Table of Contents
Advertisement
Available languages
Available languages
Warranty is responsible only for material faults or
manufacturing faults, electric parts are not included.
Warranty is not responsible in case of improper use or
Most of the inconveniences are due to lack of maintenance; undertake maintenance operations regularly (by operator or
by qualified personnel), see "Maintenance". Here below is a list of inconveniences (with causes and possible solutions)
solvable without the intervention of qualified personnel of the service centre. Before proceeding with the
inconvenience resolution operations, read carefully the "Safety warnings".
Inconvenience
The machine doesn't work:
1.
.the general switch of the machine
is ON and the red light "POWER"
is OFF
.the touch screen is OFF
The machine doesn't work:
2.
.
the
general
switch
machine is ON and the red light
"POWER" is OFF
. the touch screen is ON
3.
There is no steam and the
machine is switched on but cold.
4.
Water mixed with steam comes
out at the beginning of work.
5.
Water mixed with steam comes
out even after the first working
cycles.
6.
Blowing
capacity
reduced.
7.
One
pneumatic
device
.
moving
8.
Abnormality in the handling of
pneumatic devices.
9.
Alarm: Input 00
Emergency button pressed.
The machine stopped and turned
the red light "POWER" is
off
(
OFF
.
)
10. Alarm: Input 02
Right sensor
not active.
The machine does not start.
11. Alarm: Input 03
Left sensor
not active.
The machine stopped.
12. Alarm: Input 05
Air pressure
The machine stopped.
the red light "POWER" is
OFF (
OFF
).
13. Alarm: Input 06
Press in not-open position.
The machine stopped.
14. Alarm: Input 07
Press in not-closed position.
The machine stopped.
INCONVENIENCES
1a. The power supply line doesn't work.
1b.
The safety switch of the electrical
panel isn't locked.
2.
Procedure of powering up not
completed.
of
the
3.
Steam does not get to the machine.
4.
The machine is cold.
5.
Troubles
steam/return outlet.
has
been
6.
The fan filter is dirty.
PNEUMATIC DEVICES
7.
Compressed air does not get to the
is
not
machine.
8.
There are some obstacles.
9.
The red mushroom Emergency-
Stop has been pushed (deliberately
or accidentally).
10. There are some obstacles.
11. There are some obstacles.
12. The compressed air pressure at inlet
is <5 bar.
and turned
13. There are some obstacles.
14. There are some obstacles.
mishandling, use of strength or operations carried out by
non-authorized personnel (see "Safety warnings").
Cause
POWERING UP
STEAMING
on
the
inlet
line
BLOWING
PLC ALARMS
- 15 -
Solution
1a. Check that the general electrical
supply switch on the electrical line
is ON and that there is power in
the electric power line.
1b.
Check that the door of the electrical
panel is properly closed.
2.
Press
the
RESET
restore the functionality of the
machine.
3.
Check that the steam tap is open,
the steam generator works.
4.
Wait a few minutes to allow the
machine to warm up.
5.
Check that the steam generator
works properly.
6.
Proceed
with
cleaning
"Maintenance").
7.
Make
sure
that
compressed
air
properly connected.
8.
Remove
obstacles
"Maintenance").
Reset the machine (see "Use-
9.
Emergency-Stop
and
buttons").
10. See Inconvenience n°8.
11. See Inconvenience n°8.
12. Press
the
red
EMERGENCY-STOP and
that the compressed air tap is
open, the compressor regularly
works and the pressure level
corresponds
to
the
working pressure (see "Technical
section"/CE
label).
machine (see "Use-Emergency-
Stop and Reset buttons").
13. See Inconvenience n°8.
14. See Inconvenience n°8.
button
to
(see
the
related
pipes
are
(see
Reset
mushroom
heck
c
machine
Reset
the
Advertisement
Table of Contents
