To Check Programmes; Starting And Canceling Programmes; To Clear A Timer Recording Programme - Panasonic DMR-E60 Operating Instructions Manual

Press [ENTER] (10) when you have finished making
4
changes.
≥To continue programming:
Repeat steps 2, 3 and 4.
Press [PROG/CHECK] (13) or [RETURN] (28).
5
To put the unit on recording standby
, TIMER] (14).
Press [
Ensure " " lights on the unit's display.
To change the timer recording programme
1) While the Timer Programme List Screen is being shown, use
[3, 4] (10) to select the programme you want to change, and
press [ENTER] (10) to show the Timer Programme Correction
screen.
≥You may also select programme by inputting a 2-digit number
using the numeric buttons (4).
≥Use [2, 1] (10) to move to the page preceding or following
the one on display.
2) Move through the items with [1] (10) and change the settings
with [3, 4] (10) and press [ENTER] (10).
Note
≥The built-in clock employs 24-hour system.
≥The remaining time is not shown if you insert discs other than
DVD-RAM or DVD-R.
≥The remaining time displayed is calculated based on the current
recording mode.
≥If the disc is protected (pages 37, 74), the unit switches to
standby but does not go on standby for recording. Check the disc
carefully.
≥Recording is not possible unless you set "Disc Protection" in
"DISC INFORMATION" to "Off". (page 37)
≥You cannot record to a disc if the write protect tab on a cartridge
disc is set to protect. Release this before operation (page 74).
≥Even if the unit is put in the timer recording standby mode or the
timer recording is being performed, you can play a programme.
≥If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording starting
time, the [ ] flashes on the unit display. In this case, press the
, TIMER] (14) button to put the unit in the timer recording
[
standby mode.
≥When recording more than one programme in a row, for
DVD-RAM the first few seconds, and for DVD-R about the first
30 seconds of all programmes from the second one onwards will
not be recorded.

To check programmes

[RAM] [DVD-R]
Press [PROG/CHECK] (13).
The Timer Programme List screen appears.
TIMER
RECORDING
No. Name Date Start Stop
01 BBC 1 15/ 7 TUE 1:19 1:22
W 15/ 7 TUE 1:20
02 BBC 1 2:20
A
F BBC 1
03 23/ 7 WED 8:00 9:00
04 BBC 1 23/ 7 WED 9:00 10:00
X
05 BBC 1 23/ 7 WED 10:00 11:00
New Timer Programme
SELECT
CANCEL
ENTER
RETURN
Icon explanations (A)
¥
This programme is currently recording.
W The programme is overlap with another programme.
F
The disc was full or the maximum number of programmes or
scenes was reached so the programme failed to record.
The television programme was copy-guarded so the
programme failed to record.
X The programme did not complete recording because the
disc is dirty or some other reason.
Remain 1:58 SP
1:19:00 15.7 TUE
Disc
Mode PDC
space
SP OFF OK
SP OFF
OK
B
SP
OFF OK
SP OFF OK
SP OFF
OK
Disc space (B)
OK: Displayed if the recording can fit in the remaining
space on the disc. However, when the programme
becomes longer than scheduled during the
recording by setting "PDC" to "ON", the
programme may not be recorded until its end.
# (Date):
For recordings made daily or weekly, the display
will show until when recordings can be made
based on the time remaining on the disc.
!: Displayed if the disc is not inserted in the unit or is
write-protected (pages 37, 74) or there is not
enough memory capacity left on the disc.
ªTo change the programme
See at left.
ªTo exit from the Timer Programme List screen
Press [PROG/CHECK] (13) or [RETURN] (28). (The television is
shown.)
For your reference
≥Programmes that failed to record are deleted from the list at 4
a.m. the day after tomorrow.

Starting and canceling programmes

[RAM] [DVD-R]
ªTo put the unit on recording standby
, TIMER] (14).
Press [
The unit turns off and "
Note
≥The unit cannot go to timer recording standby if the disc is
protected (pages 37, 74) or full ("
carefully.
ªTo release the unit from recording standby
If you want to record something else before the programme start
time, for example:
, TIMER] (14).
Press [
The unit turns on and "
≥Be sure to press [ , TIMER] (14) before the programme start
time to put the unit on recording standby. The programme only
works if " " is on.
ªTo stop recording while a programme is working
, TIMER] (14).
Press [

To clear a timer recording programme

[RAM] [DVD-R]
Press [CANCEL] (5) or [ERASE] (32) while the
programme's Timer Programme Correction screen is
being shown.
(Alternatively, use [3, 4] (10) to select the programme
in the Timer Programme List screen and press
[CANCEL] (5) or [ERASE] (32).)
≥You can not delete programmes that are currently recording.
34
Timer recording (continued)
" lights on the unit's display.
" flashes). Check the disc
" goes out.