HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive Maintenance And Service Manual page 117

device preparation
removing power, 72
warnings and precautions, 67
device, unloading from
diagnostic tools, 31
disposal, battery, 112, 113
dissipating floor mats, 114
document
conventions, 10
prerequisites, 9
related documentation, 9
documentation
HP website, 9
providing feedback, 11
E
electrostatic damage prevention, 113
electrostatic discharge See
electrostatic discharge See
electrostatic sensitive parts
handling, 64
packaging, 64
storing, 64
transporting, 64
enclosure expansion
ACU, 94
ACU-XE, 94
adding enclosures to existing
attaching SCSI cables, 93
rack considerations, 93, 93
recommended procedures, 93
error messages
access control conflict
access control resources
array controller disabled, 53
array controller overheated, 53
array controller overheating, 53
bad hard drive firmware
bad SCSI bus mode non-LVD device
40
bad scsi target, 40
cache data lost battery
cache hardware batteries, 47
cache hardware failed and
chassis nvram contents
cloning refused system
controller too old not
critical lockup detected, 37
dual cache module size
EMU flash failed, 55
fibre device hardware
fibre subsystem hardware
fibre subsystem link failure, 58
fibre switch hardware
firmware flash failed, 39
firmware flash failed on box
fw version is not supported, 40
pallet, 66
ESD, 64
ESD, 113
MSA, 93, 93
detected, 52
exceeded, 52
box, 48
found,
dead, 45
disabled, 45
corrupted, 41
halted, 39
supported, 38
mismatch, 45
failure, 58
failure, 58
failure, 58
#, 55
hard drive failure box, 48
I2C read failure, 40
I2C write failure, 40
invalid config box 3<n>,
invalid SCSI cabling, 57
no cache module found, 45
online upgrade flashing
online upgrade incomplete, 39
PCI bridge ASIC self-test
PCI subsystem hardware
pilot 2 contrlr not supported, 38
recovery ROM autoflash
redundancy failed cache Dimms
44
redundancy failed cache size
redundancy failed firmware
redundancy failed hardware
redundancy failed I/O request
redundancy failed mismatch
redundancy failed mismatch
redundancy failed no second
redundancy failed out-of-memory, 43
redundancy failed PCI Bus
remove other controller
ROM cloning failed, 54
storage box EMU not
storage box fan degraded, 56
storage box fan failed, 55
storage box overheated, 56
storage box overheating, 56
storage box power supply
system halted for cache
too many volumes detected, 52
uncorrected ECC memory, 58
unknown I/O module
volume expansion failure, 51
volume rebuild failure, 51
volume state disabled, 49
volume state failed, 49
volume state missing
volume state wrong hard drive
ESD (electrostatic discharge)
obtaining additional
precautions, 64, 113
preventing, 64
prevention measures, 113
storing products, 113
transporting products, 113
types of damage from, 113
European Union, regulatory compliance
111
F
fan module
LEDs, 28
fault tolerance, removing hard
maintenance and service guide
bay<n>, 49
failed, 39
failure, 57
failure, 57
failed, 54
mismatch,
mismatch, 42
lockup, 43
failure, 41
error, 43
firmware, 42
hardware, 42
controller, 44
error, 44
now, 44
responding, 57
failed, 56
error, 46
detected, 59
drives, 50
replaced, 50
information, 114
notice,
drives, 75
117