Kenwood 107VR Instruction Manual page 5

107VR (En]
system control operations.
XS8 Mode: tets you combine KU XS, and XS8 terminals
GLIB) Mode: for GLI) terminals only
This unit is compatible with both [XS8] and [SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8]
mode, foilow the instructions in "SWITCHING BETWEEN [XS8] AND [SL16]" below.
EXAMPLE: [XS8} mode connections
The underlined portion represents the setting of the system
contro!l mode.
Turrtab € ;
Receiver
[$L16] [XS8]}
ya System
MD Recone: {SL16] eens contrat
cord
Muluple
CD Player
[SL16} [XS} [X$8]
Note
Saal
2)
cause a malfunction and damage your equipment
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system.
control mode.
>
'
Turntab-€
isin] X22
eed
System
[SL16]
MD Recorcer
pee
cord
LD Payer
Mauitiple
[SL16] [XS] [XS8} CD Player
e Some CD players acd cassette decks are not compatible with the [SL16] system contro! mode. Be sure to use the [XS8] system control made wnen
making system connectiors with equipment tnat is not [SL16} compatible.
eSome MD payers are rot system contro: compatible You canrat make system control connections to this kind of equipment.
3 Be sure tre system control plugs are 'nserted al! the way :n to the system control terminals
1 [S_16] equinr-ert cannot be combined witn [XR}, [XS], and [XS8] equipment for system operations. If your
ama eguioment consists of tis kira of combination, please do not connect any system contro! coras Even
without system control cords. normal operazicns can be carried out without affecting performance
2 Oconotconnect system contral cords to any components other than thase specified by KENWOOD. It may
die o Be ;
Remote Contro! (possible when the system control mode
matches)
Lets you operate source components with the system remote
supplied with this unit.
| ABOUT THE SYSTEM CONTROL OPERATIONS |
4
: Automatic Operation (Except [XR] equipment)
When you start playback from a source component, the input
selector on this unit switches to that component automatically.
(Except TAPE 2)
Synchronized Recording (Except [XR] equipment)
Lets you synchronize recording with the start of playback when
recording from CD or MD. :
SWITCHING BETWEEN [XS8] AND [SL16]
The system control mode can be switched over easily with the
following operation.
@ Unplug the AC power cord from the walt outlet. :
@ Set the SYSTEM CONTROL switch on tne rear panel to the desired §
position
: SYSTEM
CONTROL
es ©
© th
Co
(X88)~ |
SLT)
@ This operation d oes not affect the |
tems stored in m
emory
Cernect & cords firmly If connections are !oose, tnere could be less of sound er nose produced
ra 5
a
4) i)
fs
ye. Tet ywwore proceny
Winer oiuaa'ng and unplugging canmeciic™ cords, ne sure to frst remove the pawer cordiram the AC outlet Piugging/ unplugging connection
cards vitrout remova! of the power cora cam cause Ma!furcions or damage 10 the unit.
Do net comnect Uo a power Source wnich 1s larger than that indicated on tne socket at the rear of the unit.
l'tresystem coniral cords or audio cords are nct connecied properly, the remote contro! ar automatic operation between system components