Figures - ABB HT574400 Operation Manual

Operation Manual / 4 Product description / A100-M axial

Figures

Figures
Fig. 1 Layout and function ...................
Fig. 2 Connection of the compressor
wheel cooling ............................
Fig. 3 Warning plates on the turbo-
charger......................................
Fig. 4 Locations of the rating plates ....
Fig. 5 Turbocharger suspension points
Fig. 6 Turbocharger suspension points
Fig. 7 Removing the foot mounting .....
Fig. 8 Loosening the clamping nut ......
Fig. 9 Turbocharger suspension points
Fig. 10 Removing auxiliary screw..........
Fig. 11 Compressor-end foot ................
Fig. 12 Turbine-end foot ........................
Fig. 13 CE foot contact surface .............
Fig. 14 TE foot: Handling of cup spring
contact surface / foot contact
surface ......................................
Fig. 15 Tightening the foot bolts (1) .......
Fig. 16 Tightening the clamping nut (2) .
Fig. 17 Lubricating oil pressure measur-
ing point ....................................
Fig. 18 Speed measurement .................
Fig. 19 Noise insulation, bellows ...........
Fig. 20 Cleaning the filter silencer (1) ....
Fig. 21 Cleaning the filter silencer (2) ....
Fig. 22 Cleaning the slotted diffuser ......
Fig. 23 Turbine and nozzle ring clean-
ing cycle ....................................
Fig. 24 Procedure Wet cleaning of tur-
bine and nozzle ring ..................
Fig. 25 Assemblies ...............................
Fig. 26 Removing / installing the filter
silencer .....................................
Fig. 27 Removing / installing the air
suction branch ...........................
Fig. 28 Axial clearance ..........................
Fig. 29 Removing wall insert .................
Fig. 30 Transporting and turning wall
insert .........................................
© Copyright 2016 ABB. All rights reserved.
4 Fig. 31 Removing the diffuser ............... 65
Fig. 32 Remove compressor casing ...... 66
5
Fig. 33 Safety-relevant screws .............. 67
Fig. 34 Removing cartridge group 1 ...... 68
6
Fig. 35 Removing cartridge group 2 ...... 69
7
Fig. 36 Removing turbine diffuser 1 ...... 70
9
Fig. 37 Removing turbine diffuser 2 ...... 70
10
Fig. 38 Removing cover ring 1 .............. 71
11
Fig. 39 Removing cover ring 2 .............. 71
12
Fig. 40 Removing nozzle ring 1 ............. 72
13
Fig. 41 Removing nozzle ring 2 ............. 72
14
Fig. 42 Installing nozzle ring 1 ............... 73
15
Fig. 43 Installing nozzle ring 2 ............... 74
15
Fig. 44 Installing cover ring ................... 75
16
Fig. 45 Installing turbine diffuser 1 ........ 76
Fig. 46 Installing turbine diffuser 2 ........ 76
16
Fig. 47 Installing the cartridge group 1 .. 77
17
Fig. 48 Installing the cartridge group 2 .. 78
18
Fig. 49 Installing the compressor casing
Fig. 50 Installing diffuser ....................... 81
23
Fig. 51 Turning and moving in wall insert
25
Fig. 52 Fitting the wall insert ................. 83
30
Fig. 53 Axial clearance .......................... 84
38
Fig. 54 Removing the nozzle ring at the
40
turbine end ................................ 86
41
Fig. 55 Installing the nozzle ring at the
turbine end ................................ 87
48
Fig. 56 Tightening torques 1 ................. 90
Fig. 57 Tightening torques 2 ................. 90
48
Fig. 58 Flange tightening sequence ...... 92
59
Fig. 59 Fitting the locking device ........... 95
Fig. 60 Cover plate dimensions ............. 97
60
Fig. 61 Fitting the cover plate ................ 98
Fig. 62 Turbocharger with part numbers 108
61
62
63
64
HZTL4033_EN
Page 111 / 113
Revision A July 2016
80
82