ABB ABILITY SSC600 Product Manual page 17

Product Guide
SSC600
Product version: 1.0
Table 34. Three-phase overvoltage protection (PHPTOV)
Characteristic
Operation accuracy
Start time UFault = 1.1 × set Start value
33, 34
Reset time
Reset ratio
Retardation time
Operate time accuracy in definite time mode
Operate time accuracy in inverse time mode
Suppression of harmonics
Table 35. Three-phase overvoltage protection (PHPTOV) main settings
Parameter
Start value
Time multiplier
Operate delay time
Operating curve type42
Table 36. Positive-sequence undervoltage protection (PSPTUV)
Characteristic
Operation accuracy
Start time UFault = 0.99 × set Start value
36, 37
UFault = 0.9 × set Start value
Reset time
Reset ratio
Retardation time
Operate time accuracy in definite time mode
Suppression of harmonics
Table 37. Positive-sequence undervoltage protection (PSPTUV) main settings
Parameter
Start value
Operate delay time
Voltage block value
Table 38. Negative-sequence overvoltage protection (NSPTOV)
Characteristic
Operation accuracy
Start time UFault= 1.1 × set Start value
38, 39
UFault = 2.0 × set Start value
33 Start value = 1.0 × Un, Voltage before fault = 0.9 × Un, fn = 50 Hz, overvoltage in one phase-to-phase with nominal frequency injected from random phase angle, results based on
statistical distribution of 1000 measurements
34 Includes the delay of the signal output contact
35 Maximum Start value = 1.20 × Un, Start value multiples in range of 1.10...2.00
36 Start value = 1.0 × Un, positive-sequence voltage before fault = 1.1 × Un, fn = 50 Hz, positive sequence undervoltage with nominal frequency injected from random phase angle, results
based on statistical distribution of 1000 measurements
37 Includes the delay of the signal output contact
38 Negative-sequence voltage before fault = 0.0 × Un, fn = 50 Hz, negative-sequence overvoltage with nominal frequency injected from random phase angle, results based on statistical
distribution of 1000 measurements
39 Includes the delay of the signal output contact
ABB
Value
Depending on the frequency of the measured voltage: fn ±2 Hz
±1.5% of the set value or ±0.002 × Un
Minimum
23 ms
Typically 40 ms
Depends on the set Relative hysteresis
<35 ms
±1.0% of the set value or ±20 ms
±5.0% of the theoretical value or ±20 ms
DFT: -50 dB at f = n × fn, where n = 2, 3, 4, 5,...
Function
PHPTOV
PHPTOV
PHPTOV
PHPTOV
Value
Depending on the frequency of the measured voltage: fn ±2 Hz
±1.5% of the set value or ±0.002 × Un
Minimum
52 ms
44 ms
Typically 40 ms
Depends on the set Relative hysteresis
<35 ms
±1.0% of the set value or ±20 ms
DFT: -50 dB at f = n × fn, where n = 2, 3, 4, 5,...
Function
PSPTUV
PSPTUV
PSPTUV
Value
Depending on the frequency of the measured voltage: fn ±2 Hz
±1.5% of the set value or ±0.002 × Un
Minimum
33 ms
24 ms
Typical
27 ms
35
Value (Range)
0.05...1.60 × Un
0.05...15.00
40...300000 ms
Definite or inverse time
Curve type: 5, 15, 17, 18, 19, 20
Typical
55 ms
47 ms
Value (Range)
0.010...1.200 × Un
40...120000 ms
0.01...1.00 × Un
Typical
35 ms
26 ms
1MRS758725
Maximum
31 ms
Step
0.01
0.01
10
Maximum
58 ms
50 ms
Step
0.001
10
0.01
Maximum
37 ms
28 ms
17