Related Manuals for Toro Workman 07347
Summary of Contents for Toro Workman 07347
- Page 1 Form No. 3392-713 Rev B 1/3 Area Platform Lift Workman ® Heavy-Duty Utility Vehicle Model No. 07347—Serial No. 315000001 and Up *3392-713* B Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Checking the Oil Level ........18 additional information, contact an Authorized Service Checking the Tire Pressure....... 18 Dealer or Toro Customer Service and have the model Engaging Safety Locks ........18 and serial numbers of your product ready. Operating the Lift ..........19 This manual identifies potential hazards and has Operating Tips .......... -
Page 3: Safety
• Do not drop or throw articles from a raised quickly. A replacement manual is available at platform. www.Toro.com. • When raising the platform, be aware of overhead • Do not allow children to operate the lift. Do not obstructions that could cause bodily injuries. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal93-3701 93-3701 decal93-3703 93-3703 decal93-3702 93-3702 decal93-3704 93-3704 decal93-3706 93-3706... - Page 5 decal93-3709 93-3709 decal93-3711 93-3711 decal93-3710 93-3710 decal93-3705 93-3705 decal93-3707 93-3707...
-
Page 6: Setup
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare to install the kit. Remove the center console, seat – No parts required shroud, and seat assemblies. Remove the CVT cooling duct –... -
Page 7: Preparing To Install The Kit
Preparing to Install the Kit Removing the Center Console, Seat Shroud, and No Parts Required Seat Assemblies For Workman 3000 and Workman No Parts Required 4000 Series machines with Serial Numbers 240000001 and Up Removing the Center Console for Position the machine on a clean, level surface, Workman 3000, 4000, HD, HDX, shut off the engine, engage the parking brake, and HDX-D Machines... - Page 8 g023165 Figure 3 g024571 Figure 4 1. Screw 2. Cover plate 1. Brake lever 5. Transmission lever (L position) knob Disconnect the reservoir hose from the radiator 2. Hydraulic-lift lever knob 6. Hydraulic-lift lock (locked and plug or clamp it to retain coolant (Figure position —...
-
Page 9: Removing The Cvt Cooling Duct (Hdx-Auto Only)
Removing the Seats from the Machines Remove the 8 socket-head bolts that secure the seat rails of the seat to the chassis and remove the seats (Figure g024791 Figure 7 1. CVT intake hose 3. Intake-tube connector 2. Hose clamp Installing the Main Wire g023164 Figure 6... -
Page 10: Mounting The Parking Brake Switch
Remove the fasteners securing the wire harness Remove the fasteners securing the wire harness cover to the underside of the machine floor and cover to the underside of the machine floor and remove the cover. remove the cover. Route the wire harness rearward to the console Route the wire harness rearward to the console area. - Page 11 g028255 Figure 10 1. Target icon on the switch 2. Gap (between 0.06 and 0.1 inch) Ensure that the gap between the head of the clevis pin and the switch should be between 0.06 and 0.1 inch. Note: If the gap is not correct, adjust the head of the pin by moving the position of the washers installed in steps and 4.
-
Page 12: Mounting The Rear Level Switch
Mounting the Parking Brake Switch Workman Models with a Manual Transmission Mount the parking brake switch to the parking brake mount with 2 screws as shown in Figure g016822 Figure 12 1. Hitch plate 2. Level switch bracket g007162 Using the upper set of mounting holes, mount Figure 11 the level switch bracket to the rear axle with the locknuts previously removed. -
Page 13: Installing The Hood, Rops Shield Shroud, Seats, Seat Shroud, Console Cover Plates, And Cvt Intake Hose (Hdx-Auto Only)
bracket to the rear axle with the capscrews previously removed. Note: Position the washers between the hitch plate and axle. Mounting the Lift onto the Tighten the 4 capscrews. Machine Frame Route the switch harness forward, along shift the cable to the left side of the machine. Note: Parts needed for this procedure: The harness must not interfere with any... -
Page 14: Connecting The Wire Harness And Battery
Note: To prevent the lift scissor arms from expanding, pick up the platform lift from the bottom when positioning it on the frame. Position the lift onto the frame, aligning the Connecting the Wire mounting holes with the holes in the frame (Figure 16). -
Page 15: Mounting The Bubble Level Indicator
Mounting the Bubble Level Indicator Parts needed for this procedure: Bubble level indicator Procedure Affix the bubble level indicator to the top of the console g017228 Figure 17 cover as shown in Figure 1. Positive lift wire 3. Red wire from front harness 2. -
Page 16: Installing The Decals
For Workman HD, HDX, HDX-D, and HDX-Auto Machines Affix the operation decal to the top of the console cover as shown in Figure Installing the Decals Affix the no-step decals to the top of the radiator as shown in Figure Parts needed for this procedure: Operation decal No-step decal... -
Page 17: Product Overview
Key Switch Product Overview Rotate the key switch to authorize the use of the lift. Remove the key from the lift pendant control switch to Controls prevent operation of the lift whenever the machine is left unattended (Figure 21). Emergency Lowering Valve Knob Push the blue knob inward, rotate it 90 degrees counterclockwise, and pull it out to activate the emergency lowering valve... -
Page 18: Operation
Checking the Tire Pressure Operation Check the tire pressure every 8 hours or daily to Checking the Oil Level ensure proper levels. Refer to the machine Operator’s Manual for tire Capacity: 1.5 US qt inflation specification. The lift reservoir is filled at the factory with 5W30 oil. Check the level before the lift is first operated and Engaging Safety Locks every 8 hours or daily, thereafter. -
Page 19: Operating The Lift
Operating the Lift The 1/3 platform lift is designed to be used only with a Workman machine and must be mounted with the wire harness, level, decals, switches, and all the interlock switches installed. DANGER Improper operation of the platform lift may cause serious personal injury or death. - Page 20 DANGER DANGER If you move the vehicle with the platform Contact between the non-insulated in the raised position, a loss of control platform lift and power lines will cause or tip-over will result, causing possible electrocution, causing serious injury or serious personal injury to you or death.
-
Page 21: Operating Tips
Emergency Lowering Operating Tips Push the blue knob inward, rotate it 90 degrees The electrical system, battery, and hydraulic lift counterclockwise, and pull it out to activate the cylinder are not designed for continuous use. emergency lowering valve (Figure 22). Allow approximately 1-1/2 to 2 minutes between lift operations to maintain the operating temperature. -
Page 22: Maintenance
Maintenance Testing the Rear Axle-Level Switch Position one side of machine so that the rear axle is on a slope greater than 5 degrees. Checking the Safety Note: The slope can be a floor jack, mound of Circuits material, or a small hill. Engage the parking brake and chock the wheels. -
Page 23: Maintaining The Battery
Maintaining the Battery WARNING Service Interval: Every 50 hours CALIFORNIA The battery electrolyte level must be properly Proposition 65 Warning maintained and the top of the battery kept clean. If the Battery posts, terminals, and related machine is stored in a location where temperatures accessories contain lead and lead are extremely high, the battery will run down more compounds, chemicals known to... - Page 24 Notes:...
- Page 25 Notes:...
- Page 26 Notes:...
- Page 27 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 28 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.