Philips 43PUH6101/88 Service Manual page 23

• 1.4b Option Code 2 Gives the option codes of option
group 2 as set in SAM.
• 1.5 SSB Gives an identification of the SSB as stored in
NVM. Note that if an NVM is replaced or is initialized after
corruption, this identification number has to be re-written to
NVM. This identification number is the 12NC number of the
SSB.
• 1.6 Display 18NC NVM read/write.
• 1.7 PSU 18AC NVM read/write.
• 1.8 RF4CE 18AC NVM read/write.
• 2.1 Current Main Software Displays the built-in main
software version. In case of field problems related to
software, software can be upgraded. As this software is
consumer upgradeable, it will also be published on the
internet.
• 2.2 Standby SW Displays the built-in stand-by processor
software version. Upgrading this software will be possible
via USB.
• 2.3 Panel Code Displays the Display Code number.
• 2.4 Bootloader ID ID of Bootloader.
• 2.5 NVM version Detects and displays NVM version.
• 2.6 Flash ID ID of flash model.
• 2.7 e-UM version eDFU (help) version.
• 2.8 Channel Table Structure Version version of channel
table structure.
• 2.9 Error Codes Detects and displays errors.
• 3.1 Signal Quality Analog/digital signal strength.
5.2 Stepwise Start-up
Standby Soft Mode
Command Received,
previously in Standby
Soft Mode (Power tact
switch)
TV Wakeup
commands
Received
(TV Wakeup
keys)
Power On
Service Modes, Error Codes, and Fault Finding
Digital
background
tasks started
Standby
commands
Received (RC
Standby key)
Standby Soft Mode
Command Received,
previously in Standby
Soft Mode (Power
TV Wakeup
tact switch)
commands
Received
(TV Wakeup
keys)
Switch On, previously
in Power On Mode
(Power tact switch)
Standby Soft Mode
Command Received,
(Power tact switch)
Figure 5-1 Stepwise Start-up
• 3.2 Child lock Not active / active. This is a combined item
for locks. If any lock (channel lock, parental lock) is active,it
is indicated as "active".
• 3.3 HDCP keys Indicates the validity of the HDMI keys (or
HDCP keys). In case these keys are not valid and the
customer wants to make use of the HDMI functionality, the
SSB has to be replaced.
• 3.4 Ethernet MAC address A Media Access Control
address (MAC address) is a unique identifier assigned to
network interfaces for communications on the physical
network segment.
• 3.5 Wireless MAC address Wireless Media Access
Control address.
• 3.6 BDS key Indicates the validity of the BDS key. In case
this key are not valid and the customer wants to make use
of the functionality, the SSB has to be replaced.
How to Navigate
By means of the "CURSOR-DOWN/UP" knob (or the scroll
wheel) on the RC-transmitter, can be navigated through the
menus.
How to Exit CSM
To exit CSM, use one of the following methods.
• Press the MENU/HOME button on the remote control
transmitter.
• Press the POWER button on the remote control
transmitter.
• Press the POWER button on the television set.
Standby
Digital
background
tasks completed
Swith On,
Semi-
previously in
Standby
Standby/Semi-
Standby (Mains
Power Plug)
Standby
Soft Mode
Command
Switch Off (Mains
Received
Power Plug)
(Power tact
switch)
Standby
Swith On,
Soft Mode
previously in
Standby Soft Mode
(Mains Power Plug)
Switch Off (Mains
Power Plug)
back to
div.table
TPL16.1E LA 5.
Switch
Off(Mains
Power Plug)
Switch Off
(Mains Power
Plug)
Power Off
Switch On,previously in
TV Operation Mode
(Mains Power Plug)
EN 23
19080_206_110323.eps
120224
2016-Sep-23