Hitachi YUTAKI Series Installation And Operation Manual page 58

ELECTRICAL AND CONTROL SETTINGS
Status regarding
compliance with
IEC 61000-3-2 and
IEC 61000-3-12
Equipment complying with
IEC 61000-3-2
(*): Professional use
Equipment complying with
IEC 61000-3-12
Installation restrictions may be
applied by supply authorities
in relation to harmonics
• Check to ensure that existing installation (main power switches, circuit breakers, wires, connectors and wire terminals) already
complies with the national and local regulations.
• The use of the DHW tank heater is disabled as factory setting. If it is desired to enable the DHW tank heater operation during
normal indoor unit operation, adjust the DSW4 pin 3 of the PCB1 to the ON position and use the adequate protections. Refer to
the section "6.2 Electrical connection"
48 PMML0510 rev.1 - 10/2019
Outdoor unit
YUTAKI S
RAS-2WHVNP
RWM-2.0NRE(-W)
RAS-2.5WHVNP
RWM-2.5NRE(-W)
RAS-3WHVNP
RWM-3.0NRE(-W)
RAS-2WHVRP(*)
RWM-4.0NE(-W) (3N~)
RAS-2.5WHVRP(*)
RWM-5.0NE(-W) (3N~)
RAS-3WHVRP (*)
RWM-6.0NE(-W) (3N~)
RAS-4WHNPE (*)
RWM-8.0NE(-W)
RAS-5WHNPE (*)
RWM-10.0NE(-W)
RAS-6WHNPE (*)
RAS-4WHVNPE RWM-4.0NE(-W) (1~)
RAS-5WHVNPE RWM-5.0NE(-W) (1~)
RAS-6WHVNPE RWM-6.0NE(-W) (1~)
RAS-8WHNPE
RAS-10WHNPE
for the detailed information.
Models
Split system
Indoor unit
YUTAKI S COMBI
-
RWD-2.0NRWE-200S(-W)
RWD-2.0NRW(S)E-260S(-W)
RWD-2.5NRWE-200S(-W)
RWD-2.5NRW(S)E-260S(-W)
RWD-3.0NRWE-200S(-W)
RWD-3.0NRW(S)E-260S(-W)
RWD-4.0NWE-260S(-W)
RWD-4.0NW(S)E-260S(-W)
RWD-5.0NWE-260S(-W)
RWD-5.0NW(S)E-260S(-W)
RWD-6.0NWE-260S(-W)
RWD-6.0NW(S)E-260S(-W)
- -
Monobloc
system
YUTAKI M
(R410A) /
YUTAKI M
YUTAKI S80
(R32)
RASM-2VRE(*)
RASM-3VRE(*)
RWH-4.0NFE
RASM-4NE
RWH-5.0NFE
RASM-5NE
RWH-6.0NFE
RASM-6NE
RWH-4.0VNFE
RWH-5.0VNFE
RWH-6.0VNFE
RWH-4.0VNFWE RASM-4VNE
RWH-5.0VNFWE RASM-5VNE
RWH-6.0VNFWE RASM-6VNE
RWH-4.0NFWE
RWH-5.0NFWE
RWH-6.0NFWE
- -