D-Link DPH-80 User Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. IP Phone
  5. DPH-80
  6. User manual
D-Link DPH-80 User Manual

D-Link DPH-80 User Manual

D-link dph-80 ip phone
Hide thumbs Also See for DPH-80:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Manual
DPH-80 IP Phone
User's Guide

Advertisement

Table of Contents
loading

Related Manuals for D-Link DPH-80

Summary of Contents for D-Link DPH-80

  • Page 1 DPH-80 IP Phone User’s Guide...

  • Page 2: Warranty And Registration

    Warranty service for software products may be obtained by contacting a D-Link office within the applicable warranty period. A list of D-Link offices is provided at the back of this manual, together with a copy of the Registration Card. If a Registration Card for the product in question has not been returned to a D-Link office, then a proof of purchase (such as a copy of the dated purchase invoice) must be provided when requesting warranty service.
  • Page 3 D-Link Offices for Registration and Warranty Service The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office. To obtain an RMA number for warranty service as to a hardware product, or to obtain warranty service as to a software product, contact the D-Link office nearest you.

  • Page 4: Limitation Of Liability

    ACCIDENT, FIRE, LIGHTNING OR OTHER HAZARD. LIMITATION OF LIABILITY IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE OR INTERRUPTION OF A D-LINK PRODUCT, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY.

  • Page 5: Table Of Contents

    INSTALLATION .......................7 BASIC CONFIGURATION ....................7 FINAL CONFIGURATION....................10 DPH-80 MGCP (MEDIA GATE CONTROL PROTOCOL) ... ERROR! BOOKMARK NOT DEFINED. IP PHONE CONFIGURATION........ERROR! BOOKMARK NOT DEFINED. INFRASTRUCTURE REQUIREMENTS ......ERROR! BOOKMARK NOT DEFINED. CONFIGURING THE MGCP PHONE ......ERROR! BOOKMARK NOT DEFINED.

  • Page 6: Introduction

    Introduction Introduction The D-Link DPH-80 is a fully featured Ethernet business phone that allows both business and residential customers to benefit from IP Telephony services. It reduces costs by receiving local and long distance voice services and data services over a single network connection.

  • Page 7: Features

    Last number redial Overview The D-Link DPH-80 is a low cost, simple to use and extremely versatile IP phone with the look and feel of a normal PSTN phone. The D-Link IP Phone can operate under any of the three main Internet telephony protocols: Media Gateway Control Protocol (MGCP);...

  • Page 8: Installation

    Basic Configuration IP Address In order to use a Web browser to configure the DPH-80 IP phone, you must make sure the phone has a valid Ethernet connection to a PC or LAN via its Ethernet port. We recommend using a recent version of any widely used browser such as Netscape or Internet Explorer.
  • Page 9 DPH-80 Phone User Manual Basic Configuration • In the General Tab, click on Internet Protocol (TCP/IP).
  • Page 10 Click on Use the following IP address, and enter a value in the 10.1.1.xx range. (Do not use the IP address 10.1.1.80; that address is already in use by the DPH-80 as a default address.) If necessary, change the Subnet mask and the Default gateway to match the values shown above.

  • Page 11: Final Configuration

    Click OK. Final Configuration The DPH-80 is highly versatile and can be configured to operate in any of the three main Internet telephony protocols – MCGP, SIP, and H.323. Please choose the appropriate protocol and follow the directions indicated in the Web- based configuration utility.

