Related Manuals for Toro Reelmaster 33145
Summary of Contents for Toro Reelmaster 33145
- Page 1 Form No. 3432-251 Rev A Universal Frame Reelmaster ® Gang Mowers Model No. 33145—Serial No. 404400001 and Up Model No. 33155—Serial No. 404400001 and Up *3432-251* A Register at www.Toro.com. Original Instructions (EN)
- Page 2 Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product.
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 General Safety General Safety ........... 3 Safety and Instructional Decals ......3 • Read and understand the contents of both this Setup ................ 4 Operator’s Manual and the operator’s manual of 1 Setting Up the Stationary Cutting the traction unit before using this machine. -
Page 4: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Frame support Large cotter pin Center frame Trailing frame Stationary drawbar Locknut (1/2 inch) Spacer Set up the stationary cutting units. Bolt (1/2 x 2-1/2 inches) Bolt (1/2 x 1-1/4 inches) Small cotter pin Shackle... - Page 5 Media and Additional Parts Description Qty. Operator's Manual Read before operating. Note: Determine the left and right sides of the machine from the normal operating position. g289206 Figure 3 1. Bolt (1/2 x 1-1/4 inch) 8. Spacer 15. Stationary drawbar 22.
-
Page 6: Setting Up The Stationary Cutting Units
(Figure 5). Contact your local authorized Setting Up the Stationary Toro distributor to order parts or for assistance. Cutting Units Model 33145 for 3 Cutting Units Parts needed for this procedure: Frame support... -
Page 7: Installing The Wing Frames
This feature allows the frame sections to be placed and track within a 2.4 m (8 ft) width for transport purposes or when narrow areas must be mowed; for more info contact your authorized Toro distributor. Locate and drill the required mounting holes in... -
Page 8: Completing The Installation
g289160 Figure 9 1. Trailing hitch 4. 7 cm (2-3/4 inches) 2. Wing frame 5. Drill a 13.5 cm (17/32 inch) diameter hole here. 3. 3.5 cm (1-3/8 inches) 6. 1.9 cm (3/4 inch) g289161 Figure 8 Pull the entire trailing unit forward and insert the 1. -
Page 9: Product Overview
Product Overview Operation Note: Determine the left and right sides of the Specifications machine from the normal operating position. General Specifications Before Operation Cutting Units Width of Cut Approximately 2.1 Approximately 3.4 Before Operation Safety m (7 ft) m (11 ft) Overall Width —... -
Page 10: During Operation
During Operation • Evaluate the site conditions to determine if the slope is safe for machine operation, including surveying the site. Always use common sense and good judgment when performing this survey. During Operation Safety • Review the slope instructions, listed below, for operating the machine on slopes. -
Page 11: After Operation
Hauling the Machine After Operation • Use care when loading or unloading the machine into a trailer or truck. After Operation Safety • Use full-width ramps for loading machine into trailer or truck. General Safety • Tie the machine down securely using straps, •... -
Page 12: Maintenance
Check their proper operation regularly. • Altering this machine in any manner may affect the operation of the machine, performance, durability, or its use may result in injury or death. Such use could void the product warranty of The Toro® Company. -
Page 13: Storage
Paint all scratched or bare metal surfaces. Paint is available from your authorized Toro distributor. Store the machine in a clean, dry garage or storage area. Cover the machine to protect it... - Page 14 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 15 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.