Motorola DCT2000 Installation Manual page 6

Digital cable receiver
Hide thumbs Also See for DCT2000:
Table of Contents

Advertisement

Canadian Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations. Cet appareil numérique de la classe B respects toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
NOTE
FCC Part 68 Statement
This equipment complies with part 68 of the FCC rules. On the rear panel of this equipment is a label
that contains, among other information, the FCC registration number and ringer equivalence number
(REN) for the equipment. If requested, this information must be provided to the telephone company.
The REN is used to determine the quantity of devices that may be connected to the telephone line.
Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to the line, as determined by the total RENs, contact the
telephone company to determine the maximum REN for the calling area.
This equipment uses the following USOC jack: RJC. An FCC-compliant telephone cord and modular
plug is provided with this equipment. This equipment is designed to be connected to the telephone
network or premises wiring using a compatible modular jack that is Part 68 compliant. This equipment
cannot be used on telephone company-provided coin services. Connection to Party Line Service is
subject to state tariffs.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that the temporary discontinuance of services may be required. If advance notice isn't practical,
the telephone company will notify the customer as soon as possible. Also, you will be advised of your
right to file a compliant with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this happens, the telephone company will provide advance
notice in order to maintain uninterrupted service.
If the trouble is causing harm to the telephone system, the telephone company may request that you
remove the equipment from the network until the problem is resolved.
It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device is
connected. This is to avoid damaging the equipment by local lightning strikes and other electrical surges.
Industry Canada CS-03
The Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The
department does not guarantee that the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above
conditions might not prevent degradation of service in some situations. Repairs to certified equipment
should be coordinated by a representative designated by the supplier. Repairs or alterations made by
the user to this equipment, or equipment malfunctions may give the telecommunication company cause
to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas. Users should not attempt to make such
connections themselves, but should contact the appropriate electric inspection authority, or electrician,
as appropriate.
The Ringer Equivalence Number (REN) of this device is 0.4. The Ringer Equivalence Number (REN)
assigned to each terminal device provides an indication of the maximum number of terminals allowed to
be connected to a telephone interface. The termination on an interface may consist of any combination
of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all
devices does not exceed 5. The telephone connection arrangement is a CA11A.
This product was FCC approved under test conditions that included the use of
the supplied cable between system components. To be in compliance with
FCC regulation, the user must use this cable and install it properly.
Statement

Advertisement

Table of Contents
loading

Table of Contents