Parameter List - Panasonic AJ-HDR150P Operating Instructions Manual

Display Panel

Parameter List

USER SET
Setting item Setting
Dropped Frame DF Selects the frame mode in use.
NDF
Protocol Odetics Selects the control protocol in use with
Louth RS-422A.
FF.REW Max x32, x64, Selects the speed for FF/REW.
x128
SDTI Slow Audio Valid Selects audio data output for playback
at a1 speed or below.
Invalid
Rec Start 00:00:00 Selects the recording starting point
Position 00:59:59 when recording instruction has been
01:00:00 given by operating the front panel
when creating a new CLIP.
Record Duration 10min Selects the recording time length of
15min CLIP ID used during loop recording (L-
30min REC).
45min <Note>
1H O Upon writing over the existing CLIP
2H ID, loop recording takes place within
4H the length of recording time set from
8H the current position.
O Loop recording operation takes
place only during STOP.
FTP Put Offset 00:00:00 Selects the recording starting point
00:59:59 when recording is done through
01:00:00 transmission from a non-linear system.
SDTI Illegal Input Rec Stop Selects operation when SDTI signal
Continue has detected no signal during
recording.
Ch1 Default Rate 25Mbps Selects the format of signals used in
50Mbps each channel.
100Mbps However, the upper limit of maximum
usable stream count (25 Mbps mode
Ch2 Default Rate 25Mbps
taken as 1) that has been set cannot
50Mbps
be exceeded.
100Mbps
For details, consult your dealer.
Ch3 Default Rate 25Mbps
50Mbps
100Mbps
Ch4 Default Rate 25Mbps
50Mbps
100Mbps
Ch1 Default x1, x2, x4
Times
Ch2 Default x1, x2, x4
Times
Ch3 Default x1, x2, x4
Times
Ch4 Default x1, x2, x4
Times
indicates factory setting mode.
A/S SET
Remarks Setting item
CH1 CF Enable
CH1 VOUT
SetUp
CH1 VIN SetUp
CH1 SYS H
CH1 SYS SC
CH1 SCH
CH2 CF Enable
CH2 VOUT
SetUp
CH2 VIN SetUp
CH2 SYSH
CH2 SYS SC
CH2 SCH
CH3 CF Enable
CH3 VOUT
SetUp
CH3 VIN SetUp
CH3 SYSH
CH3 SYS SC
CH3 SCH
CH4 CF Enable
CH4 VOUT
SetUp
CH4 VIN SetUp
CH4 SYSH
CH4 SYS SC
CH4 SCH
23
Setting Remarks
On Selects channel 1 color frame control.
Off
Add Selects setup level during channel 1
Thru playback.
Cut Selects setup level during channel 1
Thru recording.
Performs rough tuning of channel 1
–121
0 +120 system phase in relation to standard
signal. (37ns step)
Performs fine tuning of channel 1
0 1023
system phase in relation to standard
signal. (0.35° step)
Performs tuning of channel 1 SC-H
–128
0 +127 (Subcarrier to Horizontal) phase.
(1.41° step)
On
Off
Add
Thru
Cut
Thru
Channel 2 setting is the same as for
channel 1.
–121 0
+120
0 1023
–128 0
+127
On
Off
Add
Thru
Cut
Thru
Channel 3 setting is the same as for
channel 1.
–121 0
+120
0 1023
–128 0
+127
On
Off
Add
Thru
Cut
Thru
Channel 4 setting is the same as for
channel 1.
–121 0
+120
0 1023
–128 0
+127