 eui-64 method linklocal Link local address For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the IPv6 address. Requirement ● IPv6 is activated ● The interface is an IP interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
). When this function is enabled, the DHCPv6 client becomes the PD router. You can also change the prefix name. The requirement is that the prefix is not used by a PD sub-client interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 297
You show the setting with the command. show ipv6 dhcp interface You can display the statistics of the DHCPv6 client with the show ipv6 dhcp client command. statistics SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the statistics of the DHCPv6 client with the show ipv6 dhcp client command. statistics 7.2.4.5 no ipv6 address dhcp Description With this command, you delete the IPv6 address and disable DHCPv6. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you assign a link local address to the interface. Requirement ● IPv6 is activated ● The interface is an IP interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the link local address. Requirement ● IPv6 is activated ● The interface is an IP interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# Requirement You are in the Interface configuration mode of VLAN. The command prompt is as follows: cli(config-if-vlan-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call up the command with the following parameters: ipv6 interface-identifier <prefix> The parameter has the following meaning: Parameter Description Range of values / note prefix Interface ID Enter an interface ID. Maximum 64 bits SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The interface ID has been deleted. Further notes You configure the interface ID with the command. ipv6 interface-identifier You display this setting and other information with the command. show running-config SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display this setting and other information with the command. show ipv6 interface 7.2.4.12 ipv6 nd suppress-ra Description With this command, you disable the distribution of IPv6 router advertisement packets. As default, the router advertisements are disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The interface is an IP interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# Syntax Call the command without parameter assignment: no ipv6 nd suppress-ra SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ip dhcp client stats Result The counters are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the DHCP config file request option. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: no ip dhcp config-file-request Result The DHCP config file request option is disabled. Further notes You enable the DHCP config file request option with the ip dhcp config-file-request command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The registration mode of the DHCP client is configured. DHCPv6 client (IPv6) This section describes commands for DHCPv6. 7.4.1 The "show" commands This section describes commands with which you display various settings. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the DHCPv6 configuration and the DHCPv6 information that was received from the DHCPv6 server. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the Privileged EXEC mode. The command prompt is as follows: cli# Syntax Call the command without parameter assignment: show ipv6 dhcp pd sub-client interfaces Result The information is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Password for the HMAC algorithm MD5 Enter a valid password. 1 ... 64 key-id Keyword for the ID of the password value ID of the password Enter a valid ID. 0 ... 4294967295 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Length of the interval in seconds 600 ... 4294967295 Default: 4294967295 (24 hours) Result The interval is specified. When the time elapses, the DHCPv6 client sends an information request message to refresh the configuration parameters. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure the interface as a router port with the command. no switchport You display the setting with the command. show ipv6 dhcp You configure the interval with the command. ipv6 dhcp client information refresh minimu SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Name of the vendor-specific configuration Enter the required name. 1 ... 128 characters Result The setting is configured. Further notes You disable the setting with the command. no ipv6 dhcp client option SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If the option "DHCP reconfig-accept" is set, the DHCPv6 client accepts the reconfiguration message. This is assuming that it contains the correct reconfiguration key. Via this key, the DHCP client identifies the DHCPv6 server SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The interface is an IP interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# Syntax Call the command without parameters: no ipv6 dhcp client reconfig-accept SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
IPv6 address of the SNTP server address option Keyword for the option code code Number of the DHCPV6 option Enter the required number. 1 ... 200 Result The setting is configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Specify the required ID of the DHCPv6 option. 1 ... 100 Result The required configuration parameter is removed. Further notes You configure the request with the command. ipv6 dhcp client request SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the setting with the command. show ipv6 dhcp interface 7.4.2.11 ipv6 dhcp client-id interface Description With this command, you specify which IP interface uses a DUID of the type SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
DHCPv4 Relay Agent (IPv4) This section describes commands for the DHCP Relay Agent. 7.5.1 The "show" commands This section describes commands with which you display various settings. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command displays the DHCP relay agent settings for all or for a selected VLAN. Requirement You are in the User EXEC mode or in the Privileged EXEC mode or in the Global configuration mode. The command prompt is as follows: cli> cli# cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can specify up to four IP addresses for the DHCP relay agent. Requirement ● You are in the Global configuration mode. The command prompt is: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
<ip address> The parameter has the following meaning: Parameter Description Range of values / note ip address IP address of the DHCP server Enter the IP address to be delet- SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The router index is added to the Circuit Default setting vlanid The VLAN ID is added to the Circuit ID. - recv-prot The Circuit ID is added to the receiving port. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure the content of the information with the ip dhcp relay circuit-id option command. You can display the status of this option and other information with the show ip dhcp relay command. information SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
DHCP query to DHCP servers located in a different subnet. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: service dhcp-relay SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable the DHCP Relay Agent with the command. service dhcp-relay You can display the status of this function and other information with the show ip dhcp relay command. information SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You remove the Circuit ID with the command. no ip dhcp relay circuit-id You display the IP addresses with the command. show dhcp server You display the settings with the command. show ip dhcp relay information SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you specify the device ID. Requirement ● The interface is an IPv4 interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# Syntax Call the command without parameter assignment: no ip dhcp relay remote-id Result The device ID is removed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". If you do not select any parameter, the entries are displayed for all available interfaces. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". If you do not specify any parameters, the counter is reset on all interfaces. Result The counters are reset. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameters have the following meaning: Parameters Description Range of values / note enable Remote ID is used disable Remote ID is not used Result The Remote ID is activated. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
DHCPv6 server can be reached Requirement ● The interface is an IPv6 interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the statistics with the command. show ipv6 dhcp relay statistics 7.6.4.2 no ipv6 dhcp relay Description With this command, you disable the DHCPv6 relay agent. You can also remove the DHCPv6 servers. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 337
You configure the interface as a router port with the command. no switchport You display the setting with the command. show ipv6 dhcp interface You display the statistics with the command. show ipv6 dhcp relay statistics SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable the DHCPv6 relay agent with the command. ipv6 address dhcp You enable the remote ID with the command. ipv6 dhcp relay remote-id. You configure the interface as a router port with the command. no switchport SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure the remote ID type with the command. ipv6 dhcp relay remote-id type 7.6.4.5 ipv6 dhcp relay remote-id userDefined Description With this command, you configure a designation for the remote ID. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
SNMP This section describes commands of the Simple Network Management Protocol (SNMP). 7.7.1 The "show" commands This section describes commands with which you display various settings. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show snmp community Result The details of the configured SNMP communities are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show snmp filter Result The configured SNMP filters are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show snmp group access Result The rights of the configured SNMP groups are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show snmp notif Result The configured SNMP notification types are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show snmp targetparam Result The configured SNMP target parameters are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show snmp user Result The settings for the SNMP user are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Privileged EXEC mode again. 7.7.2.1 snmpagent Description With this command, you enable the SNMP agent function. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable the SNMP agent function with the command. snmpagent 7.7.2.3 snmp agent version Description With this command, you configure whether all SNMP queries or only SNMPv3 queries are processed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
7.7.2.4 snmp access Description With this command, you configure the access to an SNMP group. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 350
The keywords need to be specified. If optional parameters are not specified when configuring a group, the default value will be used. Result The settings for access to an SNMP group are configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Selects the version of the protocol • used • • Authentication Selects the authentication method: • auth • noauth • priv Result The access to an SNMP group is deleted. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The settings are lost after a restart (non-volatile): • nonvolatile The settings are retained after a restart If optional parameters are not specified when configuring a community, the default values apply. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You show the details of an SNMP community with the command. show snmp community You show the status information of the SNMP communication with the command. show snmp SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You delete the details of an SNMP group with the command. no snmp group You display the created SNMP groups with the command. show snmp group You display the created SNMP user with the command. show snmp user SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the created SNMP user with the command. show snmp user 7.7.2.10 snmp notify Description With this command, you configure the details of the SNMP notifications. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the configured SNMP target addresses with the show snmp targetaddr command. 7.7.2.11 no snmp notify Description With this command, you delete the details of the SNMP notifications. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure the SNMP target address. Requirement ● The SNMP target parameters are configured. You are in the Global configuration mode. The command prompt is: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 358
