Husqvarna AUTOMOWER 420 Operator's Manual page 30

3. Use the number buttons to set the distance.
4. Push the BACK button.
4.2.9 Settings
In settings you can change the general settings to your
product.
4.2.9.1 Profiles
With the function Profiles, different sets of product
settings can be saved. This can be used when one
product is used for more than one work areas and
charging stations. The product settings and the pairing
with the charging stations are saved in the profile and
can easily be used again.
To save settings to a profile
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Use profiles > Profile A, B, C.
3. Use the arrow buttons and the OK button to select
and save the profile.
4. Push the BACK button.
If settings have been changed but not saved, the symbol
* is shown beside the profile name.
To change the name of a profile
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure Settings
Use profiles > Profile A, B, C. > Rename.
3. Use the arrow buttons and the OK button to select
letters.
4. Push the BACK button to save the new profile
name.
To use a profile
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Use profiles > Profile A, B, C > Select.
3. Push the BACK button.
To connect a new charging station to a profile
1. Save the settings in a profile to be used with the
original charging station. Do steps 1–4 in
settings to a profile on page 30 .
2. Put the product in the new charging station.
30 - Product settings
Settings > Profiles >
> Profiles >
Settings > Profiles >
To save
3. Use the arrow buttons and the OK button to move
through the menu structure
New loop signal .
4. Save a profile for the new charging station, or
select a profile in the list. Do steps 1–4 in
settings to a profile on page 30 , or do steps 1–3 in
To use a profile on page 30 .
4.2.9.2 ECO mode
ECO mode disables the signal in the boundary wire,
guide wire and the charging station, when the product is
parked or is charging.
Note:
ECO mode to save energy and to prevent
Use
interference with other equipment, for example hearing
loops or garage doors.
Note:
To start the product manually in the work area,
push the STOP button before you remove the product
from the charging station. If not, the product cannot be
started in the work area.
To set the ECO mode
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to move
through the menu structure
3. Push the OK button to select the
4. Push the BACK button.
4.2.9.3 Spiral Cutting
The product cuts the grass in a spiral pattern if the grass
Spiral cutting can be set in 5 levels:
is longer in an area.
• Low-
• Low
• Mid
• High
• High+
The level sets how sensitive the product is to changes in
grass height.
Note:
Spiral cutting is only started in the Main area
Secondary area mode does not let
mode. Cutting in the
Spiral cutting . Spiral Cutting does not
the product to start
start in slopes steeper than 15%.
To set the Spiral Cutting
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to
move through the menu structure
Cutting > Use Spiral Cutting .
3. Push the BACK button.
Security > Advanced >
To save
Settings > ECO mode .
ECO mode .
Settings > Spiral
1201 - 007 - 20.02.2023