Panasonic WV-SW395APJ Operating Instructions Manual page 108

11 Configure the settings relating to images and audio [Image/Audio]
•
Off: Mask areas will not be set automatically. It is necessary to set them manually.
•
Default: Off
[Mask area]
When "Off" is selected for "Wide dynamic range" and "Back light compensation (BLC)", it is possible to
compensate for backlight by masking brighter areas.
Refer to page 111 for information on how to set the mask area.
[Light control mode]
Select the light control mode from the following.
•
Outdoor scene: Depending on the brightness level (illuminance), the iris will automatically be controlled
together with the shutter speed adjustment to control light. When shooting a bright subject such as outdoor,
etc., select this parameter. Be aware that flicker may occur when a subject is under fluorescent lighting.
•
Indoor scene (60 Hz) / Indoor scene (50 Hz): The shutter speed will automatically be adjusted to prevent
flicker caused by fluorescent light. Select 50 Hz or 60 Hz corresponding to the location where the camera
is in use.
•
Fix shutter: The selected value will be set as the fixed shutter speed.
1/30 Fix, 3/100 Fix, 3/120 Fix, 2/100 Fix, 2/120 Fix, 1/100 Fix, 1/120 Fix, 1/250 Fix, 1/500 Fix, 1/1000 Fix,
1/2000 Fix, 1/4000 Fix, 1/10000 Fix
•
Default: Outdoor scene
Note
•
When a faster shutter speed is selected (up to 1/10000), it is possible to capture a fast moving object
with less blur.
•
When a faster shutter speed is selected, the sensitivity will become lower. Smear also may appear
under bright light condition.
•
When "On" is selected for "Wide dynamic range", "Fix shutter" is not available. To configure "Fix
shutter", set "Wide dynamic range" to "Off".
[Light control mode]
Select the light control mode from the following.
•
Indoor scene (50 Hz) / Indoor scene (60 Hz): The shutter speed will automatically be adjusted to prevent
flicker caused by fluorescent light. Select 50 Hz or 60 Hz corresponding to the location where the camera
is in use.
•
ELC(Maximum exposure time): The lighting control will be automatically performed by adjusting shutter
speed in the range of ELC.
ELC(1/30s)/ ELC(3/100s)/ ELC(3/120s)/ ELC(2/100s)/ ELC(2/120s)/ ELC(1/100s)/ ELC(1/120s)/
ELC(1/250s)/ ELC(1/500s)/ ELC(1/1000s)/ ELC(1/2000s)/ ELC(1/4000s)/ ELC(1/10000s)
•
Default: ELC(1/30s)
Note
•
The shorter the maximum exposure time is, the more accurately it is possible to capture a fast moving
object with less blur.
•
When a faster shutter speed is selected, the sensitivity will become lower.
•
When a faster shutter speed is selected, flickering may happen.
In case flickering happens, it may be improved by configuring the following settings.
In the area of 50 Hz power supply frequency: ELC(3/100s), ELC(2/100s), ELC(1/100s)
In the area of 60 Hz power supply frequency: ELC(3/120s), ELC(2/120s), ELC(1/120s)
When flickering still remains, set flicker-less mode.
•
Under extremely strong lighting, flickering may happen even when "Indoor scene" is selected for "Light
control mode".
When the brightness (illuminance) level on the screen is set to a relatively low level with the [Brightness]
buttons, flickering may frequently happen.
108 Operating Instructions
SC384 SC384
SW175 SW175 SW174W SW174W SW172 SW172 ST165 ST165 ST162 ST162