  • Page 13: Dph-80 Sip (Session Initiation Protocol)

    IP Phone Configuration Infrastructure Requirements Though the DPH-80 SIP phone will work in any type of LAN network, a 100mbps, switched network is more suitable for providing good quality voice communications. SIP phones need a proxy or redirect server to provide the directory function required to make calls.
  • Page 14 User Name: This is case-insensitive with a maximum of 20 characters. Password: This is case-sensitive with a maximum of 20 characters. After logging in, the D-Link DPH-80 Phone Configuration page is displayed and this page provides links to other pages.
  • Page 15 Configuring the SIP phone Configuration Main Page Click on General Configuration. A new page containing information about your system and the DPH-80 will appear. General Configuration Firmware Version : It shows the current firmware version of the IP phone. It is updated whenever the SIP phone software is updated.
  • Page 16 DPH-80 Phone User Manual Configuring the SIP phone PPP password: This is the password used for PPP authentication with the PPP server while obtaining an IP address via PPPoE. Idle Timeout: This is the time interval in seconds of session inactivity after which the PPP session should be terminated.
  • Page 17 DPH-80 Phone User Manual Configuring the SIP phone Upload Filename (up to 6 characters): This is the filename to upload the configuration parameters from the phone to the TFTP server. It may be 6 characters long at maximum. It should start with a letter and should consist of digits, letters and underscore.

  • Page 18: Sip Configuration

    DPH-80 Phone User Manual SIP Configuration SIP Configuration User Name: The user name is used to identify the caller for display purposes only. It should be maximum 20 characters and should comprise only letters, digits, hyphen and/or underscore. Authentication Password: This is used in authentication along with Phone Number. It should be maximum 20 characters and should comprise only of letters, digits, hyphen and/or underscore.
  • Page 19 DPH-80 Phone User Manual SIP Configuration Proxy Domain Name: This is the name of the domain where the IP phone and the proxy/redirect are being hosted. If the field is included it will be used, instead of proxy IP address, in all SIP messages including registration and authentication messages.
  • Page 20 DPH-80 Phone User Manual SIP Configuration RTP Statistics This is an informational page and shows the RTP statistical data from the current call and the previous call. This page is refreshed every 5 seconds automatically. Packets Received: Number of packets that have been received for the call.
  • Page 21 DPH-80 Phone User Manual SIP Configuration On clicking Yes the following screen will appear. You will be returned to the main page. Configuration Upload...
  • Page 22 DPH-80 Phone User Manual SIP Configuration When clicked, this link will display a warning page. Click ‘yes’ to upload the configuration parameters from the phone to the TFTP server as the upload filename. The TFTP server and filename are set in the General Configuration. Click ‘no’ on the warning page to return to the main page.
  • Page 23 DPH-80 Phone User Manual SIP Configuration The TFTP server and filename are set in the General Configuration. Click ‘no’ on the warning page to return to the main page. Change Login Name and Password Existing User Name: This is the user name that was used to access the MGCP phone from the web browser.
  • Page 24 DPH-80 Phone User Manual SIP Configuration Save and Restart When clicked, this link will display a warning page. Click ‘yes’ to save all the updated parameters to the flash memory and restart the phone so that the latest changes take effect.

  • Page 25: Using The Sip Phone

    ‘#’, ‘#’ signals end of dialing to SIP phone. D-Link SIP phone works in 10, 100, and 10/100 Mbps Ethernet environment. It has an adjustable handset and speaker volume control and it plays tone for all numerical key press.
  • Page 26 HOLD: When pressed, the SIP phone disconnects both microphone and speaker while connection is kept alive. No voice packets are transmitted from the D-Link SIP phone. Hold LED is on. User may press again to release the call. This feature requires support from the remote phone for proper functioning.

  • Page 27: Sip Troubleshooting

    Restore factory defaults: If you enter the specified key sequence, the SIP phone restores the configurable parameters to default values upon next restart. Production testing: If you enter the specific key sequence, the D-Link SIP phone will execute a production test upon next restart. The production test is described later in this section.

  • Page 28: Sip Production Test

    SIP Production Test This section describes the production test supported by the D-Link SIP phone. The main hardware blocks to be tested are (i) LED, (ii) Key Scan, (iii) Hook Switch, (iv) Codec &...
  • Page 29 DPH-80 Phone User Manual SIP Production Test LED Test This is the first test that is performed. This tests the LEDs. In this test, the three LEDs – Mute(Red), Hold(Red) and Speaker(Green) – glow simultaneously for a few seconds and then turn off.

Table of Contents