1 ... 65535 For information on addresses and interfaces, refer to the section "Addresses and interface names (Page 39)". If optional parameters are not specified when configuring, the default values apply. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The SNMP target address is deleted. Further notes You change the SNMP target address with the command. snmp targetaddr You display the SNMP target address with the command. show snmp targetaddr SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: snmp targetparams <ParamName> user <UserName> security-model {v1|v2c|v3{auth|noauth|priv}} message-processing {v1|v2c|v3}[{volatile|nonvolatile}] SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 361
The settings are retained after a restart Keywords need to be specified. If optional parameters are not specified when configuring, the default values apply. Result The SNMP target parameters are configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The SNMP target parameters are deleted. Further notes You change the SNMP target parameters with the command. snmp targetparams You display settings of this function with the command. show targetparam SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable write access for SNMPv1 and SNMPv2 PDUs. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no snmp v1-v2 readonly SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The default settings are used after a restart (non-volatile): • nonvolatile The saved settings are used after a restart If optional parameters are not specified when configuring an SNMP user, the defaults values apply. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The details of the SNMP user are deleted. Further notes You change the settings with the command. snmp user You display the configured users with the command. show snmp user SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
(non-volatile): • nonvolatile The settings are retained after a restart (default) If optional parameters are not specified when configuring, the default values apply. Result The SNMP view is configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure a view with the command. snmp view You display the configured view trees with the command. show snmp viewtree SMTP Client This section describes commands of the Simple Mail Transfer Protocol (SMTP). SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show events sender email SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the EVENTS configuration mode with the command, you return to the Privileged EXEC mode. 7.8.2.1 smtp-server Description With this command, you configure an entry for an SMTP server. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
7.8.2.2 no smtp-server Description With this command, you delete an SMTP server entry. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call up the command with the following parameters: sender mail-address <mail-address> The parameter has the following meaning: Parameter Description Range of values / note mail-address Email name of the sender max. 100 characters SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you send an e-mail according to the currently configured SMTP settings. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result An SMTP port is configured. Further notes You can reset the setting to the default with the command. no smtp-port You display the setting with the command. show smtp-port SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
7.9.1 The "show" commands This section describes commands with which you display various settings. 7.9.1.1 show ip http server status Description This command shows the status of the HTTP server. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable HTTP on the device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: ip http As default the function is "enabled". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the setting of this function and other information with the show ip http command. server status You enable HTTP with the command. ip http 7.10 HTTPS server This section describes commands of the Hypertext Transfer Protocol Secure (HTTPS). SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ssl server-cert SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you display the IP ARP table. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. 7.11.2.1 Description With this command, you generate a static entry in the ARP cache. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the status of this function and other information with the show ip arp command. You configure the router port with the command. no switchport 7.11.2.2 no arp Description With this command, you delete an entry from the ARP cache. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure the timeout setting of the ARP cache. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no arp timeout Result The timeout setting for the ARP cache is reset to the default value. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you disable the SSH protocol on the device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no ssh-server SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 385
Network protocols 7.12 SSH server Result The SSH protocol is disabled on the device. Further notes You enable the SSH protocol with the command. ssh-server SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 386
Network protocols 7.12 SSH server SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show forward-all Result The entries of the GMRP forward all table are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the GMRP function for all or individual interfaces on the device. Requirement You are in the Global configuration mode You are in the Interface configuration mode The command prompt is as follows: cli(config)# cli (config-if-$$$) # SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: no gmrp Result In the Global configuration mode: The GMRP function is disabled on the device. In the Interface configuration mode: The GMRP function is disabled for this interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you want to disable the function for a specific interface on the device, use the no gvrp command. You can display the status of this function and other information with the show vlan device command. info SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
IGMP snooping This section describes the snooping functionality of the Internet Group Management Protocol. 8.2.1 The "show" commands This section describes commands with which you display various settings. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the multicast forwarding entries for all or a selected VLAN. Requirement ● IGMP snooping is enabled on the device ● You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Number of the addressed VLAN 1 ... 4094 For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The statistical information is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
There is no separate show command to display the version of IGMP used by the device. This information is shown when you enter the command in the User show ip igmp snooping EXEC mode or in the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: ip igmp vlan-snooping Result IGMP snooping is enabled for all VLANs. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you delete the counters for all or a selected VLAN. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Address of the source Specify a valid IP address. Default: 0.0.0.0 For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can reset the setting to the default with the no ip igmp snooping port-purge-interval command. You can display the status of this function and other information with the show ip igmp command. snooping globals SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the VLAN Configuration mode with the command, you return to the Global exit Configuration mode. ● If you exit the VLAN Configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you delete a static IGMP entry. Requirement You are in the VLAN Configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure the IGMP snooping switch as querier. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Further notes You configure the setting with the command. ip igmp snooping querier You can display the status of this function and other information with the show ip igmp command. snooping SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
8.4.1 clear hrp counters Description With this command, you reset the HRP counters. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you reset the counters of the standby function. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show hrp counters Result The counters are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show ring-redundancy manager counters SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result You are now in the Redundancy Configuration mode. The command prompt is as follows: cli(config-red)# Further notes You exit the Redundancy Configuration mode with the command. exit SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you disable the ring redundancy function on a device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The standby function is enabled. Further notes You disable the setting with the command. no ring-redundancy standby You can display the status of this function and other information with the show ring- command. redundancy SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Redundancy Configuration mode with the command, you return to the exit Global Configuration mode. ● If you exit the Redundancy Configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Note Differing port addresses The first and second port must be configured on different interfaces Result The ports of the ring redundancy are configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the name of a standby connection. Requirement You are in the Redundancy Configuration mode. The command prompt is as follows: cli(config-red)# Syntax Call the command without parameters: no standby connection-name SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you disable the standby force-master function. Requirement ● HRPis enabed ● You are in the Redundancy configuration mode. The command prompt is: cli(config-red)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Module no. and port no. of the interface For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The ports for a standby connection are configured and enabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The ports for a standby connection are disabled. Further notes You enable the setting with the command. standby port You display the status of this function and other information show ring-redundancy SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the Redundancy configuration mode. The command prompt is as follows: cli(config-red)# Syntax Call the command without parameters: no standby wait-for-partner SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Enter a valid interface interface-id Module no. and port no. of the interface For information on names of interfaces and addresses, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
(Page 39)". If you do not select any parameter from the parameter list, the entries are displayed for all available interfaces. Result The dynamic unicast MAC addresses are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The entry in the forwarding database is generated. Further notes With the command, you display the list of show mac-address-table static unicast configured entries. With the command, you delete an entry. no mac-address-table static unicast SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The commands in this section configure the procedures for handling Multicast frames. The commands allow the following: ● Configuration of groups ● IGMP/MLD ● GMRP ● Blocking unknown Multicast frames. With the "show" commands, you can display the configuration data. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The multicast blocking settings for ports are displayed. 8.6.1.2 show mac-address-table dynamic multicast Description This command shows the table with the dynamic multicast MAC addresses assigned by the device. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the table with the static multicast MAC addresses. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure static multicast addresses that will be blocked. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
<vlan-id(1-4094)> 8.6.2.2 mac-address-table static multicast Description With this command, you configure a static multicast address. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
