Selecting A Key Fill; Selecting A Key Source - Sony XVS-9000 User Manual

When key wipe pattern key is selected
No. Parameter Adjustment
1 SIZE Pattern size
2 SOFT Degree of edge softness
3 DENSITY Key density

Selecting a Key Fill

Set a key fill using the key fill/key source selection
buttons.
When using a color matte
Press the [PAGE] button to display the page 2/3 setting
buttons, then press the [MAT FILL] button.
The [MAT FILL] button turns on green, and displays the
parameter name and value of each parameter item on the
display.
When [Flat Color] is selected in the Type >Matte Adjust
menu, set the following parameters.
No. Parameter Adjustment
1 LUM Color 1 luminance
2 SAT Color 1 saturation
3 HUE Color 1 hue
When [Mix Color] is selected in the Type >Matte Adjust
menu, set the following parameters.
Parameter group [1/2]
No. Parameter Adjustment
1 LUM Color 1 luminance
2 SAT Color 1 saturation
3 HUE Color 1 hue
4 SIZE Pattern size
5 SOFT Degree of softness of pattern edge
Parameter group [2/2]
No. Parameter Adjustment
1 LUM Color 2 luminance
2 SAT Color 2 saturation
3 HUE Color 2 hue
4 SIZE Pattern size
5 SOFT Degree of softness of pattern edge
When using a key fill bus signal
Press the [PAGE] button to display the page 2/3 setting
buttons, then press the [MAT FILL] button, turning it off.
Using any of the following methods, select the key fill
signal.
• On the cross-point control block, press a key bus
delegation button on the cross-point pad and select a
signal using the cross-point buttons.
• On the cross-point control block in key/AUX bus
delegation mode, press a key bus delegation button in the
1st row and select a signal using the cross-point buttons
in the 2nd row.
Note
You can assign a key fill bus delegation button to the 1st
row or 2nd row of the AUX bus control block (AUX bus
operation mode) in the Setup menu (see page 410).

Selecting a Key Source

Set a key source using the key fill/key source selection
buttons.
When using a selected key fill and paired key
source signal
Press the [AUTO SEL] button, turning it on.
When using a signal other than the selected key
fill paired signal
Press the [SPLT] button, turning it on.
Using any of the following methods, select the key source.
• On the cross-point control block, press and hold a key
bus delegation button on the cross-point pad and select a
signal using the cross-point buttons in the 2nd row.
• Press and hold the [SPLT] button in the key control
block, then select a signal using the cross-point buttons
in the 2nd row in the cross-point control block.
• On the Flexi Pad control block in key operation mode,
press and hold a key delegation button in the memory
recall section and select a signal using the cross-point
buttons in the 2nd row in the cross-point control block.
• On the cross-point control block in key/AUX bus
delegation mode, press and hold a key bus delegation
button in the 1st row and select a signal using the cross-
point buttons in the 2nd row.
Notes
• On the cross-point control block in key bus mode or free
assign mode, you can select a key fill signal in the 1st
row and a key source signal in the 2nd row by pressing
and holding the following buttons.
- Key bus delegation buttons on the cross-point pad
- [SPLT] button on the key control block
- Key delegation buttons in the memory recall section
on the Flexi Pad control block (key operation mode)
• You can assign a key source bus delegation button to the
1st row or 2nd row of the AUX bus control block (AUX
bus operation mode) in the Setup menu (see page 410).
• To select a video signal, first set the [KEY] button
operation mode in the Setup menu (see page 111).
124