Filling The Fuel Tank - Toro 04384 Operator's Manual

Important: Check the level of oil every 8 operating
hours or daily. Change the oil and filter initially
after the first 50 hours of operation, thereafter
change the oil and the filter every 150 hours.
However, change the oil more frequently when
the engine is operated in extremely dusty or dirty
conditions.
5. Install the filler cap and dipstick firmly in place.

Filling the Fuel Tank

Use only clean, fresh diesel fuel or biodiesel fuels with low
(<500 ppm) or ultra low (<15 ppm) sulfur content. The
minimum cetane rating should be 40. Purchase fuel in
quantities that can be used within 180 days to ensure fuel
freshness.
Fuel tank capacity: 22.7 L (6 U.S. gallons)
Use summer grade diesel fuel (No. 2–D) at temperatures
above –7° C (20° F) and winter grade (No. 1–D or No.
1–D/2–D blend) below that temperature. Use of winter
grade fuel at lower temperatures provides lower flash point
and cold flow characteristics which will ease starting and
reduce fuel filter plugging.
Use of summer grade fuel above –7° C (20° F) will contribute
toward longer fuel pump life and increased power compared
to winter grade fuel.
DANGER
Under certain conditions, diesel fuel and fuel
vapors are highly flammable and explosive. A fire
or explosion from fuel can burn you and others and
can cause property damage.
• Use a funnel and fill the fuel tank outdoors, in
an open area, when the engine is off and is cold.
Wipe up any fuel that spills.
• Do not fill the fuel tank completely full. Add
fuel to the fuel tank until the level is 6 to 13 mm
(1/4 to 1/2 inch) below the bottom of the filler
neck. This empty space in the tank allows the
fuel to expand.
• Never smoke when handling fuel, and stay away
from an open flame or where fuel fumes may be
ignited by a spark.
• Store fuel in a clean, sealed, safety-approved
container.
Biodiesel Ready
This machine can also use a biodiesel blended fuel of up
to B20 (20% biodiesel, 80% petrodiesel). The petrodiesel
portion should be low or ultra low sulfur. Observe the
following precautions:
•
The biodiesel portion of the fuel must meet specification
ASTM D6751 or EN14214.
•
The blended fuel composition should meet ASTM D975
or EN590.
•
Painted surfaces may be damaged by biodiesel blends.
•
Use B5 (biodiesel content of 5%) or lesser blends in cold
weather
•
Monitor seals, hoses, gaskets in contact with fuel as they
may be degraded over time.
•
Fuel filter plugging may be expected for a time after
converting to biodiesel blends.
•
Contact your distributor if you wish for more information
on biodiesel
DANGER
In certain conditions, fuel is extremely flammable
and highly explosive. A fire or explosion from fuel
can burn you and others and can damage property.
• Fill the fuel tank outdoors, in an open area, when
the engine is cold. Wipe up any fuel that spills.
• Do not fill the fuel tank completely full. Add fuel
to the fuel tank until the level is 25 mm (1 inch)
below the bottom of the filler neck. This empty
space in the tank allows fuel to expand.
• Never smoke when handling fuel, and stay away
from an open flame or where fuel fumes may be
ignited by a spark.
• Store fuel in an approved container and keep it
out of the reach of children. Never buy more
than a 30-day supply of fuel.
• Always place fuel containers on the ground away
from your vehicle before filling
• Do not fill fuel containers inside a vehicle or on
a truck or trailer bed because interior carpets
or plastic truck bed liners may insulate the
container and slow the loss of any static charge.
• When practical, remove equipment from the
truck or trailer and refuel the equipment with its
wheels on the ground.
• If this is not possible, then refuel such equipment
on a truck or trailer from a portable container,
rather than from a fuel dispenser nozzle.
• If a fuel dispenser nozzle must be used, keep the
nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is
complete.
1. Clean around the fuel tank cap
25
(Figure 23).