OUTDOOR AIR FILTER F7 CONTROL PANEL HEAT RECOVERY CELLS (2) CARBON DIOXIDE SENSOR SUMMER/WINTER DAMPER HUMIDITY SENSOR INTERNAL HUMIDITY SENSOR OUTDOOR AIR FILTER G4 (BEHIND THE ELECTRIC BOX) EXTRACT AIR FILTER G4 NOTE: For more detailed instructions, go to www.airflow.com...
Page 6
DV245 INTRODUCTION GENERAL SAFETY INSTRUCTIONS For safe and proper handling, it is necessary to know the basic safety regulations and the intended usage of the ventilation system. Read this manual before operating the ventilation unit. Keep this manual for later use. In case of loss, you can download the manual from our website.
Page 8
DV245 INTRODUCTION INTRODUCTION WARNING Ventilation has to be constant for the indoor air to stay healthy for the dwellers and the structures of the dwelling. Even for longer The unit is not intended for use holidays, it is not advisable to stop the ventilation, because the by children under 8 or by persons indoor air will become stuffy and, during the heating season, the with reduced sensory, physical or...
Page 10
DV245 BASIC SETTINGS SET THE 24 OR 12 HOUR CLOCK By default, the system uses a 24 hour clock. If you want to use the 24 hour clock, proceed to the next step by pressing the Arrow right button. If you want to use the 12 hour clock, proceed as follows: Press the Minus button.
Page 12
DV245 EXPERT SETTINGS FAN SETTINGS To set the output ratio between the supply and extract air fans: WARNING The ventilation specialist has made IMPORTANT the supply and exhaust air settings Adjust the air flows according to the values specified in the when deploying the ventilation ventilation plan.
Page 14
DV245 EXPERT SETTINGS AWAY PROFILE When you want to make the Away profile settings, proceed as follows: 1. The deployment wizard Away profile screen is opened. NOTE Once you have set the fan speed for the At home profile, the fan speed for the Away profile will default to -30% of the At home profile fan speed.
Page 16
DV245 EXPERT SETTINGS FIREPLACE PROFILE When you want to make the Fireplace function settings, proceed as follows: 1. The deployment wizard Fireplace function profile screen is opened. 2. Set the profile timer duration in minutes by using the Plus and Minus buttons.
Page 18
DV245 CHANGING THE PROFILE If you want to change the ventilation profile, proceed as follows: 1. Press the Change profile button until the desired ventilation profile icon is displayed in the screen. 2. Wait until the ventilation profile main screen is displayed. 3.
Page 20
DV245 VENTILATION PROFILES VIEWING TEMPERATURE DATA Select Settings > Temperatures and sensors. Select OK. The summary display of temperatures and sensors shows the following information: • Indoor — Indicates the temperature of the air flowing into the unit to be removed from the premises. •...
DV245 TEMPERATURES AND SENSORS VIEWING HUMIDITY AND CARBON DIOXIDE STATISTICS When you want to view statistics on the humidity and carbon dioxide values, proceed as follows: Select Settings > Temperatures and sensors. Press the OK button. The temperature and sensors summary screen is opened. Press the Right arrow button.
Page 24
DV245 SETTINGS FILTER MAINTENANCE REMINDER The maintenance reminder reminds you of the filter replacement with a pop-up window. The message can be accepted by selecting OK. Press the clock button to postpone the reminder for one week. DISPLAY SETTINGS SETTING THE SLEEP TIME The control panel automatically switches to sleep mode when the pre-set sleep time has elapsed.
Page 26
DV245 SETTINGS SETTING THE DATE Select Settings > Time and date. Select OK. Press the Right arrow until the 4/4 display opens. Use the Plus and Minus buttons to set the date. Select Right arrow. Use the Plus and Minus buttons to set the month. Select Right arrow.
Page 28
DV245 SETTINGS EXAMPLE OF SETTING A WEEKLY PROGRAM In this example, the following weekly program has been set: • Mon-Fri 08:00-17:00, Away from home. • Mon-Fri 17:00-08:00, At home. Sat 08:00-18:00, At home. • • Sat 18:00-21:00, Boost that might be needed for cooking. Sat 21:00 - Mon 08:00, At home.
Page 30
DV245 MAINTENANCE To change the filters: Disconnect the ventilation unit from the mains electricity supply. Open the upper door of the unit. Remove the old filters (A, B, C) and discard them. Install the new filters (A, B, C). Close the door of the unit. Ensure that the safety switch of the door is engaged, allowing the unit to be turned on.
Page 32
DV245 MAINTENANCE REMOVING THE ELECTRIC 10 x HEATER To remove the heater: Disconnect the ventilation unit from the mains electricity supply. Open the doors of the unit. Open the heater box by undoing the mounting screws (10 PZ2 screws). Remove the quick connector of the heater: a.
Install the second outlet in the same way. To reassemble the ventilation unit, follow the above steps in reverse order. MEASURING TUBES The accessories delivered with the unit include four airflow measuring tubes. These can be inserted in the ducts to allow for easier ventilation adjustment.
Page 36
DV245 TECHNICAL SPECIFICATIONS DV245 ADROIT MAIN PARTS DIMENSIONS AND DUCT OUTLETS Dimensions 1038 Model R in the figure. In the L model, the parts are mirrored 1 Extract air fan 6 Outdoor air filter G4 2 Supply air fan 7 Extract air filter G4 3 Outdoor air filter F7 8 Optional Post-heating 1038...
DV245 HEATING AND COOLING RADIATOR OPERATION CHARTS RADIATOR (REVERSE CONNECTION) SUPPLY OUTDOOR Adroit ventilation unit INPUT FROM THE DISTRIBUTION BOARD HEAT PUMP HEAT COLLECTION CIRCUIT OPERATION AND SAMPLE CONNECTION NOTE: HEATING Always follow first and foremost the connection diagram provided by the HVAC designer or heat pump manufacturer. The pump starts when the outdoor The accompanying figure shows an example of the arrangement air temperature drops below the...
A1:2011 This is the original Declaration of Conformity Alan Siggins Date 6 May 2016 Managing Director Airflow Developments Limited Aidelle House, Lancaster Road, Cressex Business Park High Wycombe, Buckinghamshire. HP12 3QP, U.K. T: +44 (0)1494 425252 E: info@airflow.com W: airflow.com...
• Has been installed in accordance with latest Building Regulations and IEEE wiring regulations by a recognised competent installer. Airflow Developments Ltd shall not be liable for any loss, injury or other consequential damage, in the event of a failure of the...