DeWalt DCMWP500 Manual page 57

nOTE: The main handle
sides of the single touch handle tubes before lifting the
single touch handle
1
in Fig. D.
2. Raise the single touch handle
Listen for an audible click and ensure the single touch
handle 1 is locked into position before proceeding.
3. Extend the main handle
clicks is heard. The single touch handle
operation position.
nOTE: Take care to not pinch, pull or otherwise stress
the cord 28 .
Adjusting the Main Handle Height (Fig. F)
The main handle 4 extends to accommodate taller users.
1. To extend the main handle
press the handle release button
handle away from the handle support
click is heard, indicating that it is locked into the lower
height position.
nOTE: The handle release button
bottom of handle support
2. To extend the main handle
press the handle release button
handle away from the handle support
click is heard, indicating that it is locked into the upper
height position.
3. Ensure the main handle
before proceeding.
nOTE: When the battery pack
inserted and the bail handle
indicator will illuminate if the single touch handle
15
not locked into position.
4. To retract the main handle
press the handle release button
handle towards the handle support
4
click is heard, indicating that it is locked into the lower
height position.
5. Ensure the main handle
before proceeding.
Storage Mode (Fig. G‑L)

DANGER: MAKE CERTAIN THE SAFETY KEY IS
REMOVED TO PREVENT ACTUATION BEFORE
REMOVING OR INSTALLING BATTERY.

DANGER: Turn unit off and remove safety key and
battery pack.
1. To retract the main handle
button and push the main handle
5
support 2 until two audible clicks are heard, indicating that
both sides of the handles are locked into position. The main
handle 4 must be fully seated against the handle support.
nOTE: The main handle
windows . If they are not engaged as shown in Fig. G,
29
press the main handle
4
until two audible clicks are heard and both sides of handle
windows 29 are closed as shown in Fig. H.
4 must pop out slightly from both
from the storage position as shown
1 to the locked position.
4 outward until a set of audible
1 is now in the
to the lower height position,
4
5 and pull the main
2 until an audible
is located on the
5
.
2
4 to the upper height position,
5 and pull the main
until an audible
2
4 locks into position
and safety key
26 6
8 is pulled, the handle folding
4 to the lower height position,
and push the main
5
until an audible
2
locks into position
4
, press the handle release
4
towards the handle
4
4 must fully engage the handle
towards the handle support
nOTE: Ensure the two storage latches
the single touch handle
Fig. J before lowering the single touch handle
storage position.
2. Fold the single touch handle
wheels 32
clicks as the two storage latches
storage slots
3. Ensure the single touch handle
position before proceeding.
4. The mower can be stored standing up, with the collection bag
removed, or flat on its wheels as shown in Fig. L.
nOTE: Take care to not pinch, pull or otherwise stress
the cord 28
Grass Collection Bag (Fig. M)

DANGER: Turn unit off and remove safety key and
battery pack.
1. Lift the rear door cover
and place the grass collection bag
so the bag lugs
plastic surfaces of the handle brackets. Then lower the rear
door cover
nOTE: If installed, remove rear side discharge chute
ensure the rear door cover
grass collection bag
Mulching (Fig. N)

are
DANGER: Turn unit off and remove safety key and
battery pack.
is
1
1. To operate mower in mulching mode, remove the grass
collection bag
2. Lift the rear door cover
fully into the mower.
3. Ensure the pins
slots on the mower as shown in Fig. N.
36
4. Be sure rear door cover
Side Discharge (Fig. O)

DANGER: Turn unit off and remove safety key and
battery pack.
1. To operate mower in side discharge mode, remove the grass
collection bag
nOTE: If installed, remove the mulching plug
2. Lift the rear door cover
chute onto the mower and engage slot on left as shown
25
in Fig. O.
3. Release the rear door cover
discharge chute
the mower.
2
1 tubes pop outward as shown in
1 towards the front
into storage position. Listen for two audible
30 slide into the
31 as shown in Fig. K.
1 is locked into storage
.
, remove mulching plug
21
22
20 slide into the slots
21 .
is fully up before installing
21
22 .
or rear side discharge chute
22
21 and slide the mulching plug
on the mulching plug
35
21 is closed.
.
22
21 and hook rear side discharge
21 and ensure the rear side
25 is secured in place before operating
EnGLIsh
30 at the back of
1 into the
,
24
onto the mower
39 on the inside
and
25
.
25
24
engage the
24
24 .
55