Disassembling The Main Parts Of The Mechanism; Motor,Fan Dc 1.8W", "Guide, Ink-Svf01/Ex", And "Lever, Cassette Stopper - Sanyo DVP-P1EX Technical Information

3. DISASSEMBLING THE MAIN PARTS
OF THE MECHANISM
POINTS TO NOTE
• Referring to "3. HOW TO REMOVE THE CABINET PARTS"
in the Service Manual, remove the cabinet parts and the
circuit board assembly, and remove the Compl Mechanism.
• The codes (letter and numbers in parentheses) indicate Loc.
No. in the parts list.
• When fitting the parts of the mechanism, refer to the "Assem-
bly Notes", and proceed in the reverse of the dis-assembly
order.
• Clamps and dowels are used to prevent parts coming loose.
When removing a clamp or dowel, be careful not to force it,
as this can result in damage.
• Since the dimension of the screw names in the figures are
subject to change without notice, always refer to the parts
list.
3-1. "MOTOR,FAN DC 1.8W (7M000) ",
"GUIDE,INK-SVF01/EX (03800) ", and
"LEVER,CASSETTE STOPPER
(3A000) "
(See Figs. 3-1-1 to 3-1-2)
1) Remove the two "SCR S-TPG BIN 3X12
remove the "MOTOR, FAN DC 1.8W
Fig. 3-1-1.)
2) Remove the cables from the hook on the "GUIDE, INK-
(03800)
SVF01/EX " as shown in Fig. A of Fig. 3-1-1.
3) Remove the three "SCR S-TPG BIN+W 2X5
the "GUIDE,INK-SVF01/EX
1.)
4) Remove portion A on the "LEVER, CASSETTE STOP-
(3A000)
PER " from hole on the "ASSY, CHASSIS L
(7C000)
" as shown in Fig. B of Fig. 3-1-2.
5) While rotating portion B on the "LEVER, CASSETTE
(3A000)
STOPPER " upper side, remove it from hole on
the "ASSY, CHASSIS L
6) Pull portion C on the "LEVER, CASSETTE STOPPER
(3A000)
" out from hole on the "ASSY, CHASSIS L
(7C000)
" and remove the "LEVER, CASSETTE STOP-
(3A000)
PER ". (Refer to Fig. 3-1-2.)
ASSEMBLY NOTES:
1. Insert the two dowels on the "GUIDE, INK-SVF01/EX
(03800)
" into holes on the "ASSY, CHASSIS L
and install the "GUIDE, INK-SVF01/EX
sliding it upwards. (Refer to Fig. 3-1-1.)
2. Place portion D on the "LEVER, CASSETTE STOPPER
(3A000)
" in the reverse side of portion E on the "LEVER,
(1D000)
TPH ADJUST
and verify that the "LEVER, TPH ADJUST
moves smoothly by flicking it.
(7P000)
(7M000)
". (Refer to
(03810)
(03800)
". (Refer to Fig. 3-1-
(7C000) ". (Refer to Fig. 3-1-2.)
(7C000)
(03800)
" as shown in Fig. B of Fig. 3-1-2,
(1D000)
GUIDE,INK-SVF01/EX (03800)
SCR S-TPG BIN+W
2X5 (03810)
Dowel
Dowel
" and
ASSY,CHASSIS L (7C000)
Hook
" and
ASSY,
CHASSIS L
(7C000)
LEVER,CASSETTE
STOPPER (3A000)
Fig. B
",
" by
ASSY,
CHASSIS L
(7C000)
"
LEVER,TPH
ADJUST
(1D000)
–8–
MOTOR,FAN DC 1.8W (7M000)
SCR S-TPG BIN 3X12 (7P000)
Holes
Cable
GUIDE,INK-SVF
01/EX (03800)
Fig. 3-1-1
Portion E
Portion A
Portion B
Portion C
Portion D
LEVER,CASSETTE
STOPPER (3A000)
Fig. 3-1-2
Fig. A