Table of Contents
Advertisement
LME / RSD10 / RSD20 / RSD50 / RSD100 (Contrac) ELECTRICAL LINEAR ACTUATOR | OI/LME/RSD10/100-EN REV. E
Conductor cross-section on electronic unit
Note
Detailed information on separate electronic units can be found
in the corresponding data sheets.
EAN823 – screw terminals
Motor/brake
Mains
Signals
EBN853 – Screw terminals
Motor/brake
Mains
Signals
EBN861 – Screw terminals
Motor / brake
Mains
Signals
EAS822 – Clamping connection
Mains cable
Signal cable (DCS)
Transmitter (option)
Motor cable
Sensor cable
Change from two to one column
2
rigid: 0.2 to 6 mm
(24 to 10 AWG)
2
flexible: 0.2 to 4 mm
(24 to 12 AWG)
2
rigid: 0.5 to 6 mm
(20 to 10 AWG)
flexible: 0.5 to 4 mm
2
(20 to 12 AWG)
2
rigid: 0.5 to 6 mm
(20 to 10 AWG)
2
flexible: 0.5 to 4 mm
(20 to 12 AWG)
rigid: 0.2 to 6 mm
2
(24 to 10 AWG)
flexible: 0.2 to 4 mm
2
(24 to 12 AWG)
2
rigid: 0.5 to 6 mm
(20 to 10 AWG)
2
flexible: 0.5 to 4 mm
(20 to 12 AWG)
2
rigid: 0.5 to 4 mm
(20 to 12 AWG)
2
flexible: 0.5 to 2.5 mm
(20 to 14 AWG)
2
rigid: 0.2 to 6 mm
(24 to 10 AWG)
2
flexible: 0.2 to 4 mm
(24 to 12 AWG)
2
rigid: 0.5 to 6 mm
(20 to 10 AWG)
2
flexible: 0.5 to 4 mm
(20 to 12 AWG)
rigid: 0.5 to 4 mm
2
(20 to 12 AWG)
2
flexible: 0.5 to 2.5 mm
(20 to 14 AWG)
Suited for cable Ø Terminals for conductor
cross-section
13 mm (0.51 in)
max. 4 mm
8 mm (0.31 in)
max. 1.5 mm
8 mm (0.31 in)
max. 1.5 mm
13 mm (0.51 in)
max. 4 mm
8 mm (0.31 in)
max. 1.5 mm
EBS852 – Clamping connection
Mains cable
Signal cable (DCS)
Transmitter (option)
Motor cable
Sensor cable
EBS862 – Clamping connection
Mains cable
Signal cable (DCS)
Transmitter (option)
Motor cable
Sensor cable
Cable glands
The actuators and electronic units are supplied without cable
glands. Suited cable glands must be installed on site.
Tap holes for cable glands
Signals
Motor
*
Adapter for PG or NPT thread must be ordered separately
Selection of suited connection cables
Please observe the following information when selecting cables:
•
Use shielded cables for the motor/brake cable, the
sensor cable, and the signal cable to the control
system/controller.
•
Connect the shielding of the motor/brake cable and the
2
(12 AWG)
sensor cable on both sides (to the actuator and to the
2
(16 AWG)
Contrac electronic unit).
2
(16 AWG)
2
(12 AWG)
2
(16 AWG)
Suited for cable Ø Terminals for conductor
13 mm (0.51 in)
8 mm (0.31 in)
8 mm (0.31 in)
13 mm (0.51 in)
8 mm (0.31 in)
Terminals for conductor cross-section
metric
optional adapters for*
M20 × 1.5 (2 ×)
PG 16 (2 ×)
M25 × 1.5 (1 ×)
PG 21 (1 ×)
19
cross-section
max. 4 mm
2
(12 AWG)
max. 1.5 mm
2
(16 AWG)
2
max. 1.5 mm
(16 AWG)
2
max. 4 mm
(12 AWG)
2
max. 1.5 mm
(16 AWG)
2
max. 6 mm
(10 AWG)
2
max. 4 mm
(12 AWG)
max. 4 mm
2
(12 AWG)
max. 6 mm
2
(10 AWG)
2
max. 4 mm
(12 AWG)
NPT ½ in (2 ×)
NPT ¾ in (1 ×)
Advertisement
Table of Contents
