DeWalt DG3000 Instruction Manual page 15

I1. EMISSION CONTROL SYSTEM WARRANTY
Emission Control System Warranty (ECS Warranty) for 1997 and later model engines
(a) Applicability: This warranty shall apply to 1997 and later model year engines. The ECS
Warranty Period shall begin on the date the new engine or equipment is purchased by/
delivered to its ultimate purchaser and shall continue for 24 consecutive months thereaf-
ter.
(b) General Emissions Warranty Coverage: DEWALT warrants to the ultimate purchaser of
the new engine or equipments and each subsequent purchaser for a two-year period.
(1) Designed, built and equipped so as to conform with all applicable regulations adopted
by the EPA and CARB pursuant to their respective authority, and
(2) Free from defects in materials and workmanship, which, at any time during the ECS
Warranty Period, may cause a warranted emissions-related part to fail to be identical in
all material respects to the part as described in the engine manufacturer's application
for certification.
The ECS Warranty only pertains to emissions-related parts on your engine, as fol-
lows:
(1) Any warranted, emissions-related parts that are not scheduled for replacement as required
maintenance in the Owner's Manual must be warranted for the ECS Warranty Period. If
any such part fails during the ECS Warranty Period, it shall be repaired or replaced by
DEWALT according to Subsection (4) below. Any such part repaired or replaced under the
ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.
(2) Any warranted, emissions-related part that is scheduled only for regular inspection as
specified in the Owner's Manual must be warranted for the ECS Warranty Period. A state-
ment in such written instructions to the effect of "repair or replace as necessary" shall
not reduce the ECS Warranty Period. Any such part repaired or replaced under the ECS
Warranty shall be warranted for the remainder of the ECS Warranty Period.
(3) Any warranted, emissions-related part that is scheduled for replacement as required
maintenance in the Owner's Manual shall be warranted for the period of time prior to the
first scheduled replacement point for that part. If the part fails prior to the first scheduled
replacement, the part shall be repaired or replaced by DEWALT according to Subsection
(4) below. Any such emissions-related part repaired or replaced under the ECS Warranty
shall be warranted for the remainder of the ECS Warranty Period prior to the first sched-
uled replacement point for such emissions-related part.
(4) Repair or replacement of any warranted, emissions-related part under this ECS
Warranty shall be performed at no charge to the owner at a DEWALT Authorized
Warranty Service Facility. The warranty services or repairs must be provided at all
manufacturer distribution centers that are franchised to service the subject engines.
(5) When the engine is inspected by a DEWALT Authorized Warranty Service Facility, the
owner shall not be held responsible for diagnostic costs if the repair is deemed warrant-
able.
(6) DEWALT shall be liable for damages to other original engine components or approved
modifications proximately caused by a failure under warranty of any emission-related part
covered by the ECS Warranty.
(7) Throughout the ECS Warranty Period, DEWALT shall maintain a supply of warranted
emission-related parts sufficient to meet the expected demand for such emission-related
parts.
(8) Any replacement part may be used in the performance of any Warranty maintenance or
repairs and will be provided without charge to the ultimate purchaser. Such use shall not
reduce DEWALT's ECS warranty obligations.
(9) Add-on or modified parts that are not exempted by the Air Resources Board may not be
used. Such use will be grounds for disallowing a warranty claim made in accordance with
this article. DEWALT will not be liable under this article to warrant failures of warranted
parts caused by the use of such an add-on or modified part.
EMISSION RELATED PARTS INCLUDE THE FOLLOWING:
1) Fuel Metering System:
a) Gasoline carburetor assembly and its internal components.
b) Fuel filter (if equipped)
c) Carburetor gaskets
d) Fuel pump (if equipped)
2) Air Induction System including:
a) Intake pipe/manifold
b) Air cleaner
3) Ignition System including:
a) Spark plug
b) Ignition module/coil
4) Miscellaneous Items Used in Above Systems
a) Vacuum, temperature, and time sensitive valves and switches.
b) Hoses, belts, connectors, and assemblies.
5) Evaporate Emissions Control
a) Fuel Hose certificated for CARB evaporative emission of 2007.
b) Fuel hose clamp
c) carbon canister (if equipped)
d) Roll over valve (if equipped)
e) Fuel tank
f) Fuel cap
6) Exhaust Emissions Control
a) catalytic converter (if equipped)
15