Huawei HoloSens Quick Start Manual page 2

Port Description/ 接口说明
1
2
3
4
5
6
NO. Item Description
序号 名称 说明
Power input port.
1 POWER
电源输入接口。
Network port.
2 LAN
网络接口。
Ground port of a camera.
3 GND
设备接地接口。
RS485 port. This port provides a transparent data channel used for half-duplex transmission
RS485_A/
4 between the camera and the connected device.
RS485_B
RS485接口。通过该接口，摄像机可以以半双工的方式通过透明通道与连接的设备互相传递数据。
AUDIO IN/
Audio input/output port and audio ground port.
5 AUDIO OUT/
AUDIO IN/AUDIO OUT为音频输入/输出接口。AUDIO_GND为音频接地接口。
AUDIO_GND
Alarm output and reference ports. A pair of ALARM_OUT and ALARM_REF forms a single
alarm out. The rated voltage of the alarm output device is less than or equal to or equal to 30
ALARM_
V DC or 125 V AC, and the rated current is less thanc to 200mA.
OUT/
告警输出接口。ALARM OUT和ALARM REF组成一组告警输出。告警输出所驱动设备的额定电压不高于
ALARM_REF
DC 30V或AC 125V，且额定电流均不大于200mA。
Alarm input ground port.
ALARM_GND
告警输入接地接口。
6
Alarm input port. There may be multiple alarm input ports. For a given number of
ports, n, they are numbered (for example: ALARM_IN0, ALARM_IN1, ..., ALARM_INn). Each
one connects to the ALARM_GND connection to form a single alarm input.
ALARM_IN 告警输入接口。存在多个告警输入线，则采用ALARM_INn表示，n为数字，每条告警线与ALARM_GND
组成一
组告警输入。
Required Tools/ 准备安装工具
Wiring terminals Waterproofing tape&PVC insulation tape
接线端子 防水胶带&绝缘胶带
Marker 10 mm hammer drill (for wall-mounted
记号笔
冲击钻,Φ10mm（墙壁安装时使用）
NOTE/ 说明
• The appearance and components vary depending
on camera models. The figures in this document
are for reference only.
不同款型设备的外观、结构存在差异，本文档示意图
仅供参考，请以实物为准。
• You can log in to http://holosens.e.huawei.com,
search for the desire device model, and view the
datasheet to obtain the device specifications.
您可以登录 http://holosens.e.huawei.com，搜索
对应款型，查看相应的彩页，获取设备详细技术参数。
Measuring tape
钢卷尺
installation) Hammer (for wall-mounted installation)
羊角锤（墙壁安装时使用）
Reset Button and SD Card Slot/ Reset 键和 SD 卡槽
3
NO. Description
序号 说明
Off: The device is not powered on.
灯灭：设备未上电。
Orange: The systerm is starting.
橙色：系统正在启动。
Steady green: The device is running properly.
绿色长亮：设备正常。
System running
status indicator Steady red: The hardware is faulty.
1
系 统 运 行 状 态 指 红色长亮：硬件产生故障。
示灯
Fast flashing red: The device temperature is outside of its acceptable operating range and an
alarm has been generated.
红色快闪：高温低温到达阈值，产生温度告警。
Blinking red continuously: An exception occurs on the external network port.
红色持续闪烁：设备对外网口异常
Blinking red twice in 5s: An exception occurs on the rotatable lens.
5秒内红色闪烁2次：动点异常
This device supports class 10 or higher Micro SD card. You must power of the device to
replace a Micro SD card. Otherwise, system exceptions may occur. When a Micro SD card is
SD card slot used for the first time, log in to the web client of the device and format the Micro SD card.
2
SD卡卡槽 For details, see the Configuration Guide.
支持Micro SD卡（Class 10及以上）。请在设备断电的情况下插拔SD卡，否则会造成系统异常。首次
使用，请登录设备Web客户端，格式化SD卡，操作方法请参见《配置指南》。
To restart the device, hold down the reset button (less than 3s). To restore the device to
factory settings, hold down the reset button for at least 5s while the device is running.
Reset button Restoring the factory configuration will result in the loss of the user's account information
3
重置按钮 and some of the configuration information. Please exercise caution.
运行时按住RESET键短于3秒重启设备;运行时按住RESET键不短于5秒后恢复出厂配置。 恢复出厂配置将
会导致用户的账号信息以及部分配置信息丢失，请慎重操作。
M8 socket wrench
套筒扳手（M8）
#2 Phillips screwdriver
十字螺丝刀（2#）
2
1 2
NOTE/ 说明
Use the Phillips screwdriver to remove the
camera bottom cover. Then, you can see the
indicators, SD card slot, and reset button.
使用十字螺丝刀将设备窗口盖卸下，即可看到指示
灯、SD卡卡槽和重置按钮。
Wire stripper RJ-45 connector crimping tool
剥线钳 水晶头压线钳
Diagonal cutting pliers
Adjustable wrench
斜口钳
活动扳手