Intelligent Terminal Functions - Hitachi SJ700 series Manual

Code Function Name
b108 Free-setting V/f frequency (5)
b109 Free-setting V/f voltage (5)
b110 Free-setting V/f frequency (6)
b111 Free-setting V/f voltage (6)
b112 Free-setting V/f frequency (7)
b113 Free-setting V/f voltage (7)
b120 Brake control enable (*3)
b121 Brake wait time for release (*3)
b122 Brake wait time for acceleration (*3)
b123
Brake wait time for stopping (*3)
b124
Brake wait time for conÞ rmation (*3)
b125
Brake release frequency setting (*3)
b126
Brake release current setting (*3)
b127 Braking frequency (*3)
b130 Overvoltage suppression enable
b131 Overvoltage suppression level
Acceleration and deceleration rate
b132
at overvoltage suppression
b133 Overvoltage suppression propotional gain
b134 Overvoltage suppression Integral time
b141 Output loss detection enable (SJ700D only)
b142 Output loss detection sensibility (SJ700D only)
b164 Automatic return to initial display (SJ700D only)
b166 Data Read/Write select (SJ700D only)
b180 Initialization trigger (SJ700D only)
(*1) 4000HF: 0.00 to 120.0 (Hz)
● C GROUP: INTELLIGENT TERMINAL FUNCTIONS
Code Function Name
C001 Terminal [1] function (*1)
C002 Terminal [2] function
C003
Terminal [3] function (*1)
C004
Terminal [4] function
C005 Terminal [5] function
C006 Terminal [6] function
C007 Terminal [7] function
C008 Terminal [8] function
C011 Terminal (1) active state
C012 Terminal (2) active state
C013 Terminal (3) active state
C014 Terminal (4) active state
C015 Terminal (5) active state
C016 Terminal (6) active state
C017 Terminal (7) active state
C018 Terminal (8) active state
C019 Terminal FW active state
(*1) When the emergency stop function is enabled (SW1 = ON), "18" (RS) and "64" (EMR) are forcibly written to parameters "C001" and "C003",
respectively. (You cannot arbitrarily write "64" to "C001".) If the SW1 signal is turned o and then turned on, "no" (no assignment) is set in parameter "C003".
(*2) 1850HF,2200HF,3150HF and 4000HF:The function is not provided.
19
0. to "free-setting V/f frequency (6)" (Hz)
0.0 to 800.0 (V)
0. to "free-setting V/f frequency (7)" (Hz)
0.0 to 800.0 (V)
0.0 to 400.0 (Hz) (*4)
0.0 to 800.0 (V)
00 (disabling), 01 (enabling)
0.00 to 5.00 (s)
0.00 to 5.00 (s)
0.00 to 5.00 (s)
0.00 to 5.00 (s)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*1)
SJ700/SJ700D: 0.0 to 2.00 x "rated current" (A)
< 75kW and over:0.0 to 1.80 x "rated current" (A)>
SJ700B: 0.0 to 1.50 x "rated current" (A)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*1)
00 (disabling the restraint), 01 (decelerating and stagnating),
02 (enabling acceleration with deceleration),
03 (enabling acceleration) (SJ700D only)
330 to 390 (V) (200 V class model), 660 to 780 (V) (400 V class model)
0.10 to 30.00 (s)
0.00 to 2.55
0.000 to 9.999 / 10.00 to 63.53 (s)
00 (disabling), 01 (enabling)
1.to 100.(%)
00 (disabling), 01 (enabling)
00 (Read/Write OK), 01 (Protected)
00 (Initialization disable), 01 (Perform initialization)
(*2) 4000HF: 0.00 to 99.99, 100.0 to 120.0 (Hz)
01 (RV: Reverse RUN), 02 (CF1: Multispeed 1 setting), 03 (CF2: Multispeed 2
setting), 04 (CF3: Multispeed 3 setting), 05 (CF4: Multispeed 4 setting), 06 (JG:
Jogging), 07 (DB: external DC braking), 08 (SET: Set 2nd motor data), 09 (2CH:
2-stage acceleration/deceleration), 11 (FRS: free-run stop), 12 (EXT: external
trip), 13 (USP: unattended start protection), 14: (CS: commercial power source
enable), 15 (SFT: software lock), 16 (AT: analog input voltage/current select), 17
