Related Manuals for Fujitsu MB2198-503-E
Summary of Contents for Fujitsu MB2198-503-E
- Page 1 FUJITSU MICROELECTRONICS SS01-71096-1E SUPPORT SYSTEM DSU-FR EMULATOR MC-16FX LQFP-64P HEADER TYPE 3 MB2198-503-E OPERATION MANUAL...
- Page 2 MC is the abbreviation of FUJITSU Flexible Microcontroller. *2 : The package is the FPT-64P-M24 (0.5mm lead pitch, 10mm × 10mm body size). *3 : FR, the abbreviation of FUJITSU RISC controller, is a line of products of FUJITSU MICRO- ELECTRONICS LIMITED.
- Page 3 (i.e., submersible repeater and artificial satellite). Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.
-
Page 4: Handling Precautions
1. CHECKING THE DELIVERED PRODUCT Before using the header board, confirm that the following components are included in the box: • LQFP-64P header board* • Screws for securing the header board (M2 × 10mm, 0.4mm pitch) • Washers • NQPACK064SD-ND* •... - Page 5 3. NOTES ON DESIGNING ■ Notes on designing the printed circuit board for the user system If the header board is connected to a user system, the heights of parts mounted around the header board are restricted. When designing the printed circuit board of the user system, consider the height of the parts within range of the header board as shown in Figure 1 such that components mounted on the user system and the header board do not interfere with each other.
- Page 6 ■ MCU footprint design notes Figure 2 shows the recommended dimensions of the footprint for mounting the NQPACK on the printed circuit board of the user system. The printed circuit board of the user system must be designed with due consideration given to this footprint as well as to the mass production MCU.
- Page 7 4. PROCEDURE FOR CONNECTING TO THE USER SYSTEM Before using the header board, mount the supplied NQPACK on the user system. The header board is connected to the adapter board using the 2 flat cables (standard or long) included with the adapter (which is sold separately). See the operation manual of the adapter for details on how to connect the flat cables.
- Page 8 Screws for securing the header board Washer Header board YQPACK NQPACK User system Figure 4 Header board connection ■ Disconnection To disconnect the header board from the user system, remove all four screws, and then pull the head- er board vertically out from the NQPACK.
- Page 9 5. MOUNTING MASS PRODUCTION MCUs Use the supplied HQPACK to mount a mass production MCU on the user system. ■ Mounting 1. Align the index mark (▲) on the NQPACK mounted on the user system with the index mark (●) on the mass production MCU and mount the MCU on the NQPACK.
-
Page 10: Connector Pin Assignment
6. CONNECTOR PIN ASSIGNMENT The signals from the evaluation MCU that is mounted on the adapter board are connected to the YQ- PACK (which has the same pin configuration as the production MCU) via flat cable connectors A and B on the header board. The adapter board and header board are connected using the 2 flat cables (standard or long) that are included with the adapter (which is sold separately). - Page 11 Table 1 Pin assignment of flat cable connector A Connector Evaluation MCU Mass production Connector Evaluation MCU Mass production pin number pin number MCU pin number pin number pin number MCU pin number ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯...
- Page 12 Table 2 Pin assignment of flat cable connector B Connector Evaluation MCU Mass production Connector Evaluation MCU Mass production pin number pin number MCU pin number pin number pin number MCU pin number AH13 AJ13 AJ12 AK12 AJ11 AH12 AK11 AK10 AH11 AG11...
- Page 13 SS01-71096-1E FUJITSU MICROELECTRONICS • SUPPORT SYSTEM DSU-FR EMULATOR MC-16FX LQFP-64P HEADER TYPE 3 MB2198-503-E OPERATION MANUAL July 2008 the first edition Published FUJITSU MICROELECTRONICS LIMITED Edited Business & Media Promotion Dept.