Table Of Contents - ABB COMMANDER 1900 Series Programming Manual

CONTENTS
Section
1 INTRODUCTION ......................................................... 1
2 GENERAL PROGRAMMING ...................................... 2
2.1 Preparation for Changes to the Parameters ..... 2
2.2 Security System ................................................ 2
3 BASIC CONFIGURATION LEVEL .............................. 2
3.1 Set Up Input (Process Variable, Remote Set
Point and Position Feedback) ........................... 4
3.2 Set Up Pen Range/Event Source ..................... 8
3.3 Set Up Chart ..................................................... 9
3.4 Set Up Alarms ................................................. 10
3.5 Set Up Relay Output ....................................... 15
3.6 Set Up Digital Output ...................................... 18
3.7 Set Up Analog Output ..................................... 20
3.8 Digital Inputs ................................................... 22
3.9 Access Page ................................................... 23
3.10 Scale Adjust .................................................... 24
4 CONTROL CONFIGURATION LEVEL ..................... 27
4.1 Set Points ....................................................... 29
4.1.1 Cascade Control
(without output tracking) ...................... 30
4.1.2 Cascade Control
(with output tracking) ........................... 31
4.1.3 Set Points Page ................................... 32
4.2 Motorized Valve Control ................................. 34
4.2.1 Motorized Valve with Feedback
(Position-Proportioning) ....................... 34
4.2.2 Motorized Valve Control without
Feedback (Boundless) ........................ 34
4.2.3 Valve Page .......................................... 35
4.2.4 Calculation for Control Pulses,
Steps and Deviation
(Boundless Control only) ..................... 35
4.3 Set Up Control ................................................ 36
4.3.1 Set Up Control Page (control type) ..... 36
4.3.2 Set Up Control Page
(power-fail mode) ................................ 38
4.3.3 Set Up Control Page (control actions
and limits - non heat/cool) .................. 40
4.3.4 Set Up Control Page (control actions
and limits - heat/cool) ......................... 41
4.3.5 Set Up Control Page
(default control actions) ....................... 42
4.4 Set Up Operating Page .................................. 44
4.5 Set Up Digital Page ........................................ 45
4.6 Set Up Digital Inputs ....................................... 46
5 ADVANCED CONFIGURATION LEVEL ...................... 47
5.1 Set Up Function Keys ..................................... 48
5.2 Set Up Logic ................................................... 49
5.3 Set Up Pen Functions ..................................... 51
5.4 Input Assignment ............................................ 52
6 CONNECTIONS & LINKS ............................................. 53
1 INTRODUCTION
Page The COMMANDER 1900 series of documentation is shown in
Fig. 1.1. The
Standard Manuals
sheet, are supplied with all instruments. The
supplied depend on the specification of the
Manuals
instrument.
INSTALLATION
Product Identification
Siting
Mounting
Electrical Connections
Installation Record
IM/C1900-INS
PROGRAMMING
General Programming
Basic Config. Level
Control Config. Level
Advanced Config. Level
Connections & Links
IM/C1900-PGC
ADVANCED SOFTWARE
OPTIONS
Flow Totalisation
Ramp/Soak Profile
Maths Functions
Timer Functions
IM/C1900-ADV
Fig. 1.1 COMMANDER 1900 Documentation
, including the specification
OPERATION
Setting Up
Displays & Controls
Control Operation
Record Operation
Simple Fault Finding
Part No.
IM/C1900-OGC
SPECIFICATION SHT.
Full Specification
Part No.
A - Standard Manuals
Modbus (RTU)
Serial Adaptors
Serial Connections
Programming Pages
ASCII Tables
Part No.
IM/C1900-MOD
B - Supplementary Manuals
Supplementary
Part No.
Part No.
SS C1900
Part No.
1