8.6.2.3 no mac-address-table static multicast Description With this command, you delete a static multicast address. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the information about MLD snooping for all or a selected VLAN. Requirement ● MLD snooping is enabled. ● You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note vlan Keyword for a VLAN connection vlan id Number of the addressed VLAN 1 ... 4094 If you specify VLAN, the configuration of all VLANs is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you do not select any parameter from the parameter list, the configuration is displayed for all interfaces. Result The information on the MLD snooping group is displayed. Further notes You enable MLD snooping with the command. ipv6 mld snooping SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note Vlan Keyword for a VLAN connection vlan-id Number of the addressed VLAN 1 ... 4094 If you specify VLAN, the configuration of all VLANs is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● You are in the Global configuration mode or in the VLAN configuration mode. The command prompt is in the Global configuration mode is: cli(config)# or in the VLAN configuration mode: cli(config-vlan-$$$)# Syntax Call the command without parameter assignment: ipv6 mld snooping SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable MLD snooping with the command. ipv6 mld snooping 8.7.2.3 ipv6 mld snooping clear counters Description With this command, you reset the counters of the MLD snooping statistics to zero. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
<(130 - 1225) seconds> The parameters have the following meaning: Parameter Description Range of values / note Value for the purge time in seconds 130 ... 1225 Default: 260 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure the setting with the command. ipv6 mld snooping port-purge-interval You can display the status of this function and other information with the show ipv6 mld command. snooping globals SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameter assignment: ipv6 mld snooping Result MLD snooping is enabled. Further notes You disable GMRP with the command. no grmp You disable MLD snooping with the command. no ipv6 mld snooping SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable MLD snooping with the command. ipv6 mld snooping 8.7.3.3 ipv6 mld snooping querier Description With this command, you configure the MLD snooping on the device as querier for a specific VLAN. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description This command specifies which version of MLD the device will use in this VLAN. Requirement You are in the VLAN configuration mode. The command prompt is as follows: cli(config-vlan-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 438
{v1 | v2} The parameters have the following meaning: Parameter Description MLDv1 MLDv2 Default Result The version of MLD used by the device in this VLAN is specified. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ip protocol SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: show ip ospf Result The configuration for routing with OSPF is displayed. 9.2.1.2 show ip ospf route Description This command shows the routes that were generated with OSPF. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows a summary of the database. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows information about a specific or all LSA types. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 443
LSAs of the local router are displayed. self-originate Number of LSAs generated by the local router For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the information on the OSPF interface. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows information about the detected neighboring routers. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the request list. This request list contains the information required for the LSAs. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows which queries are still open in the form of a list. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ip ospf virtual-links SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli (config-ospf)# Further notes You disable routing with OSPF with the command. no router ospf You enable IPv4 routing with the command. ip routing SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Router configuration mode with the command, you return to the Global exit configuration mode. ● If you exit the Router configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You disable the autonomous system boundary router with the command. no ASBR Router You can display the status of this function and other information with the show ip ospf command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you assign an area ID an address range. The address range is used to group the routes within OSPF. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 454
You delete the address range with the command. no area range You can display the status of this function and other information with the show ip ospf - command. area-range / summary-address SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
OSPF. Note This command is available only with layer 3. Requirement You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 456
You delete the address range with the command. no area range You can display the status of this function and other information with the show ip ospf - command. area-range / summary-address SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The address range is deleted. Further notes You create address ranges with the command. area range SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Generating a standard route (LSA type information- originate 7) in the NSSA. Result The area of the type NSSA is configured. Further notes You change the type of the area with the command. no area SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The router does not send or receive a summary LSA Result The area of the type Stub is configured. Further notes You change the type of the area with the command. no area SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
= 0 ... 255 The area ID 0.0.0.0 is reserved for the backbone area and cannot be deleted. stub Stub area nssa NSSA area Result The area is removed or changed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call up the command with the following parameters: area <area-id> virtual-link <router-id> [authentication simple |messagedigest| null [hello-interval <value (1-65535)>] [retransmit-interval <value(0-3600)>] [transmit-delay <value (0-3600)>] [dead-interval <value>] authentication-key <key (8)> | message-digest-key <Key-id (0-255)> md5 <key(16)> SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 462
Keyword for the ID of the password key-id ID of the password. specify the ID 0 ... 255 Keyword for the password Password enter the password Maximum length: characters SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete a virtual link. Note This command is available only with layer 3. Requirement You are in the OSPF Router configuration mode. The command prompt is as follows: cli(config-ospf)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 464
"failed" if Hello packets from it are not received. authentication-key Keyword for the unencrypted pass- word message-digest-key Keyword for the ID of the password key-id ID of the password. specify the ID 0 ... 255 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The compatibility with RFC 1583 is enabled. Further notes You disable the compatibility with the command. no compatible rfc1583 You can display the status of this function and other information with the show ip command. ospf SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the function with which a standard route is generated for external routes into the OSPF routing domain. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 467
1 - type 1 • External and internal costs 2 - type 2 • External costs Result The function is enabled. Further notes You disable the function with the command. no default-information originate SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Keyword for the type of the external standard route type Type of the external route 1 - type 1 • External and internal costs 2 - type 2 • External costs Result The function is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Keyword for the type of the external standard route type Type of the external route 1 - type 1 • External and internal costs 2 - type 2 • External costs Result The function is enabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Keyword for the type of the external standard route type Type of the external route 1 - type 1 • External and internal costs 2 - type 2 • External costs Result The function is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You remove the OSPF interface and the area with the command. no network area You can display the status of this function and other information with the show ip ospf command. interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You create the OSPF interface and the area with the command. network area You can display the status of this function and other information with the show ip ospf command. interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
• asExttype2 External costs For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The information for the route is specified. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The information for the route is deleted. Further notes You create the information with the command. redist-config SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You disable the distribution of the routes with the command. no redistribute You create the information for the routes with the command. redist-config You create the information for external the routes with the default-information originate command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable the distribution of the routes with the command. redistribute 9.2.3.23 distribute-list route-map Description This command enables the filtering of the routing information according to a route map for incoming routing information. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
<name(1-20)> in The parameters have the following meaning: Parameter Description Range of values / note name Name of the routing table. Maximum of 20 characters. Incoming routing information is filtered. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
(Page 39)". Result The ID of the router is specified. Further notes You display the router ID and other information with the command. show ip ospf interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● The router is an area border router (ABR) ● You are in the OSPF Router configuration mode. The command prompt is: cli(config-ospf)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 480
LSA message is translated disabled P bit = 0. LSA message is not translated For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
ID. x.x.x.x x = 255 0.0.0.0 = backbone area For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● Authentication using MD5: A password and a key ID are created. ● Authentication using an unencrypted password: A password is created. ● You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The interface is an IPv4 interface. ● You are in the Interface configuration mode. The command prompt is: cli(config-if-$$$)# Syntax Call the command without parameter assignment: ip ospf authentication SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note Password Password Enter a password. Maximum length: 8 characters Result The password is specified. Further notes You delete the password with the command. no ip ospf authentication-key SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure the password with the command. ip ospf authentication-key 9.2.4.5 ip ospf cost Description With this command, you specify the costs for the OSPF interface. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note This command is available only with layer 3. Requirement ● The interface is an IPv4 interface. ● You are in the Interface configuration mode. The command prompt is: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call up the command with the following parameters: ip ospf dead-interval <seconds (0-0x7fffffff)> The parameter has the following meaning: Parameter Description Range of values / note seconds 0 ... 0x7fffffff Interval in seconds SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You specify the interval with the command. ip ospf dead-interval You show the configuration of the OSPF interface with the show ip ospf interface command. You configure the router port with the command. no switchport SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The interval is specified. Further notes You delete the interval with the command. no ip ospf hello-interval You show the configuration of the OSPF interface with the show ip ospf interface command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
