CONTENTS GENERAL RECOMMENDATIONS............Page HANDLING ........................Page UNPACKING ........................Page DISPOSAL........................Page TECHNICAL DATA......................Page INSTRUCTIONS FOR THE INSTALLER/MAINTENANCE PERSON ..Page WATER CONNECTION ....................Page ELECTRICAL CONNECTION ..................Page DETERGENT/RINSE-AID DISPENSERS AND SETTINGS..........Page SETTING THE DISPENSERS..................Page MAINTENANCE....................... Page INSTRUCTIONS FOR THE USER............
GENERAL RECOMMENDATIONS Lift the appliance using a lift truck, remove the base WARNING and position the appliance CAREFULLY READ THE INSTALLATION, OPERA- TING MAINTENANCE INSTRUCTIONS BEFORE INSTALLING THIS APPLIANCE. INCOR- RECT INSTALLATION, ADAPTATIONS OR ALTER- NATIONS COULD CAUSE DAMAGE TO PROPERTY OR INJURY TO PERSONS.
Page 4
Figure 4 Legend Figure 4 A - Water inlet pipe with ø 3/4” G fittings C - Outlet pipe øi 40 mm (^) – øi 18mm (*). - Power supply S - Pipe inlet for detergents Q - Unipotential screw (^) - Only for model with free-fall drainage (*) - Only for model with drain pump...
B INSTRUCTIONS FOR THE INSTALLER/MAINTENANCE PERSON Install a disconnecting switch with a capacity at Make four ø 9mm though holes in the support, res- least equal to that given in the technical data table, pecting distances given in Figure 7. a 30mA residual current circuit breaker and an overcurrent device (magnetothermal cut-out with 431 mm...
On the model with free-fall drainage: Three-phase version: Power supply 400…415V 3N connect the waste outlet pipe “C” (Figure 4) to the main drain pipe, fitting a trap, or place the outlet pipe over an S trap set into the floor. On the model with drain pump: position the outlet pipe at a height anywhere between 750 and 1000 mm from the floor.
Connections provided for energy control. Insert the hose provided in the kit into the detergent container. This appliance is designed for an external energy con- sumption control. 2. Dishwashers with incorporated peristaltic rinse-aid dispenser pump (Figure 16). Pump “S” dispenses about 0.1 g/s of rinse-aid. It dispenses 0.3 g in 3 sec.
Electrical connections for automatic detergent and rinse-aid dispensers. Single-phase version: The appliance has a terminal board for the power sup- ply of dispensers operating at 230 V, max. power DETERGENT DISPENSER DISPENSER RINSE-AID 30VA. In the appliances with pressure boiler, the diaphragm Connect to the terminal board “L”...
Amount of detergent during the cycle: 2) Rinse-aid diaphragm dispenser To change the dispensed amount, turn on screw “D” accordingly (Figure 16). Suggestion: to check the effectiveness of the rinse- Setting the activation time: aid, look at freshly washed glasses against the light. Drops of water remaining on the glass indicate an insufficient amount while streaks indicate an excess.
INSTRUCTIONS FOR THE USER Our appliances have been studied and optimised to give high performance. This appliance must be used exclusively for the purpose for which it has been designed, i.e. for washing dishes with water and specific detergents. Any other use is to be considered improper.
55°C To display the boiler temperature during heating of the tank, open the door and press the button “F” (Figure 19). - Cycle III For very dirty dishes: press button “H” (Figure 19) (see table of times). WASH CYCLES • To stop the wash cycle, just press the cycle button The wash cycle includes one wash with hot water and or open the door.
Type of racks and loading Figure 20 Figure 26 • YELLOW rack: for 18 plates with maximum diame- • Half size basket for glasses (500X250 mm) ter of 240 mm. Available as accessories: dividers for glasses and rack for dishes with maximum diameter of 320 mm. Note: if only one type of dish rack is to be used, it is advisable to choose the GREEN rack.
• Replace the filters and the overflow. To reduce the emission of pollutants into the environ- • Unscrew the ring nuts “H” and remove the header units “C”. ment, clean the appliance (externally and where necessary internally) with products having a biodegra- dability of over 90%.
TROUBLESHOOTING DISHWASHER DOES NOT WASH 1. Check if the suction filter is dirty and clean it thoroughly. WELL 2. Check if the wash jets are clogged by solid food remains. 3. Check that the initial amount of detergent or subsequent additions are correct.