Philips 4010W Series Service Manual page 34

EN 34 6. TPM15.3HE LA
Picture mode Screen size
Cool (11000K) 19HFL4010W/12
24HFL3010T/12
24HFL3010W/12
28HFL3010T/12
28HFL5010T/12
32HFL3010T/12
32HFL3010W/12
32HFL5010T/12
32HFL5010T/60
32HFL5110K/12
40HFL3010T/12
40HFL5010T/12
40HFL5010T/60
48HFL5010T/12
55HFL5010T/12
Warm (6500K) 19HFL4010W/12
24HFL3010T/12
24HFL3010W/12
28HFL3010T/12
28HFL5010T/12
32HFL3010T/12
32HFL3010W/12
32HFL5010T/12
32HFL5010T/60
32HFL5110K/12
40HFL3010T/12
40HFL5010T/12
40HFL5010T/60
48HFL5010T/12
55HFL5010T/12
This group setting of colour temperature will be applied
automatically to the TV / VGA / HDMI / AV / YPbPr sources.
6.4 Option Settings
6.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
MT5580 ICs is made known by the option codes.
Notes:
• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE and press OK on the RC.
• The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
6.4.2 Option Code Overview
Enter SAM mode to check the option codes. they could be
edited in the NVM.
6.4.3 Display Code Overview
Press the following key sequence on a standard RC
transmitter: "062598" directly followed by MENU and "xxx",
where "xxx" is a 3 digit decimal value of the panel type: see
column "Display Code" in
the Display Code, restart the set immediately.
2015-Otc-09
Alignments
Colour temperature
Red Green Blue
193 223 255
139 201 255
220 255 255
235 255 250
252 213 208
255 224 199
253 226 196
255 255 253
254 253 252
250 243 249
231 253 255
253 255 253
255 245 251
242 237 255
254 195 248
254 255 252
231 255 233
255 212 135
255 252 155
255 253 193
255 178 75
253 198 95
255 223 123
250 228 145
250 220 122
255 250 171
255 227 138
254 229 158
255 219 155
255 155 132
back to div.table 6-3. After resetting
Table 6-3 Display code overview
CTN_ALT BOM#
19HFL4010W/12
24HFL3010T/12
24HFL3010W/12
28HFL3010T/12
28HFL5010T/12
32HFL3010T/12
32HFL3010W/12
32HFL5010T/12
32HFL5010T/60
32HFL5110K/12
40HFL3010T/12
40HFL5010T/12
40HFL5010T/60
48HFL5010T/12
48HFL5010T/12
55HFL5010T/12
55HFL5010T/12
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool or use the "NVM editor" and "Dealer options"
items in SAM (do not forget to "store").
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM. The loading of the
CTN and production code can also be done via ComPair
(Model number programming).
2
C
In case of a display replacement, reset the "Operation hours
display" to "0", or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
6.5.1 Reset of Repaired SSB
Instruction
After NVM replacement, reload MAC address via SAM
menu.This ensures the correct MAC address to be available in
CSM for future repair actions.
Way of working:
• After the NVM has been replaced, go to SAM and scroll to
the <Reload MAC address> .
• Select the item and press <OK> on the RC.
Notes:
• Only applicable to all related models that are "Smart TV
level 0"enabled (only YouTube access). For models
without internet connection feature, no action is needed.
• HDCP keys are located in the NVM. If you are loading NVM
with the ComPair tool, there is warning message displayed.
New NVM EEPROMs are shipped with pre-loaded HDCP keys.
6.5.2 SSB Identification
SSB's of this chassis are identified by a "715" code on the SSB.
715Axxxx-Nnn-MMM-OOOO
back to
div.table
Panel Type Display Code
M185XTN01.200 SH AUO 226
TPM236H3-BJ1L01.N 131
TPM236H3-BJ1L01.N 131
TPT275B5-A014 S11C 105
TPT275B5-A014 S11C 105
TPT315B5-DXJSFE SE1E 141
TPT315B5-DXJSFE SE1B 112
TPT315B5-EUJFFE S1F 137
TPT315B5-EUJFFE S1F 137
TPT315B5-EUJFFE S1F 137
TPT400LA-J6PE1 SC1X 142
TPT400LA-J6PE1 SC1Z 138
TPT400LA-J6PE1 SC1Z 138
TPT480H2-HWU23.K S48P0B 139
TPT480LS-HN08.S SG01B 150
TPT550J1-DUYSHA.G S1D 140
TPT550J1-DUYSHA.G S1A 149