9.2.4.11 ip ospf message-digest-key Description With this command, you specify the password and the ID for authentication with MD5. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note This command is available only with layer 3. Requirement ● The interface is an IPv4 interface. ● You are in the Interface configuration mode. The command prompt is: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call up the command with the following parameters: ip ospf retransmit-interval <seconds (0 - 3600)> The parameter has the following meaning: Parameter Description Range of values / note seconds 0 - 3600 Interval in seconds SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The interval is deleted. Further notes You configure the interval with the command. ip ospf retransmit-interval You configure the router port with the command. no switchport SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You delete the interval with the command. no ip ospf transmit-delay 9.2.4.16 no ip ospf transmit-delay Description With this command, you delete the interval. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The interface is an IPv4 interface. ● You are in the Interface configuration mode. The command prompt is: cli(config-if)# Syntax Call up the command with the following parameters: ip ospf priority <value (0 - 255)> SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The value for the priority is reset to the default. Further notes You configure the priority with the command. ip ospf priority You display the router ID and other information with the command. show ip ospf interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
LSAs – Router LSA – Network LSA – Inter-area prefix LSA – Inter area router LSA – Intra area prefix LSA ● AS scope LSDB Contains the AS external LSA SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 500
Information in detail shows Information in hexadecimal format If you do not select any parameters from the parameter list, the entire content od the database is shown. Result The information is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The host table is shown. 9.3.1.6 show ipv6 ospf interface Description This command shows the information on the OSPFv3 interface. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ipv6 ospf redist-config Result The information is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The overview is displayed. 9.3.1.12 show ipv6 ospf area-range Description This command shows the grouped address ranges. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Privileged EXEC mode again. 9.3.2.1 ipv6 router ospf Description With this command, you enable routing with OSPFv3 and change to the Router configuration mode. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: no ipv6 router ospf SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure areas of the type NSSA (not-so-stubby-area) or stub. Note This command is available only with layer 3. Requirement You are in the OSPFv3 router configuration mode. The command prompt is as follows: cli(config-ospfv3)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you remove or change an area. To remove an area, there must be no IPv6 interface connected to it. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 512
128: The node (host) itself (from left to right) For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The area is removed or changed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Keyword for the costs value Costs for the OSPF interface. 1 ... 65535 For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● The area is of the type NSSA ● You are in the OSPFv3 router configuration mode. The command prompt is as follows: cli(config-ospfv3)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 515
You configure the area with the command. area You can display the status of this function and other information with the show ipv6 ospf - command. area-range / summary-address SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Keyword for the costs value Costs for the OSPF interface 1 ... 65535 For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● The area is of the type NSSA ● You are in the OSPFv3 router configuration mode. The command prompt is as follows: cli(config-ospfv3)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 518
P bit = 0. LSA message is not translated For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The address range is configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The virtual link needs to be configured on both routers ● Both routers are connected to the transit area. ● You are in the OSPFv3 router configuration mode. The command prompt is as follows: cli(config-ospfv3)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 520
Default: 60 The value must be a multiple of the hello interval. The routers located on the same link must have the same interval. Result The virtual link is created. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You create the information for the routes with the command. redist-config You can display the status of this function and other information with the show ipv6 ospf command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you create an entry in the host table and assign an area ID and / or a metric to it. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 523
The entry is configured in the host table. Further notes You remove an entry with the command. no host You display the host table with the command. show ipv6 ospf host SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
(Page 39)". Result The entry has been removed Further notes You create an entry with the command. host You display the host table with the command. show ipv6 ospf host SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
9.3.3.13 no passive-interface Description With this command, you specify that the OSPFv3 interfaces are active, that are configured afterwards. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● The router is an ASBR router. ● You are in the OSPFv3 router configuration mode. The command prompt is as follows: cli(config-ospfv3)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 527
You enable the distribution of the routes with the command. redistribute You delete the information with the command. no redist-config You display the setting with the command. show ipv6 ospf SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Further notes You enable the ASBR router with the command. ASBR Router You create the information with the command. redist-config You display the setting with the command. show ipv6 ospf SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You disable the distribution of the routes with the command. no redistribute You create the information for the routes with the command. redist-config You display the setting with the command. show ipv6 ospf SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable the ASBR router with the command. ASBR Router You enable the distribution of the routes with the command. redistribute You display the setting with the command. show ipv6 ospf SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
= 0 ... 255 Result The ID of the router is specified. Further notes You display the router ID and other information with the show ipv6 ospf interface command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The interface is an IPv6 interface. ● The router ID is configured. ● OSPFv3 routing is activated. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable OSPFv3 on the interface. Note This command is available only with layer 3. Requirement ● The interface is an IPv6 interface. ● The router ID is configured. ● OSPFv3 routing is activated. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The interface is an IPv6 interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# Syntax Call up the command with the following parameters: ipv6 ospf dead-interval <interval> SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The interface is an IPv6 interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# Syntax Call the command without parameter assignment: no ipv6 ospf dead-interval SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note interval Interval in seconds 1 ... 65535 Default: 10 The routers located on the same link must have the same interval. Result The interval is specified. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable OSPFv3 routing with the command. ipv6 router ospf You configure the interval with the command. ipv6 ospf hello-interval You display the configuration with the command. show ip ospf interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure the OSPF network with the command. ipv6 ospf network You enable OSPFv3 routing with the command. ipv6 router ospf You display information about the configuration with the show ipv6 ospf interface command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display information about the configuration with the show ipv6 ospf interface command. 9.3.4.9 ipv6 ospf metric Description With this command, you specify the metric for OSPF. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
9.3.4.10 no ipv6 ospf metric Description With this command, you reset the metric back to the default value. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The interface is an IPv6 interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# Syntax Call the command without parameter assignment: ipv6 ospf passive-interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable OSPFv3 routing with the command. ipv6 router ospf You deactivate the OSPFv3 interface with the command. ipv6 ospf passive-interface You display the configuration with the command. show ipv6 ospf interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable OSPFv3 routing with the command. ipv6 router ospf You reset the priority to the default with the command. no ipv6 ospf priority You display the configuration with the command. show ipv6 ospf interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command you specify the time after which packets whose receipt was not confirmed are transferred again. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
9.3.4.16 no ipv6 ospf retransmit-interval Description With this command, you reset the interval to the default value. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● The interface is an IPv6 interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 547
You enable OSPFv3 routing with the command. ipv6 router ospf You reset the interval to the default with the command. no ipv6 ospf transmit-interval You display the configuration with the command. show ipv6 ospf interface SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Router ports are not supported • Enable routing to be able to use VRRP. • VRRP supports only IPv4. If you want to use IPv4 and IPv6, use VRRPv3 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
VRRP. statistics shows the statistics of the VRRP pro- tocol For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
