Mode Check Display - Panasonic AG-CX350 Operating Instructions Manual

*2 Displays when the remaining recording capacity of the memory card or remaining battery level gets low.
*3 Displays when the multidial, <=/&> button, <(> button, or <SET> button is pressed. The display is cleared approximately three seconds after the operation.

Mode check display

The camera settings and status can be displayed on the viewfinder or LCD monitor screen for check.
Press the <DISP/MODE CHK> button for one second or more while displaying the camera image screen to display the STATUS screen of the mode
check.
The display toggles in the order of the STATUS screen, FUNCTION screen, AUDIO screen, SWITCH screen, NETWORK screen and the camera image
screen each time the <DISP/MODE CHK> button is pressed.
Each screen of the mode check is displayed for approximately five seconds.
The screen does not switch while the <DISP/MODE CHK> button is pressed.
Press the <EXIT> button while each screen is displayed to return to the camera image screen.
FUNCTION screen
Displays the video output settings and information of the recording media.
[VIDEO OUT]
[HDR/SDR]
[CARD STATUS]
Chapter 7 Output and Screen Display — Screen status display
Item
[VIDEO OUT SEL]
[SDI OUT FORMAT]/[AV OUT
FORMAT]
[SDI OUT CHAR]/[AV OUT CHAR]
[HDMI OUT FORMAT]
[HDMI OUT CHAR]
[SDI OUT]/[AV OUT]
[HDMI OUT]
[LCD/VF]
—
[TOTAL]
[SLOT1]
[SLOT2]
Displays the output destination of the video and audio with [SDI + HDMI]/[AV +
HDMI].
Displays as follows depending on the setting for the output destination of video
and audio.
f When set to [SDI + HDMI]:
The signal output from the <SDI OUT> terminal is displayed with
[1920×1080p][1920×1080i]/[1920×1080PsF]/[1280×720p]/[720×480i]/
[720×576i].
f When set to [AV + HDMI]:
The signal output from the <AV OUT> terminal is displayed with [720×480i]/
[720×576i].
Displays as follows depending on the setting for the output destination of video
and audio.
f When set to [SDI + HDMI]:
Displays whether to superimpose the character to the output from the <SDI
OUT> terminal with [ON]/[OFF].
f When set to [AV + HDMI]:
Displays whether to superimpose the character to the output from the <AV
OUT> terminal with [ON]/[OFF].
The signal output from the <HDMI> terminal is displayed with [3840×2160p]/
[3840×2160p(420/8bit)]/[1920×1080p]/[1920×1080i]/[1280×720p]/[720×480p]/
[720×576p].
Displays whether to superimpose the character to the output from the <HDMI>
terminal with [ON]/[OFF].
Displays as follows depending on the setting for the output destination of video
and audio.
f When set to [SDI + HDMI]:
The output image from the <SDI OUT> terminal is displayed with [HDR]/
[SDR].
f When set to [AV + HDMI]:
The output image from the <AV OUT> terminal is displayed with [SDR].
The output image from the <HDMI> terminal is displayed with [HDR]/[SDR].
Displays the output image from the LCD monitor and the viewfinder with [HDR]/
[SDR].
Displays the status, remaining recording capacity, and the total capacity of the
memory card inserted in the card slot.
It is not displayed when set to the [NETWORK] menu → [NETWORK FUNC] →
[NDI|HX].
The status of the memory card that is displayed are following types.
f [NO CARD]: Memory card is not inserted.
f [UNSUPPORTED]: Memory card is not supported.
f [FORMAT ERROR]: Memory card cannot be used. (Format error)
f [PROTECTED]: It is write protected. (The write-protection switch of the
memory card is set to the LOCK side)
f [NO REMAIN]: There is no remaining recording capacity.
f [NOT SDXC]: SDXC memory card is not inserted in the MOV recording.
f Cases other than above: The remaining recording capacity is displayed in 0%
through 100%.
Displays the remaining recording capacity/total capacity of the memory cards in
the card slot 1 and the card slot 2.
Displays the status and remaining recording capacity/total capacity of the
memory card in card slot 1.
Displays the status and remaining recording capacity/total capacity of the
memory card in card slot 2.
– 161 –
Description