Advertisement
Quick Links
Rear Roller Brush MVP Kit
Reelmaster
5-inch or 7-inch Reel
Model No. 133-0157
Model No. 133-0158
This product complies with all relevant European directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
No parts required
Roller-brush housing
Hex-socket bolt (3/8 x 1 inch)
Grease fitting (90°)
Shoulder bolt (flange hex socket)
Roller-brush assembly
Shoulder bolt
Belt cover/plate assembly
Bolt (5/16 x 1/2 inch)
Spacer
Drive pulley
Flange-head bolt (3/8 x 2 inches)
Belt
Shim washer (as required for belt alignment)
Driveshaft (right-hand threads)
Driveshaft (left-hand threads)
High height-of-cut brush (optional)
Important:
For a 5-inch cutting unit drive by an
electric reel motor, you must order 1 weight (Part
No. 127-4259-03) and 2 bolts (Part No. 322-7).
Note:
Determine the left and right sides of the cutting
unit from behind the cutting unit.
Important:
Use the Rear Roller Brush Kit only
when cutting in the height-of-cut range of 6 to
25 mm (1/4 to 1 inch). Use the high height-of-cut
brush when cutting above 25 mm (1 inch). Refer to
Installing the High Height-of-Cut Brush (page
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3555, 3575, 5010, and 5010-H Series Cutting Unit with
Qty.
–
Determine the roller brush orientation.
1
2
1
1
1
1
1
4
Install the roller brush.
1
1
1
1
1
1
1
Install the high height-of-cut brush—for HOC greater than
–
2.5 cm (1 inch).
8).
Register at www.Toro.com.
Form No. 3399-460 Rev C
Installation Instructions
Use
Original Instructions (EN)
All Rights Reserved *3399-460* C
Printed in the USA
Advertisement
Related Manuals for Toro 133-0157
Summary of Contents for Toro 133-0157
- Page 1 Reelmaster ® 3555, 3575, 5010, and 5010-H Series Cutting Unit with 5-inch or 7-inch Reel Model No. 133-0157 Model No. 133-0158 Installation Instructions This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
- Page 2 Determining the Roller Installing the Roller Brush Brush Orientation Installing the Driveshaft Refer to Figure 1 to determine the position of the roller Restrain the reel for removal; refer to Restraining brush and reel motors. the Reel for Removing Threaded Inserts (page 11).
- Page 3 Figure 4 1. Roller-brush housing 3. Hex-socket bolt 2. Threaded hole 4. Front of the machine For Model 133-0157 kit for Reelmaster 5010 machines with 5-inch cutting units only: • For a hydraulic-driver reel motor: Install g035933 Figure 6...
- Page 4 Installing the Roller Brush Assembly Remove the grease fitting for the roller from the side of the cutting unit that has the roller-brush housing (Figure g037641 Figure 9 g031872 Figure 7 1. Left roller-brush assembly 3. Washer (4) 2. Roller-brush mounting 4.
- Page 5 Installing the Roller Brush Plate Install the left or right roller-brush plate (Figure 11). Slide each excluder seal outward until the lip Note: When you insert the protrusion on seals are in light contact with each bearing the plate into the grommet in the roller-brush housing (Figure 10).
- Page 6 Important: Secure the brush plate to the roller-brush Heavy brush contact on the housing with the shoulder bolt (Figure 11). roller will cause premature brush wear. Note: Torque the bolt to 20 to 25 N∙m (15 to 19 ft-lb). Note: The shoulder bolt should not clamp the plate to the housing.
-
Page 7: Installing The Belt
Installing the Drive Pulley Insert the spacer onto the shaft in the bearing housing (Figure 15). g027196 Figure 16 1. Drive pulley 3. Belt 2. Idler-pulley assembly 4. Driven pulley g027195 Figure 15 • Start the belt on the driven pulley (Figure 17). -
Page 8: Completing The Installation
Installing the High Push down on the idler pulley to ensure that the idler-pulley assembly pivots freely. Height-of-Cut Brush Completing the Installation Optional Check the alignment of the belt and pulleys; Install the high height-of-cut brush (sold separately) refer to Checking the Pulley Alignment (page when the height of cut is 2.5 cm (1 inch) or more (5 or Slide the belt cover onto the mounting bolts and... -
Page 9: Maintenance
Maintenance Loosen the 2 bolts, washers, and nuts securing the drive-bearing housing to the bearing-housing mounting bracket (Figure 22). • Ensure that the brush is parallel to the roller with Slide the high height-of-cut brush onto the brush 1.5 mm (0.060 inch) clearance to light contact. shaft (Figure 22). - Page 10 Adjusting the Pulley Alignment The driven pulley (at the roller-brush shaft) can move in or out (Figure 24). Note: Make note of which way the pulley needs to move when checking the belt alignment; refer Checking the Pulley Alignment (page g009077 Figure 25 1.
- Page 11 Restraining the Reel WARNING The cutting reel blades are sharp and capable of amputating hands and feet. • Keep your hands and feet outside of the reel. • Ensure that the reel is restrained before servicing it. Restraining the Reel for Removing Threaded Inserts Loosen the shield-bolt on the left side of the cutting unit and raise the rear shield...
- Page 12 Restraining the Reel for Installing Threaded Inserts Insert a long-handled pry bar (recommended 3/8" x 12" with screwdriver handle) through the front of the cutting reel, closest to the side of the cutting unit that you will be torquing (Figure 29).
- Page 13 Notes:...
- Page 14 Notes:...
- Page 15 Notes:...
- Page 16 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.