Assy,Chassis R", "Compl, Pipe; And "Cam,Mechanism L; Guide,Cassette R" And "Compl Pwb,Mc-3 - Sanyo DVP-P1EX Technical Information

3-14. "ASSY,CHASSIS R (7A000) ", "COMPL,
PIPE DRUM RUBBER (4A000) ",
"COMPL,GUIDE,PAPER (5I000) ",
"CAM,MECHANISM R (5L000) ", and
"CAM,MECHANISM L (5K000) "
(See Figs. 3-14-1 to 3-14-4)
1) Referring to sections 3-1 through 3-13, remove each part.
2) Remove the "SPECIAL WASHER-7.1X0.8
(Refer to Fig. 3-14-3.)
3) Remove the "SCR S-TPG BIN 2.6X4
(7A000)
"ASSY,CHASSIS R
4) Remove the two "SCR S-TPG BIN 2.6X4
(7A000)
"ASSY,CHASSIS R
5) Pull connector 1 and connector 2 out from each hole.
(Refer to Fig. 3-14-2.)
6) Place the "ASSY,CHASSIS L
the "ASSY,CHASSIS R
7) Pull out the "SHAFT,PULLEY FIX
the two "WASHER Y 8X16X0.25
"SPRING,PRESSURE DRUM
3-14-1.)
8) Remove the "COMPL,PIPE DRUM RUBBER
"COMPL,GUIDE,PAPER
(5L000)
R

", and "CAM,MECHANISM L

ASSEMBLY NOTES:
1. Apply grease (VJ8-0229) as shown in Fig. C of Fig.
3-14-3.
2. Install the "COMPL,GUIDE,PAPER
"CAM,MECHANISM L
(4A000)
DRUM RUBBER
(5K000)
MECHANISM L
"COMPL,GUIDE,PAPER
shown in Fig. D of Fig. 3-14-3.
3. Install the assembly ("COMPL,GUIDE,PAPER
"CAM,MECHANISM L
(4A000)
DRUM RUBBER
(7C000)
"ASSY,CHASSIS L
3-14-4.
4. Install the "CAM,MECHANISM R
and shaft 4 on the "COMPL,GUIDE,PAPER
set into the slots as shown in Fig. E of Fig. 3-14-3.
5. Install the "ASSY,CHASSIS R
G of Fig. 3-14-4.
6. Pass connector 1 and connector 2 through hole 1 and hole
2 on the "ASSY,CHASSIS R
put portion A and portion B over hole 1 and hole 2
respectively. (Refer to Fig. 3-14-2.)
7. Insert dowel 1 into slot 1 and insert dowel 2 into hole 3 as
shown in Fig. 3-14-2. (About slot 1 and hole 3 on the
"GUIDE,PAPER EXIT
3-14-2.)
8. Insert dowel 3 into hole 4 and insert dowel 4 into hole 5 as
shown in Fig. 3-14-2. (About hole 4 and hole 5 on the
"GUIDE,CASSETTE R
3-14-2.)
9. Install the two "SCR S-TPG BIN 2.6X4
"SCR S-TPG BIN 2.6X4
(7A000)
"ASSY,CHASSIS R
10. Do not allow dust or the trash to stick to the surface of the
"COMPL,PIPE DRUM RUBBER
11. Referring to section 3-9, align phase between the "CAM,
(5L000)
MECHANISM R
(5K000)
".
(4B000)
(3B200)
" on the
" side. (Refer to Fig. 3-14-2.)
(6P300)
" on the
" side. (Refer to Fig. 3-14-2.)
(7C000)
" down and remove
(7A000)
".
(4E000)
" and remove
(4C000)
" and the
(4D000)
". (Refer to Fig.
(4A000)
(5I000)
", "CAM,MECHANISM
(5K000)
".
(5I000)
(5K000)
" into the "COMPL,PIPE
". Install the "CAM,
" so that shaft 1 and shaft 2 on the
(5I000)
" are set into the slots as
(5I000)
(5K000)
" and "COMPL,PIPE
") completed in step 2 to the
" as shown in Fig. F of Fig.
(5L000)
" so that shaft 3
(5I000)
(7A000)
" as shown in Fig.
(7A000)
" respectively, and
(6P100)
", refer to Fig. A of Fig.
(3B100)
", refer to Fig. B of Fig.
(6P300)
" and the
(3B200)
", then install the
".
(4A000)
".
" and the "CAM,MECHANISM L
12. Referring to section 3-6, adjust the tension of the
"BELT,MOTOR STEP
13. Referring to section 3-7, adjust the tension of the
"BELT,DRUM
".
",
ASSY,CHASSIS R (7A000)
Connector 1
GUIDE,PAPER
EXIT (6P100)
Portion A
" and
",
" are
Fig. A
GUIDE,PAPER
EXIT (6P100)
–22–
(4J000)
".
(4I000)
".
SHAFT,PULLEY FIX (4E000)
WASHER Y
8X16X0.25 (4C000)
SPRING,PRESSURE
DRUM (4D000)
Fig. 3-14-1
SCR S-TPG BIN 2.6X4
(6P300)
Hole 1
Dowel 1
Dowel 2
Hole 2
Portion B
Connector 2
GUIDE,CASSETTE
R (3B100)
Slot 1
Hole 5
GUIDE,CASSETTE
R (3B100)
Hole 3
Fig. 3-14-2
Dowel 3
SCR S-TPG
BIN 2.6X4
(3B200)
Dowel 4
Fig. B
Hole 4