Edit Selective Call Ids; Factory Reset Feature - Motorola GP68 Service Manual

Radio Programming Information
Special Programming Mode (SPM)
pause between the digits of the ID by first pressing
immediately followed by
at the end of the ID are not stored.
Two medium-pitched "beeps" sound when a
pause is successfully entered, and the display
changes from 'A' to '–' to visually represent the
pause
Use or to scroll through the existing ID's
3
digits. To change the PTT ID, use
unwanted digits, and then enter the new digits. The dis-
play shows the new digits as they are being entered.
When the flashing cursor is under a digit, the maximum
number has been entered.
If you attempt to add more than 8 digits, an invalid
keypress tone sounds and the keypress is
ignored.
4a
Press the Enter Button to store the new PTT ID and
return to the SPM browse menu.
A valid keypress tone sounds when the ID has
been successfully stored.
4b To abort the data entry, select another menu item by
turning the Channel Selector Knob, or wait until the
edit mode times-out (after 5 seconds of inactivity).

Edit Selective Call IDs

NOTE
To support Selective Call o operation, the
Option Board Setting must be set to
'dECOdE' for Simple Decoder in order to
access the ID parameters.
Rotate the Channel Selector Knob to select the appro-
1
priate menu item (
= Individual Call ID,
= All Call ID).
Press any key (except the Enter Button) to enter the
2
appropriate edit mode. The LCD Screen displays the
currently programmed ID number. For an ID which
exceeds the length of the 6-digit display, the rightmost
digit flashes to indicate more digits exist on the right.
You can now enter or change digits as required, up to a max-
imum of 8, using any of the numeric keys, as well as the ∗,
#, A, B, C, and D keys. The flashing cursor indicates the
position of the next digit to be entered.
NOTE
Pause digits cannot be entered with Selective
Call ID numbers. Therefore, a '*' must not be
immediately followed by a '#', but they are
valid in combination with all other digits.
Use or to scroll through the existing ID's
3
4-12
. However, any pauses entered
to erase the
= Acknowledgment ID,
= Group Call ID and
, digits. To change the selected ID, use
unwanted digits, and then enter the new digits. The dis-
play shows the new digits as they are being entered.
When the flashing cursor is under a digit, the maximum
number of digits has been entered.
If you attempt to add more than 8 digits, an invalid
keypress tone sounds and the keypress is
ignored.
4a Press the Enter Button to store the ID number and
return to the SPM browse menu.
A valid keypress tone sounds when the ID has
been successfully stored.
4b To abort the data entry, select another menu item by
turning the Channel Selector Knob, or wait until the
edit mode times-out (after 5 seconds of inactivity).

Factory Reset Feature

This feature is intended to allow you to erase certain pro-
grammable parameters and restore the radio to the factory
default settings. The radio, upon reset, clears all memory
channels stored in the non-volatile memory area, clears all
phone number storage locations, and restores the default set-
tings to the different user-modifiable parameters (coded
squelch type, squelch level, channel-step size, etc.).
The Factory Reset feature does not clear the
IDs or access/de-access codes, nor does it
change the Option Board Setup setting.
1 With the radio in Special Programming Mode, press
and hold the PTT Button.
2 While holding PTT, press
sequence.
As the sequence is entered, the LCD Screen (which is ini-
tially cleared) displays an'o' for each digit entered.
Any incorrect digit entered results in an invalid
keypress tone, the LCD Screen is cleared again
and you must reenter the sequence, starting with
the first digit.
Once the sequence has been entered successfully, the LCD
Screen displays the prompt
procedure is ready to be activated.
Press the Enter Button to confirm the reset process.
3
Pressing any other key or releasing the PTT Button
cancels the process and returns the radio to the SPM
Browse menu.
The display blanks when the reset is in progress.
When the process is successfully completed, the
LCD Screen displays
tone sequence sounds.
6881086C09-O
GP68 Portable Radios Service Manual
to erase the
NOTE
, , , ,
1 3 5 7
, indicating that the reset
and a ringing reset
March, 1997
in
9