Siemens 7SG11 Manual page 139

Setting name
Gn P/F Highset1 Inhibit
Gn P/F Highset2 Inhibit
Gn E/F Charact. Inhibit
Gn E/F Lowset Inhibit
Gn E/F HighSet 1 Inhibit
Gn E/F HighSet 2 Inhibit
Gn [SEF/REF] Delay1 Inhibit
Gn [SEF/REF] Delay2 Inhibit
Gn [SEF/REF] Lowset Inhibit
Gn Trip Circuit Fail
Gn Waveform Trig
Gn ΣI
2
Update
Gn Reset Flag & Outputs
Gn Clock Sync.
Gn Status 1 P/U Delay
Gn Status 1 D/O Delay
Gn Status 2 P/U Delay
Gn Status 2 D/O Delay
Gn Status 3 P/U Delay
Gn Status 3 D/O Delay
Gn Status 4 P/U Delay
Gn Status 4 D/O Delay
Gn Status 5 P/U Delay
Gn Status 5 D/O Delay
Gn Status 6 P/U Delay
Gn Status 6 D/O Delay
Gn Status 7 P/U Delay
Gn Status 7 D/O Delay
Gn Status 8 P/U Delay
Gn Status 8 D/O Delay
Gn Status 9 P/U Delay
Gn Status 9 D/O Delay
see note below
Gn Alarm 1 *
©2010 Siemens Protection Devices Limited
Ref Applied value
2.3.2
2.3.2
2.3.1
2.3.2
2.3.2
2.3.2
2.4
2.4
2.4
2.10
2.13.3
2.14.1
2.11
2.2.7
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.11 sec
2.2.5
7SG11 Argus 1 Diagrams and Parameters
Setting name
see note below
Gn Alarm 2 *
see note below
Gn Alarm 3 *
see note below
Gn Alarm 4 *
see note below
Gn Alarm 5 *
* The text of these setting names reflects the value
applied to the 'Set Alarm n' settings in the 'System
Config.' menu.
Comms Interface Menu
Setting name
Comms Protocol
IEC Class 2 Measurand
Class 2 Update Period
IEC Class 2 Scaling
Comms Baud Rate
Comms Parity
Relay Address
Line Idle
Data Echo
Data Storage Menu
Setting name
Gn Fault Trigger
Gn Waveform Trig
Gn Waveform Pre-trigger
Clear All Waveforms
Clear All Events
Clear All Faults
Demand Window Type
Demand Window
Maximum Demand Reset
Ref Applied value
2.2.5
2.2.5
2.2.5
2.2.5
Ref Applied value
4.1.1
4.2.6
4.2.7 sec
4.2.8
4.2.9 baud
4.2.10
4.2.11
4.2.12
4.2.13
Ref Applied value
2.13.2
2.13.3
2.13.3 %
2.13.3
2.13.1
2.13.2
2.13.4
2.13.4
2.13.4
P20008 Page 13 of 33