Mitsubishi Electric MELSEC Q Series User Manual page 70

3 SPECIFICATIONS
Address
(Hexadecimal (Decimal))
CH1 CH2
2D 4D
H H
(45) (77)
2E 4E
H H
(46) (78)
2F 4F
H H
(47) (79)
30 50
H H
(48) (80)
31 51
H H
(49) (81)
32 52
H H
(50) (82)
33 53
H H
(51) (83)
34 54
H H
(52) (84)
35 55
H H
(53) (85)
36 56
H H
(54) (86)
37 57
H H
(55) (87)
38 58
H H
(56) (88)
39 59
H H
(57) (89)
3A 5A
H H
(58) (90)
3B 5B
H H
(59) (91)
3C 5C
H H
(60) (92)
3D 5D
H H
(61) (93)
3E 5E
H H
(62) (94)
3F 5F
H H
(63) (95)
A0 (160)
H
A1 (161)
H
A2 (162)
H
A3 (163)
H
A4 (164)
H
A5 (165)
H
A6 (166)
H
A7 (167)
H
A8 (168)
H
A9 (169)
H
AA (170)
H
3 - 32
Downloaded from ManualsNet.com
Settings
CH3 CH4
Sensor compensation value
6D 8D
H H
setting
(109) (141)
Adjustment sensitivity (dead band)
6E 8E
H H
(110) (142) setting
6F 8F
H H
Control output period setting
(111) (143)
70 90
H H
Primary delay digital filter setting
(112) (144)
71 91
H H
Control response parameter
(113) (145)
72 92
H H
AUTO/MAN mode switching
(114) (146)
73 93
H H
MAN output setting
(115) (147)
74 94
H H
Setting change rate limiter
(116) (148)
75 95
H H
AT bias
(117) (149)
76 96
H H
Forward/reverse action setting
(118) (150)
Upper setting
77 97
H H
(119) (151) limiter
Lower setting
78 98
H H
(120) (152) limiter
79 99
H H
Reserved
(121) (153)
Heater disconnection alert setting
7A 9A
H H
(122) (154) 2
Loop disconnection detection
7B 9B
H H
(123) (155) judgment time
Loop disconnection detection
7C 9C
H H
(124) (156) dead band
7D 9D
H H
Unused channel setting
(125) (157)
2
7E 9E
E PROM's PID constant read
H H
(126) (158)
command
Automatic backup setting after
7F 9F
H H
auto tuning of PID constants
(127) (159)
Reserved
Reserved
Reserved
Reserved
Alert dead band setting
Alert delay count
Heater disconnection/output off-
time current error detection delay
count 2
Temperature rise completion
range setting
Temperature rise completion soak
time setting
PID continuation flag
Heater disconnection
compensation function selection
2
1 : This setting may be changed only in the setting mode. Note that changing it in the operation mode will
result in a write data error (error code: 3). Also, Setting change command (YnB) must be turned on to
change the setting.
2: Available only for the Q64TCTTBW and Q64TCRTBW.
3: Indicates whether reading from and writing to a sequence program are enabled.
R : Reading enabled
W : Writing enabled
search engine
Range
-5000 to 5000
(-50.00 to 50.00%)
1 to 100(0.1 to 10.0%)
1 to 100(s)
0 to 100(s)
0: Slow, 1: Normal, 2: Fast
0: Auto (AUTO),
1: Manual (MAN)
-50 to 1050
(-5.0% to 105.0%)
0 to 1000
(0.0 to 100.0%/min)
±input range width
0: Forward action,
1: Reverse action
Q64TCTT(BW)
Within measurement range
Q64TCRT(BW)
Q64TCTT(BW)
Q64TCRT(BW)
—
0 to 100%
0 to 7200s
Input range width
0: Used, 1: Unused
0: Without command,
1: With command
0: OFF, 1: ON
—
0 to 100(0.0 to 10.0%)
0 to 255 (times)
3 to 255 (times)
1 to 10 (°C)
0 to 3600 (min)
0: Stop, 1: Continue
0: OFF, 1: ON
MELSEC-Q
Initial Read/ Reference
value write 3 section
Section
0 R/W
3.5.19
Section
5 R/W
3.5.20
Section
30 R/W
3.5.21
Section
0 R/W
3.5.22
Section
0 R/W
3.5.23
Section
0 R/W
3.5.24
Section
0 R/W
3.5.25
Section
0 R/W
3.5.26
Section
0 R/W
3.5.27
Section
1 R/W
3.5.28
1300 Section
R/W
6000 3.5.29
0
R/W
-2000
— — —
Section
0 R/W
3.5.30
Section
480 R/W
3.5.31
Section
0 R/W
3.5.32
Section
0 R/W
3.5.33
Section
0 R/W
3.5.34
Section
0 R/W
3.5.35
— — —
Section
5 R/W
3.5.36
Section
0 R/W
3.5.37
Section
3 R/W
3.5.38
Section
1 R/W
3.5.39
Section
0 R/W
3.5.40
Section
0 R/W
3.5.41
Section
0 R/W
3.5.42
3 - 32