Panasonic ES2045 Operating Instructions Manual page 8

alcohol.
Wipe the main body only with a
damp cloth. The use of alcohol
etc. may cause discoloration or
deformation of the main body.
Do not press down hard on the
skin protector.
• After cleaning, put the protection
cap on the epilation head.
Cleaning of the shaver head
(Fig. 9)
After using the appliance, always
clean the blades to keep them in a
hygienic state.
• Remove the frame by lifting it from
one side while pressing on the
frame release button.
• Clean with the brush.
Be careful not to apply too much
force on the blade.
Remove the hair that is caught on
the front of the trimmer section by
lifting the trimmer.
Do not disassemble the outer
blades or frames.
• Wipe the attachment area with a
dry cloth.
• After cleaning, put the bikini comb
on the shaver head.
Replacing the outer foil of
the shaver head
(Fig.10)
Never remove the outer foil for other
reason than to change it.
Removing the outer foil
While pushing the outer foil gently
with the fingers, use the fingernail
to release the plastic panel
the blade from the catches
the inside of the frame.
Fitting the new outer foil
Holding the outer foil so that the
surface with the plastic panel
(i.e. the surface that will contact the
inner blade) faces upward, insert
into the frame so that the catches
on the frame fit into the holes on
the foil.
We recommend that the outer foil
be replaced every year and the
inner blade be replaced every two
years.
Safety precautions
• Use only the included charger.
• Please use the appliance at a
temperature of between 5~40°C
(41-104F o )
• Always ensure the appliance is
operated on an electric power
s o u r c e m a t c h e d t o i t s r a t e d
voltage.
• Never operate the appliance if
the cord or adapter are damaged
or overly hot, or if the plug fits
loosely in the power outlet.
• Keep the device away from sources
of heat or flame.
• Do not allow the appliance to be
used by, on, or near children.
• Do not allow the appliance to be
used or left in the vicinity of sinks,
bathrooms, or other high-humidity
areas, where it could be exposed
to water and moisture.
on
• Do not allow the appliance to be
on
immersed in, splashed with, or
14 14
rinsed under water.
• Do not modify the cord or damage
i t i n a n y w a y s u c h a s b y
bending, twisting or pulling on it
unnecessarily.
• Do not wrap the output cord tightly
around the appliance.
• Regularly clean the cord connector,
which plugs into the appliance,
to keep it free of dust and foreign
objects such as pins, etc.
• Replace the shaving foil and the
inner blade when you notice a
reduced shaving performance.
• A damaged or defective appliance
s h o u l d b e r e t u r n e d t o t h e
customer ser vice center or to
an authorized customer service
agent.
• Do not attempt to use a defective
appliance or repair the appliance
yourself. Disassembly and repair
should only be carried out by a
qualified technician.
• The adapter can be positioned in
a vertical or horizontal position.
For environmental protection
and recycling of materials
This epilator contains Ni-MH batteries.
ATTENTION:
2 nickel metal hydride batteries
that are recyclable power the
product you have purchased.
Please call 1-800-8-BATTERY
for information on how to recycle
the batteries.
How to remove the built-
in rechargeable batteries
before disposal of the
epilator
(Fig. 11)
The batteries in this epilator are
not intended to be replaced by
consumers. However, the batteries
may be replaced at an authorized
ser vice center. The procedure
described below is intended only for
removal of the rechargeable batteries
for the purpose of proper disposal.
• Always unplug the charger from
the epilator before disassembling
it.
• Always slide the switch to 1 or 2
until the batteries are completely
discharged.
• Using a screwdriver, disassemble
the unit in the following order.
1. Detach the epilation head
2. Remove the off/on switch
3. Remove the top section
the epilator (3 screws).
4. Remove the two long screws
.
5. Push in the head release buttons
.
6 Push hard on the connector on
the bottom and take out the
drive system .
7. Remove the head release buttons
(1 screw).
15 15
.
.
of