VRRP. statistics shows the statistics of the VRRP pro- tocol For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameter assignment: router vrrp Result Routing with VRRP is enabled. You are now in the VRRP Router Configuration mode. The command prompt is as follows: cli (config-vrrp)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the VRRP Router Configuration mode with the command, you return to exit the Global Configuration mode. ● If you exit the VRRP Router Configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You delete a VRRP interface with the command. no interface You display the status and the configuration of the VRRP interfaces with the show vrrp command. interface show vrrp interface - vrid SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure a VRRP interface with the command. interface You display the status and the configuration of the VRRP interface with the show vrrp command. interface show vrrp interface - vrid SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● The Router configuration mode is enabed. ● You are in the VRRP Router configuration mode. The command prompt is: cli(config-vrrp)# Syntax Call the command without parameters: no vrrp virtual-ping SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Privileged EXEC mode. 9.4.4.1 vrrp associated-ip Description With this command, you specify which IPv4 addresses the virtual router monitors. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you remove an IPv4 address from the virtual router. Note This command is available only with layer 3. Requirement You are in the VRRP Interface configuration mode. The command prompt is as follows: cli(config-vrrp-if)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you remove all assigned IPv4 addresses from the virtual router. Note This command is available only with layer 3. Requirement You are in the VRRP Interface configuration mode. The command prompt is as follows: cli(config-vrrp-if)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IPv4 address is assigned to the virtual router. ● You are in the VRRP Interface configuration mode .The command prompt is: cli(config-vrrp-if)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IPv4 address is assigned to the virtual router. ● You are in the VRRP Interface configuration mode .The command prompt is: cli(config-vrrp-if)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you specify the primary IPv4 address specified with the VRRP packets as the source address. Note This command is available only with layer 3. Requirement You are in the VRRP Interface configuration mode. The command prompt is as follows: cli(config-vrrp-if)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you remove an IPv4 address from the virtual router. Note This command is available only with layer 3. Requirement You are in the VRRP Interface configuration mode. The command prompt is as follows: cli (config-vrrp-if)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IPv4 address is assigned to the virtual router. ● You are in the VRRP Interface configuration mode .The command prompt is: cli(config-vrrp-if)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IPv4 address is assigned to the virtual router. ● You are in the VRRP Interface configuration mode .The command prompt is: cli(config-vrrp-if)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● An IPv4 address is assigned to the virtual router. ● You are in the VRRP Interface configuration mode .The command prompt is: cli(config-vrrp-if)# Syntax Call up the command with the following parameters: vrrp <vrid(1-255)> text-authentication <password> SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call up the command with the following parameters: no vrrp <vrid(1-255)> text-authentication The parameter has the following meaning: Parameter Description Range of values / note vrid ID of the virtual router 1 ... 255 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note vrid ID of the virtual router 1 ... 255 interval Time interval in seconds 1 ... 255 Default: 1 s Result The time interval is specified SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You configure the interval with the command. vrrp timer You assign IPv4 addresses to a virtual router with the command. vrrp ipv4 You show the interval with the command. show vrrp interface - vrid SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Further notes You display the table with the commands show vrrp3 interface show vrrp3 interface - vrid 9.5.2 The "show" commands This section describes commands with which you display various settings. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
VRRP pro- tocol For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The settings for the interface are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
VRRP pro- tocol For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The settings of the virtual router are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You disable routing with VRRP with the command. no router vrrp3 You enable IPv6 routing with the command. ipv6 unicast-routing You configure an IPv6 address for the interface with the command. ipv6 address SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the VRRP3 Router configuration mode with the command, you return to exit the Global configuration mode. ● If you exit the VRRP3 Router configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You delete a VRRP3 interface with the command. no interface You display the status and the configuration of the VRRP3 interfaces with the show vrrp3 command. interface show vrrp3 interface - vrid SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the status and the configuration of the VRRP3 interface with the show vrrp3 command. interface show vrrp3 interface - vrid 9.5.4.3 vrrp virtual-ping Description With this command, you enable the ping function to virtual IPv4 addresses. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the VRRP3 Router configuration mode. The command prompt is as follows: cli (config-vrrp-v3)# Syntax Call the command without parameter assignment: no vrrp virtual-ping Result The function for pings to virtual IPv4 addresses is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you specify which IP addresses the virtual router monitors. Note This command is available only with layer 3. Requirement You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you remove an IP address from the virtual router. Note This command is available only with layer 3. Requirement You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
VRRP packets of version 3. Note This command is available only with layer 3. Requirement You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you specify the primary IP address specified with the VRRP3 packets as the source address. Note This command is available only with layer 3. Requirement You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you remove a primary IP address from the virtual router. Note This command is available only with layer 3. Requirement You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only with layer 3. Requirement ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● Routing with VRRP3 is enabled. ● An IP address is assigned to the virtual router. ● You are in the VRRP3 Interface configuration mode. The command prompt is as follows: cli(config-vrrp-v3-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description This command shows the RIP information. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note_on_layer 3 Note These commands are available only with layer 3. 9.6.2.2 router rip Description With this command, you enable the RIP protocol and change to the Router configuration mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command is available only in layer 3 (IPv4). Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: no router rip SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
As default, this function is enabled. Requirement You are in the RIPv2 Router configuration mode. The command prompt is as follows: cli(config-rip)# Syntax Call the command without parameter assignment: auto-summary SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Routing information from a system with the value "255" is so unreliable that it is not learnt by the neighbor routers. Requirement You are in the RIPv2 Router configuration mode. The command prompt is as follows: cli(config-rip)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
[route-map <name(20)>] The parameters have the following meaning: Parameter Description Range of values / note route-map Keyword for a route map name Name of the route map Maximum of 20 characters. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The filtering is enabled. 9.6.3.7 no distribute-list route-map Description This command disables the filtering of the routing information according to a route map for incoming or outgoing routing information. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The IP address for which RIP will be Specify a valid IP address. enabled. For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
RIP is disabled for the specified IP interface. 9.6.3.10 redistribute Description This command specifies which route information is forwarded by RIP. Requirement You are in the RIPv2 Router configuration mode. The command prompt is as follows: cli(config-rip)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description This command specifies which route information is not forwarded by RIP. Requirement You are in the RIPv2 Router configuration mode. The command prompt is as follows: cli(config-rip)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the RIPv2 Router configuration mode. The command prompt is as follows: cli(config-rip)# Syntax Call up the command with the following parameters: version <1 | 2| 12 | none> SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the RIPv2 Router configuration mode. The command prompt is as follows: cli(config-rip)# Syntax Call the command without parameter assignment: no version Result Both RIPv1 and RIPv2 packets are processed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Value for the metric information. 1 ... 15 Result The default route is forwarded. 9.6.4.3 no ip rip default route originate Description This command disables the distribution of the default routes. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note Only RIPv1 updates are received. Only updates to RIPv2 are received. Updates that correspond to RIPv1 or RIPv2 are received. none No RIP updates are received. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command specifies the RIP version for outgoing routing information. Requirement ● The interface is an IPv4 interface. ● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: no ip rip send version Result All RIP updates are sent. RIPng (IPv6) This section describes the commands relevant for working with routing with RIPng. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The information of the RIP database is displayed. Result The information of the RIP database is displayed. Further notes You enable routing with RIP with the command. ipv6 router rip SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ipv6 rip peer-table-status Result The information is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameter assignment: show ipv6 rip stats Result The information is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli (config-ripng)# Further notes You disable routing with RIPng with the command. no ipv6 router rip You display the setting and other information with the command. show ipv6 rip SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Router Configuration mode with the command, you return to the exit Global Configuration mode. ● If you exit the Router Configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
1 ... 255 tance. Default: 120 route-map Keyword for a route map name Name of the route map Maximum of 20 characters. Result The value for the administrative distance is set. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description This command enables the filtering of the routing information according to an IPv6 address for incoming or outgoing routing information. Note This command is available only with layer 3. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note This command is available only with layer 3. Requirement You are in the RIPng router configuration mode. The command prompt is as follows: cli(config-ripng)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command enables the filtering of the routing information according to a route map for incoming or outgoing routing information. Requirement You are in the RIPng router configuration mode. The command prompt is as follows: cli(config-ripng)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Name of the routing table. Maximum of 20 characters. The filtering for incoming routing infor- mation is disabled. The filtering for outgoing routing infor- mation is disabled. Result The filtering is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The information forwarded by RIP has been specified. Further notes You disable the forwarding with the command. no redistribute You display the setting and other information with the command. show ipv6 rip SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
In certain cases, forwarding of routing information is disabled. Further notes You enable the forwarding with the command. no redistribute metric You display the setting and other information with the command. show ipv6 rip SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameter assignment: ipv6 rip default-information originate Result The function is enabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You enable IPv6 with the command. ipv6 enable You enable the function with the command. ipv6 rip default-information originate 9.7.4.3 ipv6 rip Description This command enables RIPng routing on the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● You are in the Interface configuration mode The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameter assignment: no ipv6 rip Result RIPng routing is enabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
