Advertisement
DEG-7200
2. Recall the equalizer curve to be
adjusted.
Recail a factory curve or user's Curve
(equalizer curve created and stored in
this unit by yourself).
(Refer to "Recalling a Factory Curve" on
page 7 and "Recalling a User's Curve" .)
*
Auser's curve in which no equalizer
curve has been set (= flat curve) cannot
be adjusted with nuance control.
3. Press (A).or (¥) side of buttons [5] to
apply nuance control.
Pressing the (A) side increases the
amount of compensation (increases the
difference between high and low levels.)
Pressing the (W) side decreases the
.
amount of compensation (towards flat.)
(Numeric display shows "—6 — 6".)
+
The nuance control can be applied
separately to the factory curves and
user's curves.
*
The condition after nuance control of
each factor curve or user's curve is
stored as the setting value for than
curve. The next time the factory curve
or user's curve is recalled, the equalizer |
curve after nuance contro! will be
recalled.
Storing Equalizer Curves
The equalizer curves adjusted by the user
can be stored as the user's curves in the
memory under 4 buttons [9].
Storing a User's Curve in Memory
1. Adjust an equalizer curve as desired.
(Refer to "Adjusting the Equalizer
Curve" on page 7.)
2. Press and hold one of (U1) to (U4) of
buttons [9] that you want to store the
equalizer curve for more than 2
seconds.
{The frame of the "USER 1— USER 4"
indicators [19] corresponding to the
pressed button [9] blinks during storing
and lights up after completion of.
storing.)
¢
If an equalizer curve has aiready been
'stored under the button, the previous
memory is cleared and the new
equalizer curve is stored in memory.
«
When a equalizer curve is stored, its
nuance control value is set to 0.
15-Band Graphic Equalizer
Adjustment
1. Press button [4] to switch to the graphic
equalizer mode.
Each press of button changes the mode
as shown below.
Fader/balance mode
Vv
Nuance control mode
v
Graphic equalizer mode
(Example: ROCK (F1))
2. Recall the equalizer curve to be
adjusted.
Recall a factory curve or user's curve
(equalizer curve created and stored in
this unit by yourself). .
(Refer to-"Recalling a Factory Curve" on
page 7 and "Recalling a User's Curve" .)
Recalling a User's Curve
The equalizer curves stored under buttons
[9] (user's curves) can be recalled as
required.
Press one of (U1) to (U4) of buttons 19] that
store the user's curves to be recalled.
(The display frame [19] of the selected
user's curve lights.)
3. Press (<4) or (») side of buttons [6] to
select the frequency to be adjusted.
25 Hz to 16 kHz (2/3 octave/step)
4. Press (A) or (¥) side of buttons [5] to
adjust the level.
(Numeric display [15] shows "-6 — 6".)}
5. Adjust other frequency bands by
repeating steps 3 and 4 for each of
them.
6. Store the adjusted equalizer curve in
memory.
The adjusted equalizer curve will be
reset when another equalizer curve is
recalied. tf you want to retain the
adjusted curve, store it in the memory
of this unit.
(Refer to "Storing Equalizer Curves" .)
Flat Curve Function
An equalizer can be reset to a flat curve
with asimple operation.
Press and hold one of {F1) to (F4) of
buttons [10] for more than 2 seconds.
The graphic equalizer mode is initiated and
the corresponding equalizer curve is made
flat.
ere
Advertisement
