● “Important Information” (P. EN2 - EN4). Please keep this Operating Instructions for future use. ● Panasonic will not accept any liability if the appliance is subject to improper use, failure to comply with ● these instructions. Contents Safety Precautions ..........................EN2 Important Information .........................
Page 4
There is abnormal turning noise while in use. ● There is another abnormality or failure. ● Contact Panasonic Service Centre for inspection or repair. ➜ Make sure the voltage indicated on the label of the appliance is the same as your local supply. ●...
Do not blend or place over 60 °C ingredients into the blender jug. ● Do not put any liquids or wet ingredients into mill container. (MX-EX1011, MX-EX1031 only) ● Do not open the lid and put your fingers or utensils such as spoon or fork into the blender ●...
Parts Names and Instructions Blender Dry mill Accessory (MX-EX1011, MX-EX1031 only) MX-EX1001 / MX-EX1011:1 set MX -EX1031: 2 sets Mill container Scraper ● During blending, use the scraper only through lid Blender jug opening. Do not use with Mill gasket lid off.
How to Use Blender Dry mill (MX-EX1011, MX-EX1031 only) To disassemble To assemble Place the ingredients into blender jug, and then close the lid. Turn anticlockwise Turn clockwise ● Pour liquid first, followed by soft ingredients and then others. (i) Liquid (ii) Soft ingredients (iii) Hard ingredients (iv) Ice cubes...
Turn the rotary switch to "0" position, unplug and rest the appliance for about 15 minutes or more (until motor housing returns to a normal temperature) to release overheating protection before using again. (If appliance still does not operate, contact Panasonic Service Centre for inspection or repair.) VZ50V324_MX-EX1001_MX-EX1011_EX1031 (EN+VN+TH).indd 7 VZ50V324_MX-EX1001_MX-EX1011_EX1031 (EN+VN+TH).indd 7...
Even turn to "1" it firmly until you hear a "click" sound. position, the ● The mill container base is not assembled tightly. (MX-EX1011, MX-EX1031 only) ➝ Assemble it tightly. (P. EN6) appliance ● The protection device of overload or overheating is activated.
Page 10
Hãy giữ tờ Hướng dẫn Sử dụng này để sử dụng trong tương lai. ● Panasonic sẽ không chịu bất kỳ trách nhiệm pháp lý nào nếu thiết bị được sử dụng không đúng cách, ● không tuân thủ các hướng dẫn này.
Page 11
Do các hỏng hóc và hiện tượng bất thường khác. ● Hãy liên hệ Trung tâm Bảo hành Panasonic để được kiểm tra hoặc sửa chữa. ➜ Đảm bảo điện áp ghi trên nhãn của sản phẩm phù hợp với điện mức trong khu vực.
Lưu ý an toàn Xin vui lòng làm theo những hướng dẫn sau. THẬN TRỌNG Không trộn hoặc bỏ các nguyên liệu trên 60 °C vào trong cối xay. ● Không cho bất kỳ chất lỏng nào hoặc nguyên liệu ướt vào cối xay khô. ●...
Cách sử dụng Máy xay sinh tố Máy xay khô (MX - EX1011, MX - EX1031 chỉ) Tháo rời Lắp ráp Cho các nguyên liệu vào trong cối xay, và sau đó đóng nắp. Xoay ngược chiều kim đồng hồ Xoay theo chiều kim đồng hồ...
Vặn công tắc về vị trí "0", rút phích cắm và để thiết bị nghi ̉ trong khoảng 15 phút hoặc lâu hơn (cho đến khi vỏ động cơ trở về nhiệt độ bình thường) để ngắt bảo vệ quá nhiệt trước khi sử dụng lại. (Nếu thiết bị vẫn không hoạt động, hãy liên hệ với Trung tâm Bảo hành Panasonic để kiểm tra hoặc sửa chữa.) VN.indd 7 VN.indd 7...
➝ Hãy lấy chúng ra. ● Gioăng cối xay khô bị hỏng. ➝ Hãy liên hệ với Trung tâm Bảo hành Panasonic để thay thế. ● Lượng chất lỏng không đủ. ➝ Hãy cho thêm chất lỏng. Lưỡi dao không ●...