<integer (1-15)> The parameter has the following meaning: Parameter Description Range of values / note integer Metric offset 1 ... 15 Default: 1 Result The metric offset is configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note name Name of the route map 1 ... 20 If no parameters are specified, all configured route maps are displayed. Result The route maps are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command you create a route map and change to the Route maps configuration mode. Note This command is available only with layer 3. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete a route map. Note This command is available only with layer 3. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you specify whether or not the routing information for a route map is filtered based on the destination IPv4 address. Note This command is available only with layer 3 (IPv4). SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for the destination IPv4 address. Note This command is available only with layer 3 (IPv4). Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
IPv6 address. Note This command is available only with layer 3 (IPv6). Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for the destination IPv6 address. Note This command is available only with layer 3 (IPv6). Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for the interface. Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for the value of the metric. Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for the type of the metric. Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
(IPv4) to which the routing information is sent next. Note This command is available only with layer 3 (IPv4). Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for the next router (IPv4). Note This command is available only with layer 3 (IPv4). Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
(IPv6) to which the routing information is sent next. Note This command is available only with layer 3 (IPv6). Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for the next router (IPv6). Note This command is available only with layer 3 (IPv6). Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for the type of the route. Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the filter for a tag. Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you specify whether the routing information is forwarded with a changed metric. Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete the setting that the metric of the routing information is changed. Note This command is available only with layer 3. Requirement You are now in the Route maps configuration mode. The command prompt is as follows: cli(config-rmap-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Value of the tag 1 ... 0xffffff Enter the new value for the tag with which the routing infor- mation will be forwarded. You can enter the value in decimal or hexadecimal. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You define the setting that the tag of the routing information is changed with the set tag command. You change to the Route maps configuration mode with the command route-map You display the setting and other information with the command. show route-map SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the packet rate for limiting the outgoing data stream of one or all interfaces. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure and enable the data rate in Kbps for limiting the outgoing data stream of the interface. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no rate-limit output Result The limitation of the outgoing data stream of the interface with the data rate is disabled. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The default value for the storm control level is 0 Kbps. The incoming data stream is not limited. To have the incoming data stream limited, configure the threshold value with the storm- command. control level SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The storm control function is disabled. Further notes You enable the function with the command. storm-control SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you reset the value for the storm control function to the default value. The default value for the storm control level is 0 Kbps. The incoming data stream is not limited. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Privileged EXEC mode again. 10.2.1.1 mac-address-table block static multicast Description With this command, you configure a static multicast MAC address without outgoing ports. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you generate a static multicast MAC address entry in the forwarding database. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
10.2.1.3 no mac-address-table static multicast Description With this command, you delete a static multicast MAC address entry from the forwarding database. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you generate a static unicast MAC address entry in the forwarding database. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete a static unicast MAC address entry from the forwarding database. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With incoming packets, the ingress filter checks whether the port on which the packet was received belongs to the sending VLAN. If this is not the case, the packet is not processed. With this command, you enable the ingress filter. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: no switchport ingress-filter Result The ingress filter is deactivated. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show mac-address-table aging-time Result The time is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure the aging of a dynamically learned entry in the MAC address list. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The command prompt is as follows: cli(config)# Syntax Call the command without parameters: no mac-address-table aging-time Result The value of the aging of a dynamically learned entry is reset to the default value. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
10.3.2.4 no mac-address-table aging Description With this command, you disable the "Aging" function. Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the settings of the flow control function. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure the flow control function for an interface. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show qos cos-map SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show qos-trust-mode SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: Result You are now in the QOS configuration mode. The command prompt is as follows: cli(config-qos)# Further notes You exit the QOS configuration modewith the command exit SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With queues 7 - 8 only frames with a high priority are processed as long as there are frames with high priority in the queue. Requirement You are in the QOS configuration mode. The command prompt is as follows: cli(config-qos)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With queues 7 - 8 only frames with a high priority are processed as long as there are frames with high priority in the queue. Requirement You are in the QOS configuration mode. The command prompt is as follows: cli(config-qos)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command you can set the method according to which packets to be forwarded are prioritized port by port. Requirement You are in the QOS configuration mode. The command prompt is as follows: cli(config-qos)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 674
VLAN tag it is forwarded with the prioritization of the receiving port. For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The prioritization for forwarding packets is configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: show roles Result The created roles are shown. Further notes You create a role with the command. role You delete a role with the command. no role SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You delete a link in the table "External User Accounts" with the no user-account-ext command. 11.1.1.3 show user-groups Description This command shows the links between groups and roles. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show users Result The logged-in CLI users are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Even if you change the password in Trial mode, this change is saved immediately. Further notes You create a user with the command. user-account You delete a user with the command. no user-account You show the created users with the command. show user-accounts SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you create roles that are valid locally on the device. Note You can create up to 28 additional roles. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 680
You can only change the function rights of a role when the role is no longer linked to a user. Further notes You delete a role with the command. no role You show the created roles with the command. show roles SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
When you create a local user an entry is generated automatically in the table "External User Accounts". Note You can create up to 16 additional user accounts. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 682
After creating a user, the user name can no longer be modified. If a user name needs to be changed, the user must be deleted and a new user created. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Enter a valid user name. Result The user has been deleted. Further notes You create a user with the command. user-account You show the created users with the command. show user-accounts SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Keyword for the description user-ext- Content of the description Enter a description for the user in the description table "External User Accounts". The de- scription text can be up to 100 characters long. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameter has the following meaning: Parameter Description Range of values / note user-name-ext User name Enter the name of a user. Result The link in the table "External User Accounts" has been deleted. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command you link a group with a role. Note You can create up to 32 groups. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You show the created links with the command. show user-groups 11.1.4.8 no user-group Description With this command, you delete the link between a group and a role. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you change the password of the factory set default users " " and user " ". admin Requirement You are in the Global Configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This makes central administration of user data possible. This section describes commands relevant for the configuration of this service. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The connection statistics are displayed. 11.2.1.2 show radius server Description This command shows the RADIUS server configuration. Requirement You are in the Privileged EXEC mode. The command prompt is as follows: cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call up the command with the following parameters: login authentication {radius | local-and-radius | radius-fallback-local} SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you disable authentication via a RADIUS server. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameter assignment: no login authentication SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
"External User Accounts". Result The assignment of rights during the login authentication is defined. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure a RADIUS server entry on the RADIUS client. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 695
The server is used only for the 802.1X authentication. login-dot1x The server is used for both authentica- Default setting tion procedures. For information on addresses and interfaces, refer to the section "Addresses and interface names (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Enter a valid IPv6 address. primary Identifies the RADIUS server as prima- ry server For information on addresses and interfaces, refer to the section "Addresses and interface names (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the configuration of the access control lists (Access Control List). Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". If you do not select any parameter from the parameter list, the configuration is displayed for all available interfaces. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Number of the access control list 1 ... 128 Result A MAC access control list has been generated. You are now in the MAC ACL configuration mode. The command prompt is as follows: cli(config-ext-macl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The MAC access control list is deleted. Further notes You generate a MAC ACL with the command. mac access-list extended You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Number of the access control list 1 ... 128 Specifies that incoming packets are filtered Specifies that outgoing packets are filtered Result The packets are filtered according to the access control list (ACL). SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The packet filtering according to the access control list (ACL) is canceled. Further notes You enable the setting with the command. mac access-group You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