(SET3: 3rd motor control), 18 (RS: reset), 20 (STA: starting by 3-wire input), 21
(STP: stopping by 3-wire input), 22 (F/R: forward/reverse switching by 3-wire
input), 23 (PID: PID disable), 24 (PIDC: PID reset), 26 (CAS: control gain setting),
27 (UP: remote control UP function), 28 (DWN: remote control DOWN function),
29 (DWN: remote control data clearing), 31 (OPE: forcible operation), 32 (SF1:
multispeed bit 1), 33 (SF2: multispeed bit 2), 34 (SF3: multispeed bit 3), 35 (SF4:
multispeed bit 4), 36 (SF5: multispeed bit 5), 37 (SF6: multispeed bit 6), 38 (SF7:
multispeed bit 7), 39 (OLR: overload restriction selection), 40 (TL: torque limit
enable), 41 (TRQ1: torque limit selection bit 1), 42 (TRQ2: torque limit selection
bit 2), 43 (PPI: P/PI mode selection), 44 (BOK: braking conÞ rmation), 45 (ORT:
orientation), 46 (LAC: LAD cancellation), 47 (PCLR: clearance of position
deviation), 48 (STAT: pulse train position command input enable), 50 (ADD:
trigger for frequency addition [A145]), 51 (F-TM: forcible-terminal operation),
52 (ATR: permission of torque command input), 53 (KHC: cumulative power
clearance), 54 (SON: servo-on), 55 (FOC: pre-excitation), 56 (MI1: general-
purpose input 1), 57 (MI2: general-purpose input 2), 58 (MI3: general-purpose
input 3), 59 (MI4: general-purpose input 4), 60 (MI5: general-purpose input 5),
61 (MI6: general-purpose input 6), 62 (MI7: general-purpose input 7), 63 (MI8:
general-purpose input 8), 64 (EMR: Emergency stop) (*1), 65 (AHD: analog
command holding), 66 (CP1: multistage position settings selection 1 ), 67 (CP2:
multistage position settings selection 2), 68 (CP3: multistage position settings
selection 3), 69 (ORL: Zero-return limit function), 70 (ORG: Zero-return trigger
function), 71 (FOT: forward drive stop), 72 (ROT: reverse drive stop), 73 (SPD:
speed / position switching), 74 (PCNT: pulse counter), 75 (PCC: pulse counter
clear), 82 (PRG: EzSQ program) (SJ700D only), no (NO: no assignment)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
Monitored data or setting
(*3) SJ700D (VT): Not available (no display)
Monitored data or setting
［⃝ = Allowed
Default Setting
SJ700/SJ700D(CTmode) SJ700B
(allowed or not)
-FE -FU -F -F -FU
0. 0. 0. 0. 0.
0.0 0.0 0.0 0.0 0.0
0. 0. 0. 0. 0.
0.0 0.0 0.0 0.0 0.0
0. 0. 0. 0. 0.
0.0 0.0 0.0 0.0 0.0
00 00 00 00 00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
Rated current x 1.00
0.00 0.00 0.00 0.00 0.00
00 00 00 00 00
380/760 380/760 380/760 380/760 380/760
1.00 1.00 1.00 1.00 1.00
0.50 0.50 0.50 0.50 0.50
0.060 0.060 0.060 0.060 0.060
× ×
00 00 00
× ×
10. 10. 10.
× ×
00 00 00
× ×
00 00 00
× ×
00 00 00
［⃝ = Allowed
Default Setting
SJ700/SJ700D(CTmode) SJ700B
(allowed or not)
-FE -FU -F -F -FU
18 18 18 18 18
(RS) (RS) (RS) (RS) (RS)
16 16 16 16 16
(AT) (AT) (AT) (AT) (AT)
06 06 06 06 03
(JG) (JG) (JG) (JG) (CF2)
11 11 11 11 02
(FRS) (FRS) (FRS) (FRS) (CF1)
09 09 09 09 01
(2CH) (2CH) (2CH) (2CH) (RV)
03 13 03 03 06
(CF2) (USP) (CF2) (CF2) (JG)
02 02 02 02 11
(CF1) (CF1) (CF1) (CF1) (FRS)
01 01 01 01 13
(RV) (RV) (RV) (RV) (USP)
00 00 00 00 00
00 00 00 00 00
00 00 00 00 00
00 00 00 00 00
00 00 00 00 00
00 01 00 00 00
00 00 00 00 00
00 00 00 00 00
00 00 00 00 00
×
= Not permitted］
Setting Change
during during
operation operation
(allowed or not)
× ×
× ×
× ×
× ×
× ×
× ×
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
○ ○
○ ○
× ○
○ ○
○ ○
× ○
× ×
×
= Not permitted］
Setting Change
during during
operation operation
(allowed or not)
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○