Philips VARI-LITE VL6000 Beam Luminaire User Manual page 58

❋
VARI LITE - VL6000 B
Table 2: VL6000 Beam Luminaire 16-Bit DMX Channel Mapping
DMX
Parameters
Channel
Gobo 1 Rot/Index
16
High Byte
17
Low Byte
Gobo Wheel 1
18
Control
19 Iris
20 Frost
21 Strobe Speed
22 Strobe Control
Luminaire
23
Control
Notes:
Default Values: *Denotes recommended console default settings.
40
L U '
EAM UMINAIRE SER
Range Range
(DMX) (%)
0 - 65535 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
0 - 255 0 - 100%
2 7 Ap ri l 2 017
M
S ANUAL
Default
Description / Operation
Value*
16-bit control of index and rotation of gobo wheel 1.
0 0-32756 = Rotate Fast to Slow
32757-32780 = Rotation STOP
32781-65535 = Rotate Slow to Fast
Used as a control channel for different movement options for Gobo
Wheel 1 (Channel 15)
0-5 = Gobo Selection using shortest (quickest) path.
6-10 = Gobo Selection using normal (longest) path.
11-20 = Reserved Values
21-50 = Wheel Spin Forward (Fast to Slow)
0
51-60 = Wheel Spin STOP
61-90 = Wheel Spin Reverse (Slow to Fast)
91-120 = Gobo Shake Quickest Path (Slow to Fast)
121-150 = Gobo Shake Normal Path (Slow to Fast)
151-180 = Gobo Twist Quickest Path (Slow to Fast)
181-210 = Gobo Twist Normal Path (Slow to Fast)
211-255 = Reserved Values
0 Controls Iris mechanism from open (DMX 0) to Full (DMX 255)
0 Controls Frost mechanism from open (DMX 0) to Full (DMX 255)
0 Controls Strobe rate from slowest (DMX 0) to fastest (DMX 255)
Control Channel for strobing functions
0-5 = Open
6-10 = Closed
0 11-15 = Normal Strobe
16-20 = Random Strobe
21-25 = Random Sync
26-255 = Reserved Values
Control Channel used for full fixture settings, lamp controls, and miscel-
laneous modes. Set descreet value of desired effect, wait >3 seconds,
then set value to 0 (Idle).
0-5 = Idle (Default)
6-10 = Full Luminaire ReCal-Also Used to Wake fixture up from shut-
down
11-15 = Lamp ON
16-20 = Lamp OFF
21-25 = Fixture Shutdown
26-30 = Display-Menu ON
31-35 = Display-Menu OFF
36-40 = ReCal Position
41-45 = ReCal Color
0 46-50 = ReCal Gobo
51-55 = ReCal Beam
56-60 = ReCal Dimmer/Strobe
61-65 = Reset Fixture to Defaults
66-70 = Full Luminaire Reboot. This command will douse lamp and
reset all processors in fixture, then ReCal all parameters.
71-75 = Fixture Status On/Off. This command will enable the display to
show fixture status for 5 min. After this time, displays will return to
default configuration. Repeating the command in less than 5 minutes
will behave as a toggle.
76-80 = Dimmer Snap Off (default)
81-85 = Dimmer Snap On
86-90 = Pan / Tilt Normal (Default)
91-95 = Pan / Tilt Fast
95-255 = Reserved Values
02.9708.0002