{any|host<src-mac-address>}{any|host<dest-mac-address>} The parameters have the following meaning: Parameter Description Range of values / note Keyword for "all" host Keyword for the MAC address of an incoming connection that is permitted SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The access control lists are processed on the interface in the order in which they were created. The index number of the access control list is not used for this. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 705
You delete the MAC access control list with the command. no mac access-list extended You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Number of the access control list 1 … 128 If you do not select any parameters from the parameter list, the configuration of all access control lists will be displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Commands relating to other topics that can be called in the Global configuration mode can be found in the relevant sections. You exit the Global configuration mode with the command and are then in the exit Privileged EXEC mode again. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the configuration of the access control list with the command. show access-lists 11.4.2.2 no ip access-list Description With this command, you delete an IP access control list. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The packets are filtered according to the access control list (ACL). Further notes You disable the setting with the command. no ip access-group You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The packet filtering according to the access control list (ACL) is canceled. Further notes You enable the setting with the command. ip access-group You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameters have the following meaning: Parameter Description Range of values / note access-list-number Number of the access control list 1 ... 128 Specifies that incoming packets are filtered Specifies that outgoing packets are filtered SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The packet filtering according to the access control list (ACL) is canceled. Further notes You enable the setting with the command. ip access-group You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 715
If you create the rule for a single system (one IP address), you will need to specify the subnet mask "255,255,255,255". As an alternative, you can specify the keyword "host" followed by the IP address. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 717
Keyword for the Differentiated Services Codepoint value Value for the Differentiated Services 0 ... 63 Codepoint For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 719
Further notes You delete an IP access control list with the no ip access-list standard <acl-num> command. You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 721
Further notes You delete an IP access control list with the no ip access-list standard <acl-num> command. You display the configuration of the access control list with the command. show access-lists SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 723
Forwards RST segments. For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The IP access list for TCP segments has been configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 725
Blocks RST segments For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The IP access list for TCP segments has been configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 727
Codepoint For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The IP access list for UDP datagrams has been configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The index number of the access control list is not used for this. Requirement You are in the ACL standard configuration mode. The command prompt is as follows: cli(config-std-nacl)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 729
Codepoint For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The IP access list for UDP datagrams has been configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows whether or not the learning of MAC entries is enabled or locked on an interface. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete all static unicast MAC address entries from the MAC address table. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: auto-learn Result You are now in the AUTOLEARN mode. The command prompt is as follows: cli(config-auto-learn)# Further notes You exit the AUTOLEARN configuration modewith the command exit SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The learning of MAC addresses is blocked. Further notes You enable the learning of MAC addresses with the command. no switchport lock You display the configuration with the command. show lock port SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Privileged EXEC mode. 11.5.4.1 start Description With this command, you start automatic learning. During automatic learning, the aging timer is disabled for all learned addresses. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: stop Result Automatic learning is stopped and all learned entries are converted to static entries. Further notes You start automatic learning with the command. start SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on identifiers of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The information about the configuration of the authorized managers is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Result The authorized manager is activated. Further notes You disable the function with the command. no authorized-manager 11.6.2.2 no authorized-manager Description With this command, you disable the authorized manager. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure the interfaces and protocols via which an authorized manager is allowed to access the device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 739
• http • https • For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". The IP address 0.0.0.0 means "any manager". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you delete an interface via which an authorized manager is allowed to access the device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This section describes commands for working with port-based network access control (PNAC). 11.7.1 The "show" commands This section describes commands with which you display various settings. 11.7.1.1 show dot1x Description This command shows information about port-based network access control (PNAC). SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show dot1x guest-vlan mac-info SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you enable the guest VLAN function for the device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The guest VLAN function is disabled for the device. Further notes You enable the function with the command dot1x guest-vlan. You display this setting and other information with the show dot1x guest-vlan mac-info command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
11.7.2.4 no dot1x mac-auth Description With this command, you disable MAC authentication for the device. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the guest VLAN function for a port. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# Syntax Call the command without parameters: dot1x guest-vlan SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you configure a guest VLAN for a port. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command removes MAC addresses from the guest VLAN. If you specify a MAC address, only this MAC address is removed from the guest VLAN. If you use this command without parameters, all MAC addresses are removed from the guest VLAN. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call up the command with the following parameters: set dot1x guest-vlan mac-addr count <num-of-addresses (1-100)> The parameter has the following meaning: Parameter Description Range of values / note num-of-addresses Maximum number of devices 1 ... 100 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
11.7.3.8 no dot1x mac-auth Description With this command, you disable MAC authentication for a port. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
MAC authentication is reset for the port. 11.7.3.10 dot1x mac-auth vlan-assign Description With this command you enable the assignment of the VLAN ID for a MAC address by the RADIUS server. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The VLAN ID for a MAC address is no longer assigned by the RADIUS server. 11.7.3.12 dot1x port-control Description With this command, you configure port control parameter of the authenicator. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you reset the port control parameter of the authenicator to the default value. The default value is force-authorized With this, data traffic is permitted without restrictions. Requirement You are in the Interface Configuration mode. The command prompt is as follows: SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameter has the following meaning: Parameter Description Range of values / note num-of-addresses Maximum number of devices 1 ... 100 Result The maximum number of devices for the port has been specified. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you disable the function that repeats the authentication of the client by the authenticator periodically. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 756
Periodic authentication is disabled. Further notes You enable the function with the command. dot1x reauthentication You can display the status of this function and other information with the show command. dot1x SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
In events and faults handling, you set the events whose messages will be distributed in one of the available ways. You configure the monitoring of certain system events and power supply and physical interfaces in the Events configuration mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: no logging console SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command shows the degree of severity of an event ("Info", "Warning" or "Critical") starting at which a notification (sending of an e-mail, entry in the Syslog table, entry in the Syslog file) is generated. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Monitoring of the power supply for power outage link Monitoring of the network connections for a change in the connection status If no parameters are specified, the settings for both error monitoring functions are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show startup-information SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
All log entries of the category "Critical" are displayed. Result The content of the logbook is displayed. 12.1.3.7 show cabletest interface Description This command shows the result of the cable test of the interface. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
This command runs error diagnostics for an SFP port. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Call the command without parameters: show power-line-state Result The status of the power supply is displayed. 12.1.4 clear logbook Description With this command, you delete the content of the logbook. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you change to the EVENTS configuration mode. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# Syntax Call the command without parameters: events SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Pair 3 = pin 4-5 Pair 4 = pin 7-8 Requirement ● The interface has no active data traffic. ● You are in the Global configuration mode. The command prompt is: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Privileged EXEC mode. 12.1.6.1 add log Description With this command, you create an entry in the log. Requirement You are in the EVENTS Configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Enables the client that sends the messages to the Syslog server trap Enables the client that sends the SNMP traps email Enables the client that sends the e-mails Enables all clients at once SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The client selected for the transfer is disabled. Further notes You display the status of the events and the clients with the command. show events config You enable the function with the command. client config SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● Sending the message to the Syslog server ● Sending an e-mail ● Sending an SNMP trap Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 771
