Related Manuals for Toro 03713
Summary of Contents for Toro 03713
- Page 1 Form No. 3392-136 Rev A Right/Left-Hand Groomer Kit 27-inch Reelmaster ® 7000-D DPA Cutting Unit Model No. 03713 Model No. 03714 *3392-136* A Register at www.Toro.com. Original Instructions (EN)
- Page 2 You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.
-
Page 3: Table Of Contents
Authorized Toro Distributor. • To ensure optimum performance and safety, always purchase genuine Toro replacement parts and accessories to keep the Toro all Toro. Never use “will-fit” replacement parts and accessories made by other manufacturers. Look for the Toro logo to assure... - Page 4 Using unapproved replacement parts and accessories could void the warranty of The Toro® Company.
-
Page 5: Setup
Torque wrench 27-33 ft-lb (36-45 N-m) • Torque wrench 34-40 ft-lb (46-54 N-m) The Right and Left Groomer Kit Models 03713 and 03714 can be used on Reelmaster 7000-D DPA Cutting Unit Models • Torque wrench 85-95 ft-lb (115-129 N-m) 03710 and 03711 with or without a Rear Roller Brush Kit. -
Page 6: Installing The Groomer
Groomer Kit Orientation All cutting units are shipped with the counter weight mounted to the left end of the cutting unit. Use the following diagram to determine the position of the groomer kits and reel motors. Figure 2 Figure 3 1. - Page 7 Note: The washers on the height of cut adjusting splined insert, on the right hand side of the cutting bolts must be located on each side of the flange on the unit, has right hand threads. side plate (Figure 13. Install the new (longer) splined insert to the reel shaft (Figure 7).
- Page 8 Important: Make sure the pivot hub mounting 18. Secure the non-drive pivot hub to the cutting unit side surface is flush with the side plate on the cutting plate with (2) 3/8 x 1 inch socket head screws (Figure unit. The shim must not be pinched between the 9).
- Page 9 • 20. Mount the quick-up lever assemblies to the side plates The outer faces of the drive and driven pulleys with 3/8 x 3/4 inch flange head bolts (Figure should be in line within .030 inch (.76 mm). • If the pulleys are not aligned, refer to the section 21.
- Page 10 Note: After greasing groomer bearings, operate idler pulley to the roller brush pivot plate. Do not groomer for 30 seconds, stop machine and wipe excess remove the nut. grease from groomer shaft and seals. 5. Remove the bolt securing the roller brush drive pulley 27.
- Page 11 Figure 20 Figure 18 1. Height of cut bracket 3. Carriage bolt 1. Bearing housing 2. Capscrew & locknut 12. Remove the carriage bolts and nuts securing the height 16. Using the upper square hole in each side plate, loosely of cut brackets to the cutting unit side plates (Figure mount the height of cut brackets to the cutting unit...
- Page 12 Clean all the grease out of the threaded hole where the splined insert was. Important: The splined insert on the left hand side of the cutting unit has left hand threads. The splined insert, on the right hand side of the cutting unit, has right hand threads.
- Page 13 Figure 24 1. Groomer shaft assembly 7. Shim (must remain loose after installation) 2. Groomer plate w/quick-up lever (non-drive end) 8. Pivot hub (non-drive end) 3. Pivot hub (drive end) 9. Idler spring 4. Splined shaft 10. Belt 5. Groomer plate w/quick-up lever (drive end) 11.
- Page 14 31. Remove the (2) 5/16 inch flange nuts securing the groomer weight to the groomer cover and remove the weight (Figure 28). Figure 26 Figure 28 1. Idler spring 3. Lower stud 2. Idler plate tab 1. Groomer weight 4. Rubber grommet ring 2.
- Page 15 36. Apply a film of grease to the inside diameter of the the pulley tabs are positioned in the slot in the drive grommet in the groomer cover (Figure 29). shaft. 44. Apply Loctite to the threads of the 3/8 x 2 inch flange 37.
- Page 16 46. Push down on the idler pulley to ensure that the idler pulley assembly pivots freely. 47. Check the alignment of the belt/pulleys as follows: • Lay a straight edge along the outer face of the drive pulley (Figure 33). G011429 Figure 35 G011428...
-
Page 17: Installing The Broomer Kit (Optional)
Installing the Broomer Kit (optional) 1. From one side of the groomer reel, slide a brush into each groove around the full length of the groomer reel (Figure 36). Figure 36 1. Brush 2. Strap 2. Verify that the brushes are seated in the groomer blade slots (Figure 37 &... -
Page 18: Operation
Operation • The height/depth setting on the grooming reel • How long the grooming reel has been in use Grooming is performed in the turf canopy above the soil • The type of grass level. Grooming promotes vertical growth of grass plants, •... - Page 19 Figure 40 1. Quick-up lever (engaged 3. Height adjuster knob position) 2. Groomer height (HOG) 4. Number of rear roller spacers (below side plate pad) 5. Repeat step on the opposite end of the groomer. Then, recheck the setting on the first side of groomer. Height setting on both ends of the groomer should be identical.
-
Page 20: Testing The Groomer Performance
Height of Cut (HOC) and Height of Groom (HOG) Recommended Range Height of Cut Number of Rear Roller Recommended HOG = HOC- Groomer Engagement Spacers .250 inch (6.4 mm) .125-.250 (3.1–6.4 mm) .375 inch (9.5 mm) .187-.375 (4.7–9.5 mm) .375 inch (9.5 mm) .187-.375 (4.7–9.5 mm) .500 inch (12.7 mm) .250-.500 (6.4–12.7 mm) -
Page 21: Maintenance
Maintenance 2. Remove idler spring, releasing tension from the belt. Remove the belt. 3. Remove the lock nut securing the driven pulley to the Cleaning end of the groomer shaft. Insert a 5/8 inch wrench on the flats on the groomer shaft to keep the shaft from Hose off the grooming reel after using it. -
Page 22: Groomer Binding Troubleshooting
Groomer Binding 5. If a roller brush is installed, make sure the brush plate (Figure 46) is parallel to the cutting unit side plate and Troubleshooting is fully inserted into the rubber grommets. 1. Make sure the groomer is set to the desired height of groom (HOG) (Figure 44). - Page 23 Figure 48 1. Shim 8. Make sure nuts on groomer and roller brush covers (Figure 49) are not over tightened. Figure 49 1. Cover...
- Page 24 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.