Setting The Subwoofer Information; Setting The Speakers Information - JVC LVT0858-001A Instructions Manual

"YES" for the subwoofer and "SML" for the front, center and
rear speakers are initial settings. To get best possible sound,
change the subwoofer and speaker settings to fit your listening
conditions.

Setting the Subwoofer Information

Register whether you have connected a subwoofer or not. If you
have already connected a subwoofer, follow the procedure below.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press SETTING.
The CONTROL buttons now work for basic
SETTING
settings.
2
Press CONTROL ∞ (or 5) repeatedly until
"SUBWFR (Subwoofer)" (with the current
setting)* appears on the display.
CONTROL
R ΙΙ
SR
ATT
* "YES" is the initial setting. If you have already changed the
setting, "NO" will be shown.
3
Press CONTROL 3 (or 2) to select "YES."
• Each time you press the button, the subwoofer setting
alternates between "YES" and "NO."
CONTROL
PR ΙΙ
ANALOG L C R
LPCM DSP
SUBWFR LFE
DOLBY D AUTO SR
LS S RS
DTS INPUT ATT
YES : Select this when you have connected a subwoofer.
The subwoofer speaker indicator (
up on the display (see page 11). You can adjust the
subwoofer output level (see page 22).
NO : Select this when you have not connected or have
disconnected a subwoofer.
Setting the Speakers
Information
To obtain the best possible effect from the Surround modes (see
page 32), register the following information after all connections are
completed.
• Speaker Size—FRNT SP, CNTR SP, REAR SP
• Speaker Distance—FRNT D, CNTR D, REAR D
• Crossover Frequency—CROSS
• Low Frequency Effect Attenuator—LFE
• Dynamic Range Compression—D.COMP
Speaker Size—FRNT SP, CNTR SP, REAR SP
Register the sizes of all the connected speakers.
• When you change your speakers, register the information about
the speakers again.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press SETTING.
SETTING
2
Press CONTROL ∞ (or 5) repeatedly until one
Remote
NOT
of the following speakers (with the current
setting)* appears.
CONTROL
ANALOG
LPCM
SUBWFR LFE
DOLBY D
LS
DTS
FRNT SP (Front Speaker) : To register the front speaker size.
CNTR SP (Center Speaker): To register the center speaker size.
REAR SP (Rear Speaker) : To register the rear speaker size.
* "SML (small)" is the initial setting. If you have already
VOL
changed the setting, another size will be shown.
3
Press CONTROL 3 (or 2) to select the
appropriate speaker size.
• Each time you press the button, the speaker size changes as
follows:
CONTROL
ANALOG
LPCM
DOLBY D
DTS
VOL
SUBWFR ) lights
LRG (Large) : Select this when the speaker size is relatively
SML (Small) : Select this when the speaker size is relatively
NO
Remote
NOT
4
Repeat steps
size for the other speakers.
Notes:
• Use the following criteria as reference when adjusting:
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select "LRG (large)," and if it is smaller than 12 cm,
select "SML (small)."
• If you have selected "NO" for the subwoofer, you can only select
"LRG (large)" for the front speaker size.
• If you have selected "SML (small)" for the front speaker size, you
cannot select "LRG (large)" for the center and rear speaker sizes.
The CONTROL buttons now work for basic
settings.
PR ΙΙ
L C R
DSP
AUTO SR
S RS
INPUT ATT
PR ΙΙ
L C R
DSP
SUBWFR LFE
AUTO SR
LS S RS
INPUT ATT
Ex.: When registering the rear speaker size.
large. (See "Notes" below.)
small. (See "Notes" below.)
: Select this when you have not connected a
speaker. (Not selectable for the front speakers.)
2 3
and to select the appropriate
VOL
VOL
15