Error LED lights up. The setting is possible only for a cold or warm restart. All clients at once Result The setting deciding which message of the device is stored or forwarded is configured. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure which of the various message types of the device will no longer be stored or forwarded. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 773
You display the status of the events and the clients with the command. show events config You configure which of the various message types of the device will be stored or forwarded with the command. event config SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The settings for sending system event messages are configured. The "severity" function is enabled. Further notes You disable the setting with the command. no severity You display the status of this function and other information show events severity SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the status of this function and other information show events severity 12.1.6.8 power Description With this command, you configure and activate the monitoring of the power supplies. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
12.1.6.9 no power Description With this command, you disable the monitoring of the power supplies. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure and enable the monitoring of the physical network connections for cable breaks or for pulling of the connector. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you disable the monitoring of the physical network connections for cable breaks or for pulling of the connector. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If the value of the received power or the power loss falls below or exceeds the set limit values, an event is triggered. You can set limit values in two stages for messages with the severity levels "Warning" and "Critical". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The limits set for the received power and the power loss are displayed. 12.2.1.2 show fmp status Description This command shows the current status and the current values of the optical ports or connections that you monitor with fiber monitoring. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. 12.2.2.1 Description With this command, you enable fiber monitoring. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you disable fiber monitoring. Requirement You are in the Interface configuration mode. The command prompt is: cli(config-if-$$$)# Syntax Call the command without parameter assignment: no fmp Default: enabled SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the status of this function and other information with the show fmp stauts commands. show fmp limit You define the limit values for the received power with the command fmp rx-power SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the status of this function and other information with the show fmp stauts commands. show fmp limit You define the limit values for the power loss with the command fmp power-loss SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you display the information on loop detection. Detected loops are shown. Requirement You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". If you do not select any parameters from the parameter list, the default value is used. Result The loop interface is displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The loop detection function is enabled Further notes You disable the function with the command. no loopd You can display the status of this function and other information with the show loopd command. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you enable the loop detection function for VLAN. Requirement ● Loopd is activated ● You are in the Global configuration mode. The command prompt is: cli(config)# Syntax Call the command without parameters: loopd vlan mode SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The loop detection function is disabled for VLAN. Further notes You enable the function with the command. loopd vlan mode You can display the status of this function and other information with the show loopd command SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Loop detection frames are sent out and forwarded. If you do not select any parameters from the parameter list, the default value is used. Result It has been configured how the port handles loop detection frames. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
12.3.3.3 loopd reaction local Description With this command, you activate the "disable" reaction for a local loop. If a local loop is detected, the port is blocked. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Syntax Call the command without parameters: no loopd reaction local Result "no action" is activated for the function. loopd reaction local "disable" is the default after enabling loop detection. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you enable the "no action" reaction for a remote loop. If a remote loop is detected, this has no effect on the port. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Mirroring a port does not work beyond switch core boundaries. Note You need to disable port mirroring if you want to connect a normal end device to the monitor port. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description This command shows the status of the communication via the monitor port. If you enable this option, management of the switch via the monitor port is no longer reachable. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Range of values / note session Keyword for a session whose settings are displayed session-id Number of the session 1 ... 7 Result The settings for mirroring ports are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the status of this function with the command. show monitor You disable the function with the command. no monitor 12.4.2.2 no monitor Description With this command, you disable the port mirroring function. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If mirroring is disabled, the listed port-specific functions are reset to the default values. This reset takes place regardless of whether the functions were configured manually or automatically by enabling monitor barrier. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Communication via the monitor port is enabled. Further notes You disable the communication with the command. monitor barrier enabled You display the configuration settings with the command. show monitor barrier SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
If you connect a BUS ANALYZER Agent XM-400 with a Module no. and port no. of the interface SCALANCE XM-400 basic device as of firmware version 5.1, you can select up to four ports of the BUS ANALYZER Agent XM-400 as destination ports. The BUS ANALYZER Agent XM-400 supports port-based and VLAN-based mirror- ing.
Description With this command, you delete the destination for mirroring a port. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the configuration settings with the command. show monitor session 12.4.2.7 monitor session source Description With this command, you configure the source for mirroring a port or a VLAN. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 803
Keyword for an IP access control list acl-id Number of the Access Control List For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you delete the source for mirroring a port or a VLAN. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 805
The source for the mirroring of a port is deleted. Further notes You configure the source for mirroring a port with the command. monitor session ... source You end and delete a session with the command. no monitor session SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● Entry in the local log ● Sending as SNMP trap ● Transfer to the Syslog server ● Transfer to a network management station using SNMP SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you can display several parameters with one call. If you do not select any parameters from the parameter list, only the enabled disabled status is shown. Result The settings of the remote monitoring function are displayed. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You can display the status of this function and other information with the show rmon command. 12.5.2.2 no rmon Description With this command, you disable the Remote Monitoring function. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Events are assigned to these occurrences. Requirement You are in the Global configuration mode. The command prompt is as follows: cli(config)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 810
With the RMON function, only MIB variables of the Ethernet interfaces can be monitored. Note Magnitude of the threshold values The threshold value for falling or low variable values should be less than the threshold value for rising or high variable values. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
The parameter has the following meaning: Parameter Description Range of values / note number Number of the alarm to be deleted 1 ... 52 Result The entry for monitoring a MIB variable is deleted. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You display the RMON Event Table with the command. show rmon events You show the details of the SNMP community with the command. show snmp community SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
● If you exit the Interface configuration mode with the command, you return to the exit Global configuration mode. ● If you exit the Interface configuration mode with the command, you return to the Privileged EXEC mode. SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you end the recording of statistical data of an interface. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
With this command, you configure the collection of statistical data of the interface in a selectable number of recording intervals ("Buckets ") with a specified period. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Description With this command, you end the recording of statistical data of the interface. Requirement You are in the Interface configuration mode. The command prompt is as follows: cli(config-if-$$$)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
You are in the User EXEC mode or in the Privileged EXEC mode. The command prompt is as follows: cli> cli# Syntax Call the command without parameters: show events syslogserver SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Privileged EXEC mode. 12.6.2.1 syslogserver Description With this command, you configure the Syslog server. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
12.6.2.2 no syslogserver Description With this command, you delete a Syslog server. Requirement You are in the EVENTS configuration mode. The command prompt is as follows: cli(config-events)# SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 820
For information on names of addresses and interfaces, refer to the section "Interface identifiers and addresses (Page 39)". Result The Syslog server is deleted. Further notes You add a Syslog server with the command. syslogserver SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
4861 Neighbor Discovery for IP version 6 (IPv6) 4862 IPv6 Stateless Address Autoconfiguration 5095 Deprecation of Type 0 Routing Headers in IPv6 6603 Prefix exclude option for DHCPv6-based prefix delegation SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 822
Appendix A A.1 Supported RFCs SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 826
633 no match tag, 644 match metric-type, 635 no monitor session destination, 801 match next-hop ip, 637 no multicast-block, 95 match next-hop ip (IPv4), 637 no nfc active, 131 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 827
163 no router rip, 593 ptp time diff, 164 router vrrp, 551 ptp transparent-clock configuration, 164 no router vrrp, 552 router vrrp3, 572 no router vrrp3, 573 qos, 670 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 828
698, 707 show ipv6 ospf interface, 502 show interface mtu, 60 show ipv6 ospf neighbor, 503 show interfaces, 60 show ipv6 ospf redist-config, 504 show interfaces ... counters, 61 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 829
406 signaling-contact status, 142 show rmon, 807 SIMATIC NET glossary, 29 show route-map, 624 smtp-port, 373 show running-config, 114 no smtp-port, 374 show signaling contact, 141 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 830
244 no switchport pvid, 197 spanning-tree mst (properties), 236 syslogserver, 818 no spanning-tree mst, 238 no syslogserver, 819 spanning-tree mst configuration, 226 system contact, 83 system location, 83 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 831
582 vrrp group shutdown (VRRP), 558 vrrp ipv4 (VRRP) no vrrp ipv4, 562 vrrp ipv4 (VRRP3) no vrrp ipv4, 586 vrrp preempt (VRRP), 559 no vrrp preempt, 560 SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...
Page 832
Index SCALANCE XM-400/XR-500 Command Line Interface (CLI) Configuration Manual, 11/2015, C79000-G